• Journal of the Korean Wood Science and Technology
• /
• 제36권6호
• /
• pp.59-68
• /
• 2008

본 연구에서는 엔드테이핑(End-taping) 처리가 두께가 20~75 mm이고, 직경이 120~470 mm인 백합나무 원반들의 고주파진공건조중 건조결함 예방 미치는 영향에 대하여 조사하였다. Inside end-taping (Inside-ET)과 Outside end-taping (Outside-ET)의 경우 두께 33 mm, 직경 270 mm 이하 원반에서 할렬의 예방효과가 우수하게 나타났다. 직경이 30 cm 이하이고, 두께 60 mm와 두께 75 mm의 원반에서도 전처리을 통하여 경계할렬을 예방할 수 있을 것으로 기대되었다. 경계할렬의 발생위치는 0.50~0.63 diameter 지점으로서 직경에 따라서 상이하였으며, 따라서 횡단면의 부분 엔드테이핑 처리의 경계선도 원반의 직경 따라 적정하게 선정할 필요가 있는 것으로 조사되었다. 중경재의 경우 0.3 diameter 지점이 경계할렬 예방을 위한 전처리의 경계점일 가능성이 높을 것으로 해석된다. 대경재의 경우 경계할렬과 V형 크랙에 의한 손상이 매우 심하였으며, 이는 방사방향으로의 함수율 분포변이가 극심한 백합나무 고유의 재질특성에 기인한 것으로 해석된다. 따라서 대경재의 경우 원반으로 활용하는 것은 적절하지 않는 것으로 생각된다.

• Journal of the Korean Wood Science and Technology
• /
• 제36권2호
• /
• pp.20-28
• /
• 2008

This study was carried out to provide the so-called circumferential slicing method for investigating radial distributions of the tangential strains and of moisture contents within the log cross section (LC) of Kalopanax pictus during indoor drying it. While the heartwood showed an almost uniform moisture content distribution in the range of about 50~55% in case of the green wood, it has gradually decreased toward the outer side, showing about 19% of moisture content difference from the innermost slice. Although the moisture gradient along the radial direction has gradually become gentle as drying progresses, the sapwood of the outer side represented the moisture contents below the fiber saturation point after 24 hours of drying while the heartwood in the inner part showed the moisture contents higher than the fiber saturation point. The pith side was laid under the tensile stress after 24 hours of drying, and then gradually decreasing toward the bark side, and showed the distribution being switched again to the tensile stress on the bark side. As the drying has progressed, this trend got more intensified, and finally showed the U-shaped distribution model after 48 hours of drying. The circumferential slice test is considered to be suitable in quantitatively determining the tangential strains and moisture content within a LC.

• Journal of the Korean Wood Science and Technology
• /
• 제31권1호
• /
• pp.10-15
• /
• 2003

본 연구는 주요 국산 활엽수재 원반에서 채취한 원주상(圓周狀)슬라이스를 오-븐에서 급속건조하면서 각 원반내 함수율의 방사방향 분포추이를 조사하기 위하여 수행하였다. 느티나무의 경우 변재부 또는 심변재경계부가 이미 섬유포화점 이하의 함수율에 도달하였으나, 최내측슬라이스는 아직도 약 40% 정도의 높은 함수율을 나타내었다. 벚나무의 경우 최내측 슬라이스와 바로 인접한 슬라이스간의 수분경사가 건조시간이 경과하면서 더욱 심해지는 경향을 보였다. 음나무 원반에서는 생재상태에서는 심재부의 함수율이 변재부보다 약 23% 정도 더 높은 분포를 보였으며, 이러한 분포유형이 평균함수율 약 15%일 때까지도 지속되었다. 참중나무의 경우 전(全)건조기간에 걸쳐 외주측의 심변재혼합 슬라이스들과 최내측 슬라이스의 함수율이 나머지 부위의 함수율보다 낮은 값을 나타내었다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집A
• /
• pp.211-216
• /
• 2001

The components with the circular cross section have the symmetric combination parts for rotating balance and the crack emanates from the symmetric combination parts. The symmetric cracks from symmetric combination parts make a decrease in the component fatigue life more than single crack. In this study, to estimate the behavior of symmetric cracks, the fatigue test was performed using rotary bending tester on the specimen with a symmetric defects in circular cross section. The material used in this study is Ni-Cr-Mo steel alloy. Under the same stress, the result from the rotary bending fatigue test turned out that the symmetric cracks made a decrease in the fatigue life by 35% more than single crack and the relation between log a and cycle ratio $N/N_f$ obtained linearly.

• Journal of the Korean Wood Science and Technology
• /
• 제30권3호
• /
• pp.104-108
• /
• 2002

Nail withdrawal tests were conducted on clear wood of domestic small diameter logs. Nails were driven into the cross and longitudinal sections of each specimen, then nail withdrawal tests were performed. Nail withdrawal loads are strongly dependent on the direction of nail positions. The average load values for the nail withdrawal both in cross section and longitudinal section are higher in high specific gravity (SG) wood of sawtooth oak (Quercus acutissima Carr.) than those in low SG wood of Korean red pine (Pinus densiflora Sieb. et Zucc.) and pitch pine (Pinus rigida Mill.). The average ratio of the nail withdrawal loads for side-grain and end-grain are higher in the low SG wood than that in the high SG of wood. Both linear and non-linear regression analyses were conducted on nail withdrawal load with SG, good correlations were obtained between nail withdrawal load and SG.

• Journal of the Korean Wood Science and Technology
• /
• 제41권5호
• /
• pp.456-465
• /
• 2013

Log cross sections of yellow poplar were dried in a radio frequency vacuum (RFV) dryer under alternating vacuum and release (AVR) process. The average moisture content (MC), temperature and vapor pressure at the volumetric center were monitored as functions of time. Three different log thicknesses (33, 60 and 75mm) were tested. The results show that the AVR process caused an increase in the drying rate when the moisture content was above fiber saturation point (FSP, about 30% MC) but that it had an inverse effect on the drying rate when the MC was below FSP. The effect of the AVR process on the drying rate decreased, and the severity of heart checks increased, with the increase in the thickness of the specimens.

• 수산해양기술연구
• /
• 제51권3호
• /
• pp.424-431
• /
• 2015

This study was focused on acoustic scattering characteristics of jack mackerel (Trachurus japonicus) at frequency 38, 70, and 120 kHz by Kirchhoff-ray mode (KRM) model. The body length (BL) of 16 individuals ranged in 12.2~22.0 cm ($mean{\pm}S.D.$: $17.8{\pm}3.2cm$) and the swimbladder length ranged in 4.2~8.6 cm ($mean{\pm}S.D.$: $6.6{\pm}1.6cm$) and the swimbladder cross section ranged in $1.7{\sim}6.6cm^2$ ($mean{\pm}S.D.$: $3.8{\pm}1.6cm^2$). This result shows that results correlate well between the BL and the length and cross section of swimbladder. The swimbladder angle ranged in $7{\sim}12^{\circ}$ and the maximum TS values ranged in $-16{\sim}-5^{\circ}$ at tilt angle. The averaged TS-to-BL relationship were $TS_{38kHz}=20{\log}_{10}BL-65.33$ ($R^2=0.66$), $TS_{70kHz}=20{\log}_{10}BL-65.90$ ($R^2=0.67$), and $TS_{120kHz}=20{\log}_{10}BL-66.65$ ($R^2=0.65$). These results can be used fundamental data in order to estimate distribution and biomass of jack mackerel by using hydro-acoustic method.

• Journal of the Korean Wood Science and Technology
• /
• 제47권5호
• /
• pp.644-654
• /
• 2019

참오동나무의 섬유방향기체투과성(gas permeability), 횡단방향 흡음율(sound absorption coefficient)과 음향투과손실(sound transmission loss)을 평가하고 열처리의 영향을 파악하고자 참오동나무 원반을 100, 160, $200^{\circ}C$로 열처리하고 기체투과성, 흡음율, 음향투과손실을 각각 측정하여 무처리 원반의 결과와 비교하였다. 그 결과, 두께 20 mm 참오동나무 원반의 섬유방향 기체투과성(specific permeability)은 무처리, 100, 160, $200^{\circ}C$ 열처리의 경우 각각 0.254, 0.279, 0.314, 0.452로 열처리에 의해 기체투과성이 약간 증가하였다. 두께 20 mm 무처리 참오동나무 원반의 50-6400 Hz 평균흡음율은 0.101이었으며 온도 100, 160, $200^{\circ}C$로 열처리한 목재의 50-6400 Hz 평균흡음율은 0.109, 0.096 그리고 0.106이었다. NRC (noise reduction coefficient) 는 각각 0.060, 0.067, 0.062 그리고 0.071 이었다. 두께 20 mm 무처리 참오동나무 원반의 50-6400 Hz 주파수범위에서 음향투과손실은 평균 36.93 dB이었다. 열처리에 의해 참오동나무 원반의 기체투과성과 흡음율은 열처리에 의해 그리고 열처리 온도 증가에 의해 약간 증가하였으나 증가정도는 미미하였다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2004년도 춘계학술발표회
• /
• pp.815-822
• /
• 2004

A knowledge of in situ stress state is important to design various engineering structures such as dams, tunnels and so on. There are about three wellknown indicators that is, borehole will breakouts, hydraulic fracturing, ellipsoidal cross section of borehole that have been attributed to the state of stress in the vicinity of borehole. Fortunately, Televiewer traveltime image can be used as a caliper log with 144 or 288 arms, which allows to determine the borehole shape. Televiewer amplitude image will give detailed information about the distribution and character of breakouts and hydraulic fracturing as well. For investigation purposes, a series of boreholes(total 195 boreholes: 12.239m) that have been logged all over the country during past 10 years are analyzed. The primary objective of this paper are to examnine the ability of a Televiewer to determine the shape of borehole, to present data inferred by stress indicators, to indicate their possible relationship with the anisotropic horizontal stresses. It is shown that in most cases the fracture orientation statistically estimated from observed fractures denotes an excellent correlation with the orientations inferred by stress indicators. Many intervals of breakouts are terminated at the intersection of oblique fracture with the borehole. The results from Televiewer data are further compared with those of hydraulic fracturing techniques.

• Journal of the Korean Wood Science and Technology
• /
• 제31권2호
• /
• pp.16-23
• /
• 2003

간벌이 국산 잣나무 조림목의 용재품질에 미치는 영향을 구명함으로써 잣나무 인공조림목의 양질재 생산과 효율적 이용을 위한 기초자료를 제공하고자 수행된 본 연구에서 다음과 같은 결과를 얻었다. 강도의 간벌을 실시한 곳에서는 원목의 단위 m당 표면옹이 출현수가 감소하였고, 죽은 옹이의 비율도 감소하였으나 옹이의 크기는 커졌으며, 옹이의 상향각은 죽은옹이가 산옹이보다 컸다. 굽은 원목은 간벌을 하지 않은 곳보다 강도간벌을 실시한 곳에서 적게 출현하였고, 원주형질률은 강도간벌을 실시한 곳에서 높게 나타났으며 지상고 3.2 m 이하 부위의 원목에서 더욱 향상되었다. 무결점재면률은 무간벌구에 비해 강도간벌구에서 향상되었으며, 원목품등은 간벌을 강하게 실시한 경우일수록 높게 나타났다.