• Journal of the Korean Institute of Telematics and Electronics
• /
• v.9 no.2
• /
• pp.1-16
• /
• 1972

In this paper, the characteristics of linearly tapered strip-line filters, where the even-mode and odd-mode characteristic impedances vary linearly with the same degree along the lines, are analyzed. The Impedance parameters of linearly tapered coupled strip-line, which is made by connecting two linearly tapered unsymmetric coupled strip-lines In cascade and the I:no input and output terminals are made equal, are obtained. Using the above parameters, the Image parameters of linearly tapered coupled strip-line filters are derived. The result of analysis shows that the line length can be made shorter and also the stop-band width between the fundamental and second pass-band becomes wider, compared with the coupled strip-line filters which use uniform strip-lines. Furthermore, the difference of impedance levels in the fundsmental and second pass-band becomes larger with the degree of taper of the lines. This property is unique, in comparison with the case of uniform or exponentially tapered strip-line filters.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.11a
• /
• pp.342-345
• /
• 2002

As the size of chip components and module decreases, new patteming method for fine line and geometry is needed. So far, in LTCC(Low Temperature Cofired Ceramic) process, screen printing method has been used generally. But screen printing method has some disadvantages as follows. First, the geometry including line, vias, etc. smaller than $100{\mu}m$ can't be evaluated easily. Second, the patterned dimension is different from designed value, which makes distortion in charactersitics of not only chip components but also modules. Thick film lithography has advantages of thick film screen printing process, low cost and thin film process, fine line feasibility. Using this method, the line with $30{\mu}m$ width and the geometry with expected dimension can be evaluated. In this study, the fine line with $35{\mu}m$ line/space is formed and the embedded capacitor with very small tolerance is developed using thick film lithography.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.3
• /
• pp.342-348
• /
• 2015

This paper presents a new motion detector that has a bubble-layer detection zone using a pulsed-mode oscillator and delay line. The proposed motion detector controls the bubble-layer detection zone with pulse width of transmitted signals and creates IF signals only by reflected signals from the target within the detection zone whose position is determined by time delay of the delay line. The fabricated motion detector uses the pulsed-mode voltage controlled oscillator as a signal source which has a center frequency of 8 GHz, pulse width of 2 nsec and pulse period of 30 nsec. It successfully makes the bubble-layer detection zones at 1 m, 3 m and 5 m distant from itself using two delay lines with 7 nsec and 12 nsec delay, and is also demonstrated to detect the target within the detection zones.

• Asian Pacific Journal of Cancer Prevention
• /
• v.16 no.6
• /
• pp.2555-2559
• /
• 2015

Purpose: To investigate effects of the TESTIN (TES) gene on proliferation and migration of highly metastatic nasopharyngeal carcinoma cell line 5-8F and the related mechanisms. Materials and Methods: The target gene of human nasopharyngeal carcinoma cell line 5-8F was amplified by PCR and cloned into the empty plasmid pEGFP-N1 to construct a eukaryotic expression vector pEGFP-N1-TES. This was then transfected into 5-8F cells. MTT assays, flow cytometry and scratch wound tests were used to detect the proliferation and migration of transfected 5-8F cells. Results: A cell model with stable and high expression of TES gene was successfully established. MTT assays showed that the OD value of 5-8F/TES cells was markedly lower than that of 5-8F/GFP cells and 5-8F cells (p<0.05). Flow cytometry showed that the apoptosis rate of 5-8F/TES cells was prominently increased compared with 5-8F/GFP cells and 5-8F cells (p<0.05). In vitro scratch wound assays showed that, the width of the wound area of 5-8F/TES cells narrowed slightly, while the width of the wound area of 5-8F/ GFP cells and 5-8F cells narrowed sharply, suggesting that the TES overexpression could inhibit the migration ability. Conclusions: TES gene expression remarkably inhibits the proliferation of human nasopharyngeal carcinoma cell line 5-8F and reduces its migration in vitro. Thus, it may be a potential tumor suppressor gene for nasopharyngeal carcinoma.

• Journal of The Korean Astronomical Society
• /
• v.40 no.3
• /
• pp.67-82
• /
• 2007

The basic building block of solar filaments/prominences is thin threads of cool plasma. We have studied the spectral properties of velocity threads, clusters of thinner density threads moving together, by analyzing a sequence of $H{\alpha}$ images of a quiescent filament. The images were taken at Big Bear Solar Observatory with the Lyot filter being successively tuned to wavelengths of -0.6, -0.3, 0.0, +0.3, and +0.6 ${\AA}$ from the centerline. The spectra of contrast constructed from the image data at each spatial point were analyzed using cloud models with a single velocity component, or three velocity components. As a result, we have identified a couple of velocity threads that are characterized by a narrow Doppler width($\Delta\lambda_D=0.27{\AA}$), a moderate value of optical thickness at the $H{\alpha}$ absorption peak($\tau_0=0.3$), and a spatial width(FWHM) of about 1". It has also been inferred that there exist 4-6 velocity threads along the line of sight at each spatial resolution element inside the filament. In about half of the threads, matter moves fast with a line-of-sight speed of $15{\pm}3km\;s^{-1}$, but in the other half it is either at rest or slowly moving with a line-of-sight velocity of $0{\pm}3km\;s^{-1}$. It is found that a statistical balance approximately holds between the numbers of blue-shifted threads and red-shifted threads, and any imbalance between the two numbers is responsible for the non-zero line-of-sight velocity determined using a single-component model fit. Our results support the existence not only of high speed counter-streaming flows, but also of a significant amount of cool matter either being at rest or moving slowly inside the filament.

• Fashion & Textile Research Journal
• /
• v.13 no.6
• /
• pp.934-942
• /
• 2011

This study was intended to analyze conventional grading increments and methods for middle-age men's pants, and to suggest new grading guidelines that will enable to improve satisfaction with size and silhouette as a result of combining the concept of grading, which help maintain the ratio and proportion by sizes as one of ready-made apparel's advantages, with body form oriented and aesthetic approaches. In the apparel industry, the current sizing specifications and methods adopted by relevant companies, as well as the characteristics of body forms of men aged 35 to 55 years were comparatively analyzed to find out problems and ultimately to suggest their solutions or improvements. It was considered that as the conventional grading practices used in the industry were customary on the basis of the past experiences, it was required to take the body forms of target consumers into account and also, to reconsider the conventional grading methods. Analyses of sizing and specifications by brands show that 4 to 19 sizes including 82 or 84 as standard size have been produced. Since men's apparel has a large number of sizes with the large range of sizes, grading is critically important. As silhouettes depend on the distribution of grading rule values at each point of increment pattern in the main regions during grading, it is necessary to consider both size grading and form variations. To maintain an appropriate silhouette with keeping the angle of center back line of a pattern, it is desirable to set the ratio of side line part to center part from the crease line to approximately 3:7. It is required to diversify the values of grading rules according to different sizes and pattern regions in consideration for the body forms of key consumers. In addition, if the natural lines of designs and patterns for the width increments of waist circumference and hip circumference, the increments of hip width in pant's front and back panels, the ratio of grading rule values of the right and left sides of crease line, knee circumference, thigh circumference and so on are taken into account, grading will be satisfactory in the all aspects of size, silhouette and ratio.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.04b
• /
• pp.55-56
• /
• 2009

Small RFID tag antenna were fabricated on Si substrate and their physical and electrical properties were evaluated. With decreasing the size of tag antenna on Si substrate, small SMD-type RFID tags could be fabricated, which is very useful for PCB tracking. Firstly, tag antenna pattern and the electromagnetic properties were simulated with HFSS. The frequency was 13.56MHz, the line-width and line-gap were modeled in the range of $50{\sim}200{\mu}m$. S parameters, SRF, and Q value were calculated from geometry. When the line-width and line-gap were 100um and the loop-turn was 10, the SRF was 80MHZ and the Q value was ca. 9. When the microstrip antenna pattern of aluminum was fabricated by using DC sputtering, Vpp of ca. 1.6V was obtained when the reader-tag distance was 40mm.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.40 no.1
• /
• pp.97-113
• /
• 2016

This study develops pant patterns using body shape, measurement and shell mesh data to decide optimal women's pants according to styles with excellent size, fit and shape for different individuals and silhouettes. Standard landmarks, lines, triangles and structures were set on a 3D scanned lower body shell to represent women in their twenties and flattened as a 2D pattern. Patterns were created and analyzed according to culotte, formal, slacks and tight type considering crotch shape, location of the crotch point, and adjusting waist darts. Flattened patterns were rotated to compare existing methods. The crease lines were then set through the hip protrusion point and compared. The main factor of the pant pattern were extracted, total rise, crotch depth, crotch width, angle of center line, shape of the center line curve, the thigh width, the amount of waist dart, and crease line position. With going tight style from the culotte, the fits are closer to the figure with minimized thigh circumference, the dart amount decreases, the crotch depth increases, the crotch extensions were shorter, and the angle of the center back increased. The total rise is U shape for culotte and is closer to V shape as the silhouette tightens. T-test of appearance evaluation of the developed pant pattern were conducted after analyzing measurements and shapes of each styles. The results of the developed patterns were superior to existing patterns in accordance to hip line between body and pants as well as appearance evaluation. We found systematic mechanisms among pattern factors that create various pant silhouettes. Evidence on classification of the silhouettes of traditional types of pants were explained objectively through the process of playing out 3D forms.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.21 no.7
• /
• pp.1173-1183
• /
• 1997

In order to flatter the figures of average middle aged women by determining harmonious proportions for their costume forms, this study evaluates effects of varying design details of jackets(coats) with blouses and slacks using a ranking test and paired comparisons test. The result from clothing design C-2 which has the best design effect were as follows; 1. In order to look taller, the jacket(coats) is divided vertical long line and it has the emphasis point close to the face. 2. In order to make shoulder width look wider, armhole seam line attached 1-2 cm from the shoulder point. 3. In order to make chest width look slimmer, division was made up of a tailored collar with a deep V-neckline. 4. In order to make waist circumference look slimmer, the jacket has more fitted waist line than loosed it and tailored collar with a deep V-neckline. 5. In the case of the division of upper and lower garments, when the division was closer to the golden section, i.e., when the jacket hemline is hipline and slacks length is the heel excluded length of shoe heels, the overall appearance was better. 6. The V-neckline looked better, when it was cut along a long acute angle to the waist line. Because of dividing along above factors 1-6 i.e., clothing design C-2 was overall harmonious. Appropriate division of costume forms made for an aesthetic composition, which flattered the body types of middle aged women and presented harmonious, beautiful costume design effects. It made the women look taller, slim and balanced, and highlighted middle aged women's sense of beauty.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.38 no.5
• /
• pp.675-689
• /
• 2014

This study developed an ideal jeggings pattern with an improved body fit for 20-24 year old females. The results of the study are as follows. First, samples for wearing test were made using jegging patterns from three manufacturers; subsequently, one pattern with a relatively outstanding body fit was selected from the first test. The selected pattern suggested a tight knee, belly, and crotch, high front waist line, and low back waist line. The side lines were also lean to the front; consequently, the front hip width was extended for 0.5cm for more space around the belly and the extended front knee part for 0.2cm to increase moving suitability to fix the leaning side lines. A 1cm front waist line was extended for 0.5cm to fix it lower; in addition, the back waist line 3.0cm was extended for 0.5cm to heighten it. The crotch width was also extended for 0.5cm to add more space. The second wearing test for the fixed forms were evaluated for their outstanding features in appearance as well as moving functions that were proposed as final jeggings forms. The results of the study suggested a jeggings pattern with a better body fit using manufacturer patterns that can be used as basic data for pant patterns with better fitting using various stretch fabrics.