• Journal of IKEEE
• /
• v.21 no.2
• /
• pp.123-129
• /
• 2017

Proton Exchange Membrane Fuel Cell (FEMFC) is a strong candidate for future automobile and power generation because of its high power density, low emission and low operation temperature. The major concerns of the gas diffusion layer (GDL) inside a FEMFC is water management. The GDL is typically comprised of carbon for electrical conductivity and PTFE for Hydrophobicity. In this simulation, GDL flooding was investigated using a simplified approach method of an established equation models(Fick' Law, Darcy, Law, Stefan-Maxwell diffusion). The performance of GDL was shown using result of the inner heat, water density and oxygen density of the cell using model equations. The catalyst layer mode in FEMFC showed results of effectiveness factor, Butler-volmer and hydrogen flux density. These results are interesting because the influence of several factors has been shown and the information will be helpful for fuel cell design.

• Journal of the Korean Chemical Society
• /
• v.21 no.5
• /
• pp.353-361
• /
• 1977

In this paper we propose a new theory of multilayer physical adsorption based on the view that a second or higher layer molecule will be adsorbed above the center of a square or triangular array of molecules, rather than on top of molecules themselves, in the next lower layer and the corresponding adsorption isotherm is derived. The derived isotherm contains three adjustable parameters; $v_m$ (monolayer capacity), q/$q_1$ (ratio of the molecular partition function for the second or higher layer vs. that for the first layer) and n (a parameter characterizing the piling pattern of adsorbed molecules). When applied to adsorption of argon on "Carbolac" carbon and nitrogen on Linde silica, excellent agreements between observed and calculated values are obtained up to p/$p_0$ = 0.8. In both cases n = 3 gives the best fit and this probably indicates that adsorbed molecules are piled up in a closest packing pattern.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.1
• /
• pp.51-61
• /
• 1993

A systematic approach of the energy method is proposed for analysis of axisymmetric deep drawing in which the total deforming region is divided into five sections by the geometric characteristic. The corresponding solution is found through optimization of the total energy dissipation with respect to some parameters assumed in the kinematically admissible velocity field defined over each region. The sheet blank is divided into three-or five-layers to consider the bending effect. For the evaluation of frictional energy, it is assumed that the blank holding force acts on the outer rim of the flange and that the contact pressure acting on punch shoulder or die shoulder has uniform distributions, respectively. The computed results by the present method are compared with the experiment and the computed results by the elastic-plastic finite element method for the distribution of thickness strain and the relation between the punch stroke and punch load. The results for the case of multi-layers show better agreements than for the case of a single layer in load vs. stroke relation and strain distribution. It is thus shown that the multi-layer technique can be effectively employed in analyzing axisymmetric deep drawing in connection with the energy method.

• The Journal of Information Systems
• /
• v.29 no.1
• /
• pp.93-111
• /
• 2020

Purpose The purpose of this paper is to observe the relative priorities of importances among the modified versions of Block chain system, being based on AHP decision support model which should be also proposed in this paper. Design/methodology/approach Four versions modified from the beginning of Block chain were divided into Public& Permissionless, Private&Permissionless, Public&Permissioned and Private&Permissioned types. Five criteria for evaluating the four versions whether the version were suitable for Medical information system were introduced from five factors of Technologies Accept Model, which were Security, Availability, Variety, Reliability and Economical efficiency. We designed Decision support model based on AHP which would select the best alternative version suitable for introducing the Block chain technology into the medical information systems. We established the objective of the AHP model into finding the best choice among the four modified versions. First low layer of the model contains the five factors which consisted of Security, Availability, Variety, Reliability and Economical efficiency. Second low layer of the model contains the four modified versions which consisted Public&Permissionless, Private&Permissionless, Public&Permissioned and Private& Permissioned types. The structural questionnaire based on the AHP decision support model was designed and used to survey experts of medical areas. The collected data by the question investigation was analyzed by AHP analysis technique. Findings The importance priority of Security was highest among five factors of Technologies Accept Mode in the first layer. The importance priority of Private&Permissioned type was highest among four modified versions of Block chain technologies in second low layer. The second importance priority was Private&Permissionless type. The strong point of Private&Permissioned type is to be able to protect personal information and have faster processing speeds. The advantage of Private& Permissionless type is to be also able to protect personal information as well as from forging and altering transaction data. We recognized that it should be necessary to develop new Block chain technologies that would enable to have faster processing speeds as well as from forging and altering transaction data.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.24 no.4
• /
• pp.348-353
• /
• 2004

This study is aimed for the implementation of ultrasonic method to assess the reliability of turbine bearings. A modified ultrasonic immersion technique was carried out in both laboratory experiment and field application. From the laboratory results, we confirmed that the condition of interface layer between the babbitt and base metal be monitored by the C-Scan. The C-scan image by the ultrasonic immersion test can be used successfully to observe the condition of interface layer. The testing with a focused transducer provides a promising approach for estimating the extent of the damaged region and observing the interface layer effectively. The difference of the ultrasonic reflection ratio between the bonding and debonding area at the interface layer is one of the key parameters for assessing the extent of the damaged area; additionally, the reflection amplitude exhibits a favorable correlation with the overall damage level. The technique developed in this study was applied to the inspection of the turbine bearings at several power plants in Korea whereby the applicability in the field can be ascertained.

• International Journal of Computer Science & Network Security
• /
• v.21 no.6
• /
• pp.23-28
• /
• 2021

The article discusses the features of adaptation of the parameters of the physical layer of data transmission in self-organizing networks based on unmanned aerial vehicles operating in the conditions of "smart cities". The concept of cities of this type is defined, the historical path of formation, the current state and prospects for further development in the aspect of transition to "smart cities" of the third generation are shown. Cities of this type are aimed at providing more comfortable and safe living conditions for citizens and autonomous automated work of all components of the urban economy. The perspective of the development of urban mobile automated technical means of infocommunications is shown, one of the leading directions of which is the creation and active use of wireless self-organizing networks based on unmanned aerial vehicles. The advantages of using small-sized unmanned aerial vehicles for organizing networks of this type are considered, as well as the range of tasks to be solved in the conditions of modern "smart cities". It is shown that for the transition to self-organizing networks in the conditions of "smart cities" of the third generation, it is necessary to ensure the adaptation of various levels of OSI network models to dynamically changing operating conditions, which is especially important for the physical layer. To maintain an acceptable level of the value of the bit error probability when transmitting command and telemetry data, it is proposed to adaptively change the coding rate depending on the signal-to-noise ratio at the receiver input (or on the number of channel decoder errors), and when transmitting payload data, it is also proposed to adaptively change the coding rate together with the choice of modulation methods that differ in energy and spectral efficiency. As options for the practical implementation of these solutions, it is proposed to use an approach based on the principles of neuro-fuzzy control, for which examples of determining the boundaries of theoretically achievable efficiency are given.

• Current Photovoltaic Research
• /
• v.9 no.4
• /
• pp.145-159
• /
• 2021

Light soaking (LS) stability in polymer solar cells (PSCs) has always been a challenge to achieve due to unstable photoactive layer-electrode interface. Especially, the electron transport layer (ETL) and photoactive layer interface limits the LS stability of PSCs. Herein, we have modified the most commonly used and robust zinc oxide (ZnO) ETL-interface using an organic dye molecule and a co-adsorbent. Power conversion efficiencies have been slightly improved but when these PSCs were subjected to long term LS stability chamber, equipped with heat and humidity (45℃ and 85% relative humidity), an outstanding stability in the case of ZnO/dye+co-adsorbent ETL containing devices have been achieved. The enhanced LS stability occurred due to the suppressed interfacial defects and robust contact between the ZnO and photoactive layer. Current density as well as fill factors have been retained after LS with the modified ETL as compared to un-modified ETL, owing to their higher charge collection efficiencies which originated from higher electron mobilities. Moreover, the existence of less traps (as observed from light intensity-open circuit voltage measurements and dark currents at -2V) are also found to be one of the reasons for enhanced LS stability in the current study. We conclude that the mitigation ETL-surface traps using an organic dye with a co-adsorbent is an effective and robust approach to enhance the LS stability in PSCs.

• Journal of KIISE:Databases
• /
• v.37 no.6
• /
• pp.308-314
• /
• 2010

As the price of flash memory continues to drop and the technology of flash SSD controller innovates, high performance flash SSDs with affordable prices flourish in the storage market. Nevertheless, it is hard to expect that flash SSDs will replace harddisks completely as database storage. Instead, the approach to use flash SSD as a cache for harddisks would be more practical, and, in fact, several hybrid storage architectures for flash memory and harddisk have been suggested in the literature. In this paper, we propose a new approach to use flash SSD as an extended buffer for main buffer in database systems, which stores the pages replaced out from main buffer and returns the pages which are re-referenced in the upper buffer layer, improving the system performance drastically. In contrast to the existing approaches to use flash SSD as a cache in the lower storage layer, our approach, which uses flash SSD as an extended buffer in the upper host, can provide fast random read speed for the warm pages which are being replaced out from the limited main buffer. In fact, for all the pages which are missing from the main buffer in a real TPC-C trace, the hit ratio in the extended buffer could be more than 60%, and this supports our conjecture that our simple extended buffer approach could be very effective as a cache. In terms of performance/price, our extended buffer architecture outperforms two other alternative approaches with the same cost, 1) large main buffer and 2) more harddisks.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.64.2-64.2
• /
• 2010

In order to improve the overall power conversion efficiency in dye-sensitized solar cells (DSSCs), it is very important to secure the sufficient surface area of photocatalytic nanoparticles layer for absorbing dye molecules. It is because increasing the amount of dye absorbed generally results in increasing the amount of light harvesting. In this work, we proposed a new method for increasing the specific surface area of photocatalytic titanium oxide ($TiO_2$) nanoparticles by using an inorganic templating method. Salt-$TiO_2$ composite nanoparticles were synthesized in this approach by spray pyrolyzing both the titanium butoxide and sodium chloride solution. After aqueous removal of salt from salt-$TiO_2$ composite nanoparticles, mesoporous $TiO_2$ nanoparticles with pore size of 2~50 nm were formed and then the specific surface area of resulting porous $TiO_2$ nanoparticle was measured by Brunauer-Emmett-Teller (BET) method. Generally, commercially available P-25 with the average primary size of ~25 nm $TiO_2$ nanoparticles was used as an active layer for dye-sensitized solarcells, and the specific surface area of P-25 was found to be ~50 $m^2/g$. On the other hand, the specific surface area of mesoporous $TiO_2$ nanoparticles prepared in this approach was found to be ~286 $m^2/g$, which is 5 times higher than that of P-25. The increased specific surface area of $TiO_2$ nanoparticles will absorb relatively more dye molecules, which can increase the short curcuit current (Jsc) in DSSCs. The influence of nanoporous structures of $TiO_2$ on the performance of DSSCs will be discussed in terms of the amount of dye molecules absorbed, the fill factor, the short circuit current, and the power conversion efficiency.

• Magazine of the Korea Concrete Institute
• /
• v.5 no.2
• /
• pp.181-188
• /
• 1993

In this study, a numerical method for the material nonlinear analysis of reinforced concrete shell structures including the time dependent effects due to creep and shrinkage is developed. Degenerate shell elements with the layered approach are used. The perfect or strain hardening plasticity model in compression and the linearly elastic model in tension until cracking for concrete are employed. The reinforcing bars are considered as a steel layer of equivalent thickness. Each :steel layer has an uniaxial behaviour resisting only the axial force in the bar direction. A bilinear idealization is adopted to model elasto-plastic stress-strain relationships. For the nonlinear anaysis, incremental load method combined with unbalanced load iterations for each load increment is used. To include time dependent effects of concrete, time domain is divided into several time steps which may have different length. Some numerical examples are presented to study the validity and applicability of the present method. The results are compared with experimental and numerical results obtained by other investigator.