• Journal of Powder Materials
• /
• v.28 no.2
• /
• pp.110-119
• /
• 2021

In this study, the high-temperature oxidation properties of austenitic 316L stainless steel manufactured by laser powder bed fusion (LPBF) is investigated and compared with conventional 316L manufactured by hot rolling (HR). The initial microstructure of LPBF-SS316L exhibits a molten pool ~100 ㎛ in size and grains grown along the building direction. Isotropic grains (~35 ㎛) are detected in the HR-SS316L. In high-temperature oxidation tests performed at 700℃ and 900℃, LPBF-SS316L demonstrates slightly superior high-temperature oxidation resistance compared to HR-SS316L. After the initial oxidation at 700℃, shown as an increase in weight, almost no further oxidation is observed for both materials. At 900℃, the oxidation weight displays a parabolic trend and both materials exhibit similar behavior. However, at 1100℃, LPBF-SS316L oxidizes in a parabolic manner, but HR-SS316L shows a breakaway oxidation behavior. The oxide layers of LPBF-SS316L and HR-SS316L are mainly composed of Cr₂O₃, Fe-based oxides, and spinel phases. In LPBF-SS316L, a uniform Cr depletion region is observed, whereas a Cr depletion region appears at the grain boundary in HR-SS316L. It is evident from the results that the microstructure and the high-temperature oxidation characteristics and behavior are related.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.24 no.6
• /
• pp.597-602
• /
• 2014

We propose hybrid-sensing system for human tracking. This system uses laser scanners and image sensors and is applicable to wide and crowded area such as hallway of university. Concretely, human tracking using laser scanners is at base and image sensors are used for human identification when laser scanners lose persons by occlusion, entering room or going up stairs. We developed the method of human identification for this system. Our method is following: 1. Best-shot images (human images which show human feature clearly) are obtained by the help of human position and direction data obtained by laser scanners. 2. Human identification is conducted by calculating the correlation between the color histograms of best-shot images. It becomes possible to conduct human identification even in crowded scenes by estimating best-shot images. In the experiment in the station, some effectiveness of this method became clear.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.33 no.6
• /
• pp.288-293
• /
• 2023

To optimize the process parameters of laser powder bed fusion process to fabricate the high density STS316L alloy, the effect of laser power, scanning speed and hatching distance on the relative density was studied. Tensile properties of additively manufactured STS316L alloy using optimized parameters was also evaluated according to the build direction. As a result of additive manufacturing process under the energy density of 55.6 J/mm³, 83.3 J/mm³ and 111.1 J/mm³, high density STS316L specimens was suitably fabricated when the energy density, power and scan speed were 83.3 J/mm³, 225 W and 1000 mm/s, respectively. The yield strength, ultimate tensile strength, and elongation of STS316L specimens in direction perpendicular to the build direction, show the most competitive values. Anisotropic shape of the pores and the lack of fusion defects probably caused strain localization which result in deterioration of tensile properties.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.2
• /
• pp.40-49
• /
• 2010

The Purpose of this paper is to weld a rapid palatal expander using a continuous wave Nd:YAG laser. The rapid palatal expander has become a useful treatment method for severe maxillary transverse deficiencies and posterior crossbites. Rapid maxillary expansion is a well-established method to correct transverse maxillary deficiency and arch length discrepancy. The major process parameters studied in the present laser welding experiment were the positions of focus, laser power and travel speed of laser beam. We measured the fusion zone size and its shape using an optical microscope for the observation of cross-sectional area and tension stress of a rapid palatal expander welded. Through the experimental investigation, the optimum speeds and power of laser without deficiencies of weld cross-sectional area were obtained.

• 제어로봇시스템학회:학술대회논문집
• /
• 1997.10a
• /
• pp.1597-1600
• /
• 1997

Most autonomous mobile robots view things only in front of them. As a result they may collide against objects moving from the side or behind. To overcome the problem we have built an Active Omni-directional Range Sensor that can obtain omni-directional depth data by a laser conic plane and a conic mirror. Also we proposed a self-localization algorithm of mobile robot in unknown environment by fusion of Odometer and Active Omn-directional Range Sensor.

• Proceedings of the KWS Conference
• /
• 2006.10a
• /
• pp.123-124
• /
• 2006

This study aimed at exploiting low heat input characteristic of laser welding to effectively control grain coarsening in the fusion zone(FZ) and heat affected zone(HAZ) of 1.5mm thick 18wt% Cr ferritic stainless steel weld. The study demonstrated that as compared with gas tungsten arc welding(GTAW), laser welding brought about significant grain refinement in the FZ and HAZ. However, the impact absorbed energy of GTA weld was superior than that of laser weld because the strengthening effect during welding and cooling stage was higher In laser weld than that in GTA weld. The coarser grains in each weld than base metal resulted in an inferior toughness.

• Journal of Welding and Joining
• /
• v.20 no.6
• /
• pp.796-801
• /
• 2002

Corrosion and tensile properties of zircaloy-4 cladding tube having a laser welding part in elevated temperature are studied to present the criterion of quality evaluation in nuclear reactor and find the scientific basis of SCC, with laser welding method using by coupling up cladding tube to end cap. In the result of tensile test($400^{\circ}C$), the fracture is not happened in the welding part but base metal and the result of corrosion test($400^{\circ}C$ 1500psi steam), corrosion rate of the molten zone and PMZ is a little higher than the other zone.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.36 no.10
• /
• pp.741-747
• /
• 1987

The high-power Nd:glass system with five-stage amplifier was designed and its amplification characteristics was studied for developing high-power Nd:glass laser system as an energy driver of inertial confinement fusion(ICF). In order to study the amplification characteristics of remporal and spacial Gaussian laser beam, the dependence of them on pumping efficiency and rod loss were studied and discussed. The output energy of this system using phosphate Nd glass rod(LHG-7,LHG-8) and silicate Nd glass rod(LSG-91H), respectively, was calculated by the computer simulation using Avizonis-Grotbeck and Frantz Nodvik equations. As results of this simulation, it was found that the shorter the risetime of laser pulse, the larger the amplification factor and that the larger peak value of laser pulse, the lower the amplification factor. The output inergies of 179J, 344J, and 7J were obtained by the designed five-stage amplified high-power Nd:glass laser system using glass rods of LHG-7,LHG-8, and LSG-91H, respectively. From the results it was found that the laser system using the LHG-8 glass rod was the most excellent one among the systems and the cross section for stimulated emission of the gain coefficient was essentially important parameter for the amplification characteristics.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.292-292
• /
• 2000

Since high-power CO$_2$ Laser can be make a high densed energy to Local processing area, manufacturing processes using the laser can be processed for very Localized areas at a very fast rate with minimal or no distortion. Accordingly, the laser has been widely used in the fields of thermal manufacturing processes such as welding, fusion cutting, grooving, and heat treatment of metals. In particular, interest in the laser heat treatment process has grown tremendously in the past few years. In this process, maintaining the uniform hardening depth is important problem to obtain good quality products and to reduce heat induced distortion and residual stress. For achieving this objective, we introduced a new design technique of a fuzzy logic controller that greatly simplified the design procedure by defining several simplified design parameters. In the design procedure, the major design parameters of the controller are characterized by identifying several common aspects. From a series of simulation results, we found that the proposed design technique can be effectively used to design of a fuzzy logic controller for the LASER surface hardening process.

• Journal of the Korean Society for Heat Treatment
• /
• v.32 no.4
• /
• pp.155-160
• /
• 2019

Diamond Like Carbon (DLC) is a metastable form of amorphous carbon that have superior material properties such as high mechanical hardness, chemical inertness, abrasion resistance, and biocompatibility. Furthermore, its material properties can be tuned by additional doping such as nitrogen or boron. However, either pure DLC or doped DLC show poor adhesion property that makes it difficult to apply contact processing technique. Therefore we propose ultrafast laser micromachining which is non-contact precision process without mechanical degradation. In this study, we developed precision machining process of DLC thin film using an ultrafast laser by investigating the process window in terms of laser fluence and laser wavelength. We have also demonstrated various patterns on the film without generating any microcracks and debris.