• Applied Chemistry for Engineering
• /
• v.3 no.3
• /
• pp.482-490
• /
• 1992

2,5-dimethoxy-2,5-dihydrofurfuryl alcohol was electrosynthesized from furfuryl alcohol in methanol solution by using three kinds of metal oxide anode. The electrods were prepared by the following process : Thin layer of semiconducting material such as tin(IV)oxide and antimony(III)oxide was made on the titanium base metal in an electric furnace. The titanium metal block with the layer was coated with ${\alpha}-PbO_2$, ${\beta}-PbO_2$, and $MnO_2$ in each electrolytes by anodic deposition, respectively. The lead dioxide electrodes showed better anti-corrosive property than the manganase dioxide electrode. The yield of the product was 92% which is almost the same as the one with conventional platinum electrodes.

• Journal of the Korean institute of surface engineering
• /
• v.18 no.3
• /
• pp.105-115
• /
• 1985

Lead-tin-copper ternary alloy electrodeposition is conducted onto the inner bore surface of plain bearings as an overlay in order to investigate the effect of slot width, current density and fluoboric acid concentration on the uniformity of overlay. The thickness of overlay is analyzed by means of current distribution resulting from the overvoltage of plating bath and the apparent distance between cathode and anode. The result demonstrate that the uniformity of overlay is remarkably dependent of the slot size and current density, but has little bearing on the fluoboric acid concentration over 100g/L. This present study indicates that uniform overlay is obtainable within the tolerable thickness of ${\pm}2{\mu}m$ by using the slot width of 22mm. The surface morphology examination also shows the important role of concentration polarization of the micro-uniformity of overlay. The micro-uniformity has improved at the low concentration polarization which resulted from operating at the low current density and high fluoboric acid concentration. The surface morphology of deposits exhibits the vivid pyramid crystalline in the plating condition of low concentration polarizatio and all deposits have columnar structure parallel to the applied electric field regardless of the electroplating condition used.

• Current Photovoltaic Research
• /
• v.11 no.3
• /
• pp.96-102
• /
• 2023

Sn-Pb narrow-bandgap perovskite solar cells, which is a light-harvesting layer thicker than 1.3 micrometers, is needed to enhance the low photocurrent. The fabrication of such a thick film through solution processing is a key challenge. Here, we studied and characterized the film by using a precursor solution of increased concentration, comparing it with the universally used 1-micrometer Sn-Pb perovskite film. The increase in molar concentration clearly induced thickness enhancement, but we observed that it also created numerous voids at the interface with bottom charge transporting layer. We hypothesized that these voids might hinder the increase in photocurrent associated with thickness enhancement. By introducing methylammonium chloride (MACl), we successfully fabricated Sn-Pb perovskite film with a thickness of 1.3 micrometer and no voids. Void-controlled Sn-Pb perovskite solar cells not only demonstrated superior short-circuit current density compared to those with voids but also operated smoothly under light exposure.

• Korean Journal of Heritage: History & Science
• /
• v.52 no.3
• /
• pp.38-55
• /
• 2019

The purpose of this study is to clarify the historical flow of baekdong alloy's usage according to the alloying materials mentioned in document records. For this purpose, we first overviewed the use of copper as a base material for white copper alloys and other types of copper alloys. Baekdong is an alloy of copper and other metals and is currently defined as an alloy of copper and nickel. However, depending on the research subjects and time of the scholars, baekdong may be defined as a metal with over a certain percentage of tin added to copper, or as an alloy of tin, zinc, and lead with copper. There is disagreement regarding the interpretation of this term. Baekdong, which started to appear in the literature of the Three Kingdoms Period, has been steadily seen through the Goryeo and Chosun Dynasties to the modern period. It has been used in various ways, according to each age and culture, from the symbol of the office to trading goods, daily life goods, and money. In the literature, baekdong's alloying material is not only copper and nickel, which are currently defined as alloys, but it is the same in that copper is used as the base metal of the alloy, although it varies slightly from generation to generation. In addition to copper, tin, zeolite, and emerald, zinc and lead also appeared. It was found that baekdong, which means alloy, and baekdong, which means white metal, were mixed. Nickel, which is the alloy material of baekdong as it is currently defined, is a metal with a relatively high discovery time and is widely used as a material for modern industrial fields. Nickel was introduced into Korea at the end of the Joseon Dynasty, but its use is not known in detail. In this study, we examined the acceptance and use of nickel-based baekdong in articles of modern newspapers and in statistical data. Based on the experience of craftsmen, we estimated the period when nickel-based alloys were used in crafts. Material is a direct factor in the development and deterioration of technology, and the development of technology is the basis for the changing of civilizations and cultures. In this context, this study was to investigate baekdong with the material of alloys as a starting point.

• Journal of Conservation Science
• /
• v.9 no.1
• /
• pp.1-10
• /
• 2000

In 1993, many bronze artifacts were excavated from the Sanoesa Temple(思惱寺), Chongju, Chungbuk. Twelve items were selected and chemically analyzed with AA Spectrometry and ICP-Atomic Emission Spectrometry. They were also observed under the optical microscopy and SEM. According to the results from chemical analysis, production method and use, these artifacts were classified into four groups: casting, wrought and welding products, and bells. Cast products, probably used for ritual, were alloy of 70% Cu, 10% Sn and 20% Pb. They showed ${\alpha}+{\beta}$ phase as a typical microstructure of casting. The ${\delta}$ phase was rarely observed due to the small amount of Sn. These artifacts included more lead than other alloys. They showed segregation like island-shape on the lead part. Wrought products used for daily too1s. were alloy of 80% Cu and 20% Sn. Since they were consist of ${\alpha}$ phase and martensite ${\beta}$ phase, it could be presumed that they were heat-treated. The production method could be identified from twinned grains in ${\alpha}$ phase. Lead was not included in because it had a bad effect to alloy. The bells were alloyed with 85% Cu, 10% Sn, 5% Pb or 90% Cu and 10% Sn. They show the dendrite structure because they were cast and alloyed with many tin. Weldinged were alloyed with 83% Cu, 12% Sn and 5% Pb. lt showed the fine dendrite structure because of fast cooling in air.

• Conservation Science in Museum
• /
• v.15
• /
• pp.4-25
• /
• 2014

Chuncheon National Museum currently own a bronze Buddhist gong that was discovered in 1987 at the Sudasa Temple site of in Suhangri, Pyeongchang. Significantly, showing many casting defects and areas where was repaired, the Gong offered crucial information about the casting technique. To better understand the production technique, scientific analysis was conducted on various aspects of the gong, including its materials, moulds, chaplets, and defects. Composition analysis revealed that the gong was composed primarily of copper ^71.6wt%, tin ^18.2wt%, and lead ^7.2wt%, along with about 1wt% of both arsenic and antimony. The lead content of the chaplets was higher than that of the gong, and the lead content was the highest in the solder, which was used to fill holes after casting. Surface analysis, based on the parting line, indicated that the gong was most likely produced with the sand casting process. Radiography and close examination of the surface disclosed various casting defects ^{e.g., Cold Shut, Surface Folds, Misrun, and Blowholes Adjacent to Chaplets} and their possible causes. The casting defects of a few holes were filled with soft solder.

• Journal of Korean Society of Environmental Engineers
• /
• v.35 no.7
• /
• pp.464-471
• /
• 2013

In this study, the resource efficiency and future metal resource requirement in photovoltaic (PV) production system were evaluated by using material balance data and life cycle assesment (LCA) method. As a result, in the resource efficiency of ferrous and non-ferrous metal, lead and tin had higher resource efficiency than other materials in all PV systems (SC-Si, MC-Si, CI(G)S, CdTe). In the resource efficiency of rare metals, gallium and rhenium in silicon system and rhenium and rhodium in thin-film system ranked as the first and second high resource efficiency. In case of rare earth metal, gadolinium and samarium took higher resource efficiency. The results of the future metal resource requirement in PV systems showed that 2,545,670 ton of aluminium, 92,069 ton of zinc, 22,044 ton of copper, 1,695 ton of tin and 31 ton of nickel will be needed by 2030 in South Korea, except resource recycling supplement.

• Journal of the Korean Vacuum Society
• /
• v.17 no.1
• /
• pp.28-33
• /
• 2008

Lanthanum modified lead zirconate titanate ($Pb_{1.1}La_{0.08}Zr_{0.65}Ti_{0.35}O_3$) thin films were fabricated on indium doped tin oxide (ITO)-coated glass substrate by R.F magnetron sputtering method. The thin films were deposited at $500^{\circ}C$ and post-annealed with various temperature ($550-750^{\circ}C$) by rapid thermal annealing technique. The structure and morphology of the films were characterized with X-ray diffraction (XRD) and atomic force microscopy (AFM) respectively. The hysteresis loops and fatigue properties of thin films were measured by precision material analyzer. As the annealing temperature was increased, the remnant polarization value was increased from $10.6{\mu}C/cm^2$ to $31.4{\mu}C/cm^2$, and coercive field was reduced from 79.9 kV/cm to 60.9 kV/cm. As a result of polarization endurance analysis, the remnant polarization of PLZT thin films annealed at $700^{\circ}C$ was decreased 15% after $10^9$ switching cycles using 1MHz square wave form at ${\pm}5V$.

• Journal of Conservation Science
• /
• v.28 no.2
• /
• pp.175-184
• /
• 2012

A purpose of this research is to find out characteristic of bronze artifacts and gold ornaments excavated from Xiongnu tombs No. 2~4 at Duurlig Nars in Mongolia through scientific analysis of them. The Tombs are comparatively small. There were still lots of relics remaining although the tombs had been already robbed. Also the tombs are evaluated important since the origin of them show coexisting of chinese and northern style. First of all, an analysis result about bronze vessels found in this site, they have high lead(Pb) content and relatively low tin(Sn) content, as compared with the Bronze Han Mirror and End-fittings of Bronze Parasol Rib. Especially in case of bronze tray and bronze lamp from the no. 2 tomb and also bronze cauldron from the no. 4 tomb contain only 1wt% of tin which means binary alloy composition(Cu-Pb). Also, in the case of gold ornaments found in the no. 2 tomb, they have comparatively high purity. And the research suppose that the high possibility of that they were used soldering using alloy of Au-Cu or diffused bonding(using malachite and copper oxide) for joining gold grains of gold granulation ornament. Further scientific research and analysis in Mongolia and other countries will provide more clues to solve mystery of Xiongnu culture.

• Korean Journal of Heritage: History & Science
• /
• v.57 no.1
• /
• pp.146-159
• /
• 2024

In this study, a study on the production technology of the Buddha statue and the production of raw material origin was conducted through scientific analysis on the Bronze seated Bodhisattva Statue of Goseongsa Temple, a treasure. As a result of microstructure analysis through a metal microscope, it was confirmed that the microstructure of the Bronze seated Bodhisattva Statue of Goseongsa Temple was a process-type dendritic structure, and the casting structure of bronze was well represented, so it was manufactured through casting. Subsequently, as a result of analyzing the alloy composition ratio through SEM-EDS, it was identified as a ternary alloy with 81.26 wt% of copper (Cu) and 16.42 wt% of tin (Sn) and 1.72 wt% of lead (Pb). The results of the analysis of lead isotope ratios using a thermal ionization mass spectrometer (TIMS) were substituted into the distribution of lead isotope ratios on the Korean Peninsula, it was shown in corresponding to Jeolla-do and Chungcheong-do regions and North and South Gyeongsang Province. This suggests that the raw materials used in their production were likely sourced from the mines around Goseong Temple in Gangjin. Despite the fact that the statue is a medium and large Buddha with a total height of 51 centimeters, 1.72 wt% of lead (Pb) was found as a result of alloy composition ratio analysis, which showed a similar composition to the lead content ratio of small bronze and gilt-bronze Buddha statues. Therefore, we compared and analyzed the results of the analysis of the composition ratio of the alloys of bronze and gilt bronze statues, which has been scientifically analyzed with a compositional age similar to that of the Bronze seated Bodhisattva Statue of Goseongsa Temple. Comparison results, Various factors, such as the size of the Buddha statue as well as its stylistic characteristics and the age of composition, may exist in determining the alloy composition ratio of the bronze and gilt bronze Buddha statues, and it was confirmed that the alloy composition ratio or casting technology was properly adjusted when the Buddha statue was created. In other words, it is judged that a more comprehensive system of Buddha statue production technology should be investigated by conducting archaeological and art history studies on stylistic characteristics and age of composition, as well as scientific analysis results such as observation of internal structure, microstructure observation, and analysis of alloy composition ratio using radiation transmission irradiation.