• Journal of the Society of Naval Architects of Korea
• /
• v.51 no.2
• /
• pp.154-161
• /
• 2014

Naval ships have hull appendages which are more exposed to the outside because of its small block coefficient compared with commercial ships. These exposed hull appendages like skeg, strut and shaft line affect the maneuverability of a ship. The effect of hull appendages has considered at initial design stage to estimate more accurate maneuverability. In this paper, sensitivity analysis is used to analyze the effect on maneuverability by hull appendages. 3 DOF maneuvering equations based on Mathematical Modelling Group (MMG) model are used and propeller & rudder model are modified to reflect the characteristics of twin propeller & twin rudder. Numerical maneuvering simulations (Turning test, Zig-zag test) for benchmark naval vessel, David Taylor Model Basin (DTMB) 5415 are performed. In every simulation, it is calculated that stability indices and maneuverability characteristics (Tactical Dia., Advance, 1st Overshoot, Time of complete cycle) with respect to the parameters (area times lift coefficient slope, attachment location) of hull appendages. As a result, two regression formulas are established. One is the relation of maneuverability characteristics and stability indices and the other is the relation of stability indices and hull appendages.

• Journal of the Korean Institute of Telematics and Electronics T
• /
• v.35T no.1
• /
• pp.111-119
• /
• 1998

To predict propagation environments of antenna radiation pattern, it is very important for deceision of service area, selection of the best station location and design of cell etc. By analyzing the propagation prediction model that is varied acceding to the kind of antenna, beam angle, terrain and obstacles, we expect that the economic operating of communication networks, calling quality and service of subscriber will be enhanced. It was measured the fields strength to propose the optimal propargation predicted model of the zone of Seji base station in Naju-city. The simulations of field test are 4 types Hata model, the Egri model, the Carey model and the proposed model. Finally the proposed model are more close agreement with experimental test than other models.

• Journal of Families and Better Life
• /
• v.33 no.2
• /
• pp.35-51
• /
• 2015

The purpose of this study was to provide information for research about residents' opinion toward the physical environments of elderly facilities, through the analysis and investigation on the research methodology of foreign academic journal articles from 1990 to 2014. The study results were as follows: Firstly, purposive sampling was a large majority of both facilities and elderly residents. In quantitative studies, many researchers have conducted simple random, cluster, or stratified sampling. Diverse facilities in area, size, location, and etc. should be considered for participation. The qualifications for residents' participation should be considered as well, so that they all could have autonomy for study participation. Secondly, questionnaire and semi-structured guide were likely to be used in independent and resident care facilities. On the other hand in assisted living and long-term care facilities, open questions and visual material were used as well. A compatible scale should be developed so that elderly having variable functional level could participate independently in the study. Thirdly, in data collection process, compliance with research ethics and well trained interviewer's skill were important for residents' active responses and minimization of response errors. Enough research period of time and mixed study in data collection will decrease the response error.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.27 no.5
• /
• pp.38-47
• /
• 2000

Carbon dioxide is a major greenhouse gas causing climate change. This study quantified annual direct and indirect uptake of carbon by urban greenspace, and annual carbon release from vegetation maintenance and fossil fuel consumption. The study area was whole Chuncheon and Kangleung, and also two districts of Kangnam and Junglang in Seoul, cities located in middle Korea. Carbon uptake by urban greenspace played an important role through offsetting carbon release by 6-7% annually in Chuncheon and Kangleung. For Kangnam and Junglang, where the population density was relatively higher, urban greenspace annually offset carbon release by 1-2%. Future possible tree plantings could double annual carbon uptake by existing trees in urban lands (except natural and agricultural lands) of a study city. Based on study results, planning and management guidelines for urban greenspace were suggested to save energy and to reduce atmospheric $CO_2$ concentrations. They included selection of optimum tree species, proper planting location from buildings, design of multilayered planting, amendment of existing regulations for greenspace enlargement, avoidance f intensive vegetation maintenance, and conservation of natural vegetation.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.1
• /
• pp.217-224
• /
• 2003

The frost and mist in the windshield disturb the sight of driver and passengers especially in winter. This possibly leads to safety problems. In order to export automobiles to the countries of North America, the safety regulation requires the frost of selected area should be completely melted in 30 minutes. The defrost pattern and time for melting of frost are fully dependent on the flow and temperature field near the windshield. Furthermore, the flow and temperature field near the windshield are dependent on the air discharged from defrost nozzle. The present work has been done for understanding the flow features of the discharged air and internal flow within the nozzle duct. The three dimensional Navier-Stokes code was used for performing the generic A/C duct flow analysis. The present results were nearly coincided with experimental data. To perform the parametric study of the effectiveness of the number of guide vanes, the discharge angle and the location of nozzle were changed. The ratio of volume flow rate through defrost nozzle and side exit were compared to investigate the influence of parameters on the effectiveness of defrost nozzle. The velocity profiles and flow patterns of the defrost nozzle duct were also analyzed.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.03a
• /
• pp.63-70
• /
• 2002

In tunnel construction, the information on the rock quality and the location of fault or fracture are crucial for economical design of support pattern and for safe construction of the tunnel. The grade of rock is commonly estimated through the observation with the naked eye of recovered cores in drilling or from physical parameters obtained by their laboratory test. Since drilling cost is quite expensive and terrains of planned sites for tunnel construction are rough in many cases, however, only limited information could be provided by core drilling Electrical resistivity and EM surveys may be a clue to get over this difficulty. Thus we have investigated electrical resistivity and EM field data providing regional Information of the rock Quality and delineating fault and fracture over a rough terrain. In this paper, we present some case histories using electrical resistivity and EM survey for the site investigation of tunnel construction. Through electrical resistivity and EM survey, the range and depth of coal seam was clearly estimated, cavities were detected in limestone area, and weak zones such as joint, fault and fracture have been delineated.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• v.1
• /
• pp.377-382
• /
• 2006

Precision approach and landing of aircraft in a remote landing zone autonomously present several challenges. Firstly, the exact location, orientation and elevation of the landing zone are not always known; secondly, the accuracy of the navigation solution is not always sufficient for this type of precision maneuver if there is no DGPS availability within close proximity. This paper explores an alternative approach for estimating the navigation parameters of the aircraft to the landing area using only time-differenced GPS carrier phase measurement and range measurements from a vision system. Distinct ground landmarks are marked before the landing zone. The positions of these landmarks are extracted from the vision system then the ranges relative to these locations are used as measurements for the extended Kalman filter (EKF) in addition to the precise time-differenced GPS carrier phase measurements. The performance of this navigation algorithm is demonstrated using simulation.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.17 no.3
• /
• pp.1-8
• /
• 1990

The digital terrain model (DTM) or digital elevation model (DEM) is commonly used in representing the continuous variation of relief over space. One of the most frequent applications is to display the three dimensional view of the landform concerned. In this paper, the altitude matrices-regular grid cell format of the elevation in Mt. Kyeryong National Park were used in developing the three dimensional view software for the first time in Korea. It required the removal of hidden lines or surfaces. To do this, it was necessary to identify those surfaces and line segments that are visible and those that are invisible. Then, only the visible portions of the landform were displayed. The assumption that line segments are used to approximate contour surfaces by polygons was used in developing the three dimensional orthographic view. In order to remove hidden lines, the visibility test and masking algorithms were used. The software was developed in the engineering workstation, SUN 3/280 at the Institute of Space Science and Astronomy using 'C' in UNIX operating system. The software developed in this paper can be used in various fields. Some of them are as follows : (1) Landscape design and planning for identifying viewshed area(line of sight maps) (2) For planning the route selection and the facility location (3) Flight simulation for pilot training (4) Other landscape planning or civil engineering purposes

• Journal of the Korean Solar Energy Society
• /
• v.33 no.4
• /
• pp.89-93
• /
• 2013

In recent years, many investigations about photovoltaic power systems have been significantly carried out in the fields of renewable power energy. Such research area generally includes developments of highly efficient solar cells, advanced power conversion systems, and smart monitoring systems. A generic objective of fault detection and diagnosis techniques is to timely recognize unexpected faulty of dynamic systems so that economic demage occurred by such faulty is decreased by means of engineering techniques. This paper presents a novel fault detection approach for photovoltaic power arrays which are electrically connected in series and parallels. In the proposed fault detection scheme, we first measure all of photovoltaic modules located in each array by using electronic sense systems and then compare each measurement in turn to detect location of fault module through statistic computation algorithm. We accomplish real-time experiments to demonstrate our proposed fault detection methodology by using a test-bed system including two 20 watt photovoltaic modules.

• Nuclear Engineering and Technology
• /
• v.35 no.2
• /
• pp.91-107
• /
• 2003

Since DBA(Design Basis Accidents) has been studied rather separately from SA(Severe Accidents) in the conventional nuclear reactor safety analysis, the thermal hydraulics during transition between DBA and SA has not been identified so much as each accident itself. Thus, in this study, the thermal hydraulic behavior from DBA to the commencement of SA has been experimentally and analytically investigated for the long-term cooling phase of LB-LOCA(Large-Break Loss-of-Coolant Accident). Experiments were conducted for both cases of the loop seal open and closed in an integral test loop, named as SNUF (Seoul National University Facility), which was scaled down to l/6.4 in length and 1/178 in area of the APR1400 (Advanced Power Reactor 1400MWe). The core mixture level was a main measured value since it took major role in the fuel heat-up rate, the location of fuel melting initiation and the channel blockage by melting material during SA. Experimental results were compared to MAAP4.03 to assess its model of calculating the core mixture level. MAAP4.03 overestimates the core two- phase mixture level because sweep-out and spill-over and the measures to simulate the status of loop seal are not included, which is against the conservatism. Thus, it is recommended that MAAP4.03 should be improved to simulate the thermal hydraulic phenomena, such as sweep-out, spill-over and the status of loop seal.