• Journal of the Korean Society of Radiology
• /
• v.10 no.8
• /
• pp.565-569
• /
• 2016

Recently, a use of linear accelerator with a multi-leaf collimator(MLC) for radiation therapy is increasing. The importance of quality assurance (QA) for the linear accelerator is emphasized as the side effects of the inaccurate delivery of the radiation beam has been increased according to the high dose irradiation technique. In this study, The $HgI_2$ and $PbI_2$ photoconductor layer samples of $400{\mu}m$ thickness were fabricated using sedimentation method among particle-in-binder technology. From the fabricated samples, the electrical properties(dark current, output current, response properties and linearity) were investigated. From the experimental results, $HgI_2$ has good charge signal generation and linearity. Finally, from the signal response results about various thickness of $HgI_2$ sensor, the signal creation efficiency of $400{\mu}m$ thickness of $HgI_2$ sensor has the highest value and the excellent reproducibility below ${\pm}2.5%$.

• Journal of Gifted/Talented Education
• /
• v.24 no.2
• /
• pp.271-288
• /
• 2014

This study aimed to investigate the perception of earth system thinking of science gifted students in future problem solving (FPS) in relation to climate changes. In order to this study, the research problem associated with climate changes was developed through a literature review. The thirty seven science gifted students participated in lessons. The ideas in problem solving process of science gifted students were analyzed using the semantic network analysis method. The results are as follows. In the problem solving processes, science gifted students are 'changes of the sunlight by water layer', 'changes of the Earth's temperature', 'changes of the air pressure', ' change of the wind and weather' were represented in order. On other hand, regard to earth system thinking for climate changes, while science gifted students were used sub components related to atmospheres frequently, they were used sub components related to biosphere, geosphere, and hydrosphere a little. But, the analytical results of the structural relationship between the sub components related to earth system, they were recognised that biosphere, geosphere, and hydrosphere used very important in network structures. In conclusion, science gifted students were understood well that components of the earth system are influencing each other.

• Korean Journal of Veterinary Research
• /
• v.24 no.2
• /
• pp.149-162
• /
• 1984

The research was conducted(1) to confirm the agent(s) responsible for the antimicrobial activity contained in the fermented tomato juice with L. acidophilus(2) to extract and purify the antimicrobial agent(s)(3) to find the biological, physical and chemical properties of the agent(s). The following results were obtained and summarized as followings; 1. The agent responsible for the inhibitory activity was confirmed by both well assay method using fermented tomato juice with L. acidophilus and turbidimetric technique using the cell-free filtrate or neutralized filtrate of tomato acidohilus culture and found exerted antimicrobial agent other than lactic acid. 2. The procedures of purification : The isolation and purification of antimicrobial agent from the lyophilized acidophilus tomato culture were carried out by (1) methanol extraction (2) acetone extraction, (3) Sephadex G-50 gel filtration (4) paper chromatography and (5) thin layer chromatography. 3. The biological, physical and chemical properties of antimicrobial agent: The biological, physical, chemical properties of the purified antimicrobial agent were: (1) The antimicrobial activity was strong against test organisms; Bacillus subtilis(ATCC 6633), Escheichia coli(ATCC 25922), Staphylococcus aureus(ATCC 167), Pseudomonas fluorescens(KFCC 32394), Proteus vulgaris and Shigella dysenteriae. (2) The pH value of the agent was 2.0 and the inhibitory activity was lost when it was neutralized at 7.0 of pH and the agent was heat stable at $121^{\circ}C$ for 60 minutes. (3) The ultraviolet light absorption spectra of methanol-acetone extract and TLC fraction exhibited a maximum absorption at 260nm and 224nm respectively. (4) The most purified agent from TLC plate increased about 130-fold in activity. (5) The agent isolated from TLC plate was free from $H_2O_2$ or lactic acid. 4. Bioautographic assy: By means of bioautography of the agent on silica gel of TLC plate a strong inhibitory activity against B. subtilis was demonstrated. 5. Mass spectrometry: The agent obtained from TLC plate was analyzed by mass spectrometry which show the parent peak at m/e 264 suggesting the molecular weight of the compound and molecular group such as [$C_2H{^+}_4$], [CO], [CH=NH], [$C_3{H^}4_7$], [$\begin{array}{rcl}O\\{\parallel}\\CH_3-C\\\end{array}$], [$C_6-H{^+}_{11}$], [$C_5H{^+}_{11}$], [$\begin{array}{rcl}O\\{\parallel}\\C_5H_7-C^+\\\end{array}$] were suggested.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2007.05a
• /
• pp.97-105
• /
• 2007

수문학적 토양유형은 복잡하게 세분되어 있는 토양의 종류를 수문학적인 목적에 따라 단순화하기 위해 만든 것으로 미농무성 토양보전국에서 고안한 개념이다. 우리나라 토양을 이 방법으로 구분하고자 하는 몇번의 시도가 있으며 그 중 대표적인 것이 정 등(1995)이 분류한 수문학적 토양군이다. 이는 토양의 침투 투수특성에 대한 실측자료가 부족한 우리나라의 실정을 감안하여 토성속(textural family), 배수등급(drainage class), 불투수층(impermeable layer), 투수성(permeability)의 네가지 토양특성을 분류특성으로 하여 각각에 1-4점 범위로 점수를 매긴 후 합산한 점수를 기준으로 수문학적 토양유형을 분류하는 것이다. 최근에는 토양의 한계침투속도에 따라 수문학적 토양유형을 분류하고자 하는 시도가 있으며 본 논문에서는 새로운 방법으로 분류할 때 기존의 방법과 어떠한 차이가 있는지 비교하고자 하였다. 정 등(1995)의 분류방법은 개념상 몇가지 문제점을 안고 있다. 먼저 토양의 수리특성은 같은 토성속이라 하여도 토양생성 과정과 토지이용 방법에 따라 그 차이가 매우 큼에도 불구하고 이에 대해 고려하지 못하였으며 다음으로 지표유거가 많아 배수가 양호한 토양의 강우 유출을 과소평가한다. 또한 얕은 토심에 존재하는 불투수층이 존재하는 경우 토양의 수리특성에 관계없이 적은 양의 강우에도 유출이 발생하므로 별도의 제한인자로 간주하여야 한다. 토양의 한계 침투속도를 이용한 분류방법은 이러한 문제점을 상당 부분 개선할 수 있다. 토양의 한계침투속도를 산정하기 위해 현장에서 지표 한계침투속도와 투수속도를 측정하였으며 이 자료를 확장하여 해석하기 위해 입자특성을 이용한 Pedo Transfer Function을 개발하였다. 토심 50 cm 포화시 토양 투수성을 한계 침투속도로 가정하였으며 50 cm 이내에 암반층과 지하수위가 존재할 경우 투수성에 관계없이 D유형으로 분류하였다. 새로운 방법으로 분류한 결과 기존의 분류와 몇가지 차이점이 발견되었다. 가장 큰 차이는 대부분의 논토양이 느린 한계침투속도의 영향으로 D유형에 속한 것이다. 산림토양과 밭토양은 기존 방법과 마찬가지로 A, B유형이 많았으며 암반층을 고려하기 전에는 기존 분류에 비해 강우 유출 가능성이 적은 쪽으로 평가되었다. 그러나 암반층이 존재하는 토양을 고려한 결과 A 또는 B 유형에 속하던 상당수의 산림토양이 새로운 분류에서 D유형으로 분류되었다. 지표 유거가 많아 배수등급이 매우양호로 분류되던 토양은 정 등(1995)의 분류와 비교하여 대부분 강우 유출 가능성이 큰 쪽으로 조정되었다. 새로운 수문학적 토양유형을 이용할 경우 낮은 토심에서 암반층이 발견되는 산림토양이 분포한 유역이나 산림, 밭 등에 식질 토양이 많이 분포하는 유역에서는 기존의 방법을 이용하는 것보다 강우 유출량이 높게 평가될 것으로 판단된다. 앞으로 강우 유출량 실측자료와의 비교를 통해 지속적인 보정을 하여야 할 것이며 특히 불투수층의 존재시 일괄적으로 D유형으로 분류된 토양의 경우 깊이에 따라 C 또는 D 유형으로 세분하여 조정할 필요가 있다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.71-71
• /
• 2011

Dye-sensitized solar cells (DSCs) have drawn great academic attention due to their potential as low-cost renewable energy sources. DSCs contain a nanostructured TiO2 photoanode, which is a key-component for high conversion efficiency. Particularly, one-dimensional (1-D) nanostructured photoanodes can enhance the electron transport for the efficient collection to the conducting substrate in competition with the recombination processes. This is because photoelectron colletion is determined by trapping/detrapping events along the site of the electron traps (defects, surface states, grain boundaries, and self-trapping). Therefore, 1-D nanostructured photoanodes are advantageous for the fast electron transport due to their desirable features of greatly reduced intercrystalline contacts with specified directionality. In particular, anodic TiO2 nanotube (NT) electrodes recently have been intensively explored owing to their ideal structure for application in DSCs. Besides the enhanced electron transport properties resulted from the 1-D structure, highly ordered and vertically oriented nanostructure of anodic TiO2 NT can contribute additional merits, such as enhanced electrolyte diffusion, better interfacial contact with viscous electrolytes. First, to confirm the advantages of 1-D nanostructured material for the photoelectron collection, we compared the electron transport and charge recombination characteristics between nanoparticle (NP)- and nanorod (NR)-based photoanodes in DSCs by the stepped light-induced transient measurements of photocurrent and voltage (SLIM-PCV). We confirmed that the electron lifetime of the NR-based photoanode was much longer than that of the NP-based photoanode. In addition, highly ordered and vertically oriented TiO2 NT photoanodes were prepared by electrochemical anodization method. We compared the photovoltaic properties of DSCs utilizing TiO2 NT photoanodes prepared by one-step anodization and two-step anodization. And, to reduce the charge recombination rate, energy barrier layer (ZnO, Al2O3)-coated TiO2 NTs also applied in DSC. Furthermore, we applied the TiO2 NT photoanode in DSCs using a viscous electrolyte, i.e., cobalt bipyridyl redox electrolyte, and confirmed that the pore structure of NT array can enhance the performances of this viscous electrolyte.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.213-213
• /
• 2012

It has been known that quantum confinement effect of CdSe nanocrystal was observed by increasing the number of deposition cycle using successive ionic layer adsorption and reaction (SILAR) method. Here, we report on thermally-induced quantum confinement effect of CdSe at the given cycle number using spin-coating technology. A cation precursor solution containing $0.3\;M\;Cd(NO_3)_2{\cdot}4H_2O$ is spun onto a $TiO_2$ nanoparticulate film, which is followed by spinning an anion precursor solution containing $0.3\;M\;Na_2\;SeSO_3$ to complete one cycle. The cycle is repeated up to 10 cycles, where the spin-coated $TiO_2$ film at each cycle is heated at temperature ranging from $100^{\circ}C$ to $250^{\circ}C$. The CdSe-sensitized $TiO_2$ nanostructured film is contacted with polysulfide redox electrolyte to construct photoelectrochemical solar cell. Photovoltaic performance is significantly dependent on the heat-treatment temperature. Incident photon-to-current conversion efficiency (IPCE) increases with increasing temperature, where the onset of the absorption increases from 600 nm for the $100^{\circ}C$- to 700 nm for the $150^{\circ}C$- and to 800 nm for the $200^{\circ}C$- and the $250^{\circ}C$-heat treatment. This is an indicative of quantum size effect. According to Tauc plot, the band gap energy decreases from 2.09 eV to 1.93 eV and to 1.76 eV as the temperature increases from $100^{\circ}C$ to $150^{\circ}C$ and to $200^{\circ}C$ (also $250^{\circ}C$), respectively. In addition, the size of CdSe increases gradually from 4.4 nm to 12.8 nm as the temperature increases from $100^{\circ}C$ to $250^{\circ}C$. From the differential thermogravimetric analysis, the increased size in CdSe by increasing the temperature at the same deposition condition is found to be attributed to the increase in energy for crystallization with $dH=240cal/^{\circ}C$. Due to the thermally induced quantum confinement effect, the conversion efficiency is substantially improved from 0.48% to 1.8% with increasing the heat-treatment temperature from $100^{\circ}C$ to $200^{\circ}C$.

• Membrane Journal
• /
• v.22 no.6
• /
• pp.404-414
• /
• 2012

In order to investigate $SO_2$ removal, PEI hollow fiber membranes were produced by a dry-wet phase inversion method. The membrane support layer on surface was coated with PEBAX1657$^{(R)}$ and PEG blending materials. Modules were prepared for the single gas permeation characteristics of composite membrane according to temperature and pressure. As a result, $SO_2$ permeance and $SO_2/N_2$ selectivity were 220~1220 GPU and 100~506 through operating condition, respectively. Moreover, $SO_2/CO_2/N_2$ mixture gas was used to compare the performance of separation properties according to temperature, pressure and retentate flow rate difference. $SO_2$ removal efficiency was increased with pressure and temperature.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.16 no.2
• /
• pp.3420-3429
• /
• 1974

This study was performed to estimate the daily water consumption for watering livestock and home use, and to organize the water systems in the rural districts of Korea. For these purposes, 560 farms and other 40 urban families were randomly chosen and investigated about their water systems and daily water consumption seasonally from July 20 to August 31, 1973, and other 82 livestock raisers' useful data for watering livestock helped the study to assess the consumption of livestock water and compare it to that of general farms which bred some domestic animals as their sidelines. The results of data showed that the daily consumption of water was varied with the difference of districts and seasons in which the investigations were conducted. The results were summarized as follows. 1. The mean consumption of water for home use was varied with the range of 30.2-48.7 lit./day in summer and 22.4-45.2 lit./day per a person, respectively, in the rural districts, which showed that the water consumption in summer was more than in autumn. 2. The mean consumption of livestock water in the general farms approached to about 15.8-37.1 lit./day per cattle, 3.87-16.45 lit./day per a pig, and 0.19-1.03 lit./day per chicken, but it was slightly reduced in autumn; 10.89-37.09 lit./day per cattle, 3.87-12.63 lit./day per a pig, and 0.06-0.94 lit./day per chicken. The ratio of livestock water consumption to home use amounted to the range of 10-25%. 3. The mean consumption of livestock water used at the livestock raisers amounted to 134 lit./day per dairy cow, 67.4 lit./day per cattle, 43.29 lit./day per a horse, 13.24 lit./day per a pig, 0.438 lit./day per a layer, and 0.177 lit./day per a broiler, which showed that the daily water consumption for larger livestock was about two times as much as the farms, but it was approximately of the same for small ones. 4. The factors affecting the amount of water consumption for home use were statistically analyzed to find the kind of water sources and the class of water systems by the factorial arrangement method to the fundamental experimental unit, Suwon area of 100 of families, in which the former was very significant while the latter was significant. However, the standard of living and their interactions were not significant. 5. Almost 83.24% of the sampled farms used some kinds of wells as their water sources, of which 32.06% was of hard water, and of which 11.l% or 2.6% contained much of iron or organice materials, respectively, examining them by a simple technique of sensibility, 6. The resulting chart of the farm water systems was summarized as Fig. IV-6. Observating the safe distance from contamination sources, the ratio of 42.4% of sampled farms whose water sources were wells, confronted highly to the danger of contamination to their water sources. And other dangerous sources of contamination such as toilets, stalls, and compost heaps were situated nearly to the water sources, and most of them were able to make their spoiled water infiltrated into the ground. Thereafter, it was recommended to develop some protecting methods and to install some suitable faculties to clean water.

• Analytical Science and Technology
• /
• v.15 no.3
• /
• pp.236-242
• /
• 2002

A method was investigated to determine the thickness of coating on steel sheet using rf glow discharge atomic emission spectrometer. The RF gas-jet boosted glow discharge has such salient feature as good pleasure stability and high sputtering efficiency that it was possible to determine the thickness of silicon resin film on zinc electroplated steel. The erosion speed variation is dependent on discharge power, gas flow rate and discharge pressure. therefore determine discharge condition to measure the thickness of coating on steels. The fundamental studies have been carried out to investigate an optimum condition for in-depth analysis and composition of zinc coating on steel. In this study, the calibration curve for thickness determination of silicon resin film was found to be linear in the range of $1000{\sim}3500mg/m^2$ film thickness. The developed rf gas-jet boosted glow discharge was applied to the analysis of zinc coating and silicon resin film on steel made by RIST.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.2
• /
• pp.84-91
• /
• 2005

For long time, the takeoff and landing control of airship was worked by human handling. With the development of the autonomous control system, the exact controls during the takeoff and landing were required and lots of methods and algorithms were suggested. This paper presents the result of airship take-off and landing by buoyancy control using air ballonet volume change and performance control of pitch angle for stable flight within the desired altitude. For the complexity of airship's dynamics, firstly, simple PID controller was applied. Due to the various atmospheric conditions, this controller didn't give satisfactory results. Therefore, new control method was designed to reduce rapidly the error between designed trajectory and actual trajectory by learning algorithm using an artificial neural network. Generally, ANN has various weaknesses such as large training time, selection of neuron and hidden layer numbers required to deal with complex problem. To overcome these drawbacks, in this paper, the RBFN (radial basis function network) controller developed. The weight value of RBFN is acquired by learning which to reduce the error between desired input output through and airship dynamics to impress the disturbance. As a result of simulation, the controller using the RBFN is superior to PID controller which maximum error is 15M.