• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.09a
• /
• pp.157-171
• /
• 2009

A 151 storey super high-rise building located in an area of reclaimed land constructed over soft marine clay in Songdo, Korea is currently under design. This paper describes the design process of the foundation system of the supertall tower, which is required to support the large building vertical and lateral loads and to restrain the horizontal displacement due to wind and seismic forces. The behaviour of the foundation system due to these loads and foundation stiffness influence the design of the building super structure, displacement of the tower, as well as the raft foundation design. Therefore, the design takes in account the interactions between soil, foundation and super structure, so as to achieve a safe and efficient building performance. The site lies entirely within an area of reclamation underlain by up to 20m of soft to firm marine silty clay, which overlies residual soil and a profile of weathered rock. The nature of the foundation rock materials are highly complex and are interpreted as possible roof pendant metamorphic rocks, which within about 50m from the surface have been affected by weathering which has reduced their strength. The presence of closely spaced joints, sheared and crushed zones within the rock has resulted in deeper areas of weathering of over 80m present within the building footprint. The foundation design process described includes the initial stages of geotechnical site characterization using the results of investigation boreholes and geotechnical parameter selection, and a series of detailed two- and three-dimensional numerical analysis for the Tower foundation comprising over 172 bored piles of varying length. The effect of the overall foundation stiffness and rotation under wind and seismic load is also discussed since the foundation rotation has a direct impact on the overall displacement of the tower.

• Journal of the Korean Geotechnical Society
• /
• v.38 no.11
• /
• pp.69-86
• /
• 2022

The railway is widely used to transport passengers and freight due to its punctuality and large transport capacity. The recent remarkable development in construction technology enables various subsea railway tunnels for continent-continent or continent-island connectivity. In Korea, design and construction experience is primarily based on the successful completion of the Boryeong subsea tunnel (2021) and the Gadeok subsea tunnel (2010). However, frequent earthquakes with diverse magnitudes, globally induced and continuously increased the awareness of seismic risks and the frequency of domestic earthquakes. The effect of an earthquake on the subsea tunnel is very complicated. However, ground conditions and seismic waves are considered the main factors. This study simulated four ground types of 3-dimensional numerical models, such as soil, rock, composite, and fractured zone, to analyze the effect of ground type and seismic wave. A virtual subsea railway shield tunnel considering external water pressure was modeled. Further, three different seismic waves with long-term, short-term, and both periods were studied. The dynamic analyses by finite difference method were performed to investigate the displacement and stress characteristics. Consequently, the long-term period wave exhibited a predominant lateral displacement response in soil and the short-term period wave in rock. The artificial wave, which had both periodic characteristics, demonstrated predominant in the fractured zone. The effect of an earthquake is more noticeable in the stress of the tunnel segment than in displacement because of confining effect of ground and structural elements in the shield tunnel. 

• Nuclear Engineering and Technology
• /
• v.52 no.9
• /
• pp.2092-2099
• /
• 2020

Many damages due to flow-accelerated corrosion and cracking have been observed during recent in-service inspections of nuclear power plants. To determine the operability or repair for damaged pipes, an integrity evaluation related to the damaged piping system should be performed by using already proven code and standards. One of them, the ASME Code Case is most popularly used to integrity assessment in nuclear power plants. However, the recent version of CC N-513 still recommends the simplified method which means a damaged elbow is assumed as an equivalent straight pipe. In addition, to enhance the accuracy integrity assessment in elbow, several previous studies recommend that the SIF and elastic COD values for an elbow with relatively large crack could be predicted by an interpolation technique. However, those estimates for elbow with relatively large crack might be derived to inaccurate results for crack growth analysis, such as for the allowable crack size and life estimation. Therefore, in this paper, the effect of crack length (0.3≤θ₁/π≤0.5) on SIF and elastic COD for elbow is systematically investigated. Then, for large crack in elbow, accurate estimates for SIF and elastic COD, which are widely used to assess the integrity of elbows, are proposed. Those proposed solutions are expected to be the technical basis for revisions of CC N-513-4 through the validation.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.41 no.4
• /
• pp.77-85
• /
• 1999

In this study, a computer program considering initial imperfection of axisymmetric reinforced concrete shell which plastic deformation by large external loading was developed . Initial imperfection of dome was assumed as 'dimple type' which can be expressed as Wi=(Wo/h)(1-x$^2$)$^3$. The developed model applied to the analysis of dynamic response of axisymmetric reinforced concrete shell when it has initial imperfection. The initial imperfection of 0.0, -5.0, and 5cm and steel and steel layer ratio 0,3, and 5% were tested for numerical examples . The results can be summarized as follows ; 1. Dynmaic response of vertical deflection at dome crown showed slow increased if it has not inital imperfection . But the response showed relatively high amplitude when initial imperfection was inner directed (opposite direction to loading). Similar trends also appeared for different steel layer ratios. 2. Dynamic responses of radial displacement at the junction of dome and wall showed the highest amplitude when initial imperfection was inward directed (opposite direction to loading). The lowest amplitude occurred when initial imperfection was outward directed (same direction to loading). Vibration period also delayed for inward directed initial imperfection . These trends were obvious as steel layer ratio increasing. 3. The effects of imperfection for the dynamic response of radial displacement a the center of wall scarely appeared. The effects of initial imperfection of dome on the dynmaic response of the wall can be neglected. 4. Effect of steel on the dynmic response of axisymmetric shell structure was great when initial imperfection did not exist. And the effect of direction of initial imperfection (inward or outward) did not show big difference.

• Smart Structures and Systems
• /
• v.12 no.3_4
• /
• pp.251-269
• /
• 2013

Measurement of deflections of certain bridges is usually hampered by corruption of the GPS signal by multipath associated with passing vehicles, resulting to unrealistically large apparent displacements. Field data from the Gorgopotamos train bridge in Greece and systematic experiments revealed that such bias is due to superimposition of two major effects, (i) changes in the geometry of satellites because of partial masking of certain satellites by the passing vehicles (this effect can be faced with solutions excluding satellites that get temporarily blocked by passing vehicles) and (ii) dynamic multipath caused from reflection of satellite signals on the passing trains, a high frequency multipath effect, different from the static multipath. Dynamic multipath seems to have rather irregular amplitude, depending on the geometry of measured satellites, but a typical pattern, mainly consisting of a baseline offset, wide base peaks correlating with the sequence of main reflective surfaces of the vehicles passing next to the antenna. In cases of limited corruption of GPS signal by dynamic multipath, corresponding to scale distortion of the short-period component of the GPS waveforms, we propose an algorithm which permits to reconstruct the waveform of bridge deflections using a weak fusion of GPS and RTS data, based on the complementary characteristics of the two instruments. By application of the proposed algorithm we managed to extract semi-static and dynamic displacements and oscillation frequencies of a historical railway bridge under train loading by using noisy GPS and RTS recordings. The combination of GPS and RTS is possible because these two sensors can be fully collocated and have complementary characteristics, with RTS and GPS focusing on the long- and short-period characteristics of the displacement, respectively.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.3D
• /
• pp.399-405
• /
• 2008

Development of the paved track is required as a low-maintenance of conventional line. The paved tracks are one of the types of the ballast reinforced tracks those are manufactured by adopting the prepacked concrete technique. The main elements of this tracks are large sleeper, low elastic pad, fastener, cement mortar, geotextile and recycled ballast. Low elastic pad is the most effective element of such tracks on the basis of stress-displacement characteristics, dynamic response and fatigue characteristics. The stiffness of the pad determine the stiffness of the track. Consequently, it is more important in case of concrete track structure such as paved track because application of low elastic pad seriously effect the durability and stability of the track. The main objective of this study is to confirm the reduction of train load, which transfer to roadbed through various pad effects. To achieve this task static, numerical analysis and real scale repeated loading test was performed while load reduction effect of low elastic pad was analyzed by using displacement, stress and strain ratio characteristics of the paved track.

• The Korean Journal of Pharmacology
• /
• v.12 no.2 s.20
• /
• pp.1-6
• /
• 1976

The effects of phenoxybenzamine and other related drugs were studied for their interaction with caerulein on gallbladder contraction in anesthetized animals and isolated gallbladder strips. Cholecystostomy and cystic duct ligation were made on anesthetized dog, cat and pig. Pressure changes of gallbladder were measured by a physiological pressure transducer connected to polygraph recorder. Isolated rabbit gallbladder strips were placed in a muscle chamber containing Locke-Ringer solution maintained at $38^{\circ}C$. The contractile responses were measured by a force-displacement transducer connected to polygraph recorder. Caerulein ($30{\sim}200$ ng/kg i.v.) produced marked contraction of gallbladder in situ and the cholecystokinetic potencies appear in decreasing order; dog, cat and pig. The response of caerulein was abolished by the large doses of phenoxybenzamine (15 mg/kg i.v.) but not affected with dibenamine, phentolamine or tolazoline. Cholecystokinetic effect of methacholine or barium chloride was also partially inhibited by phenoxybenzamine and the effect of caerulein was weakly inhibited intravenous injection of cyclophosphamide or papaverine. In isolated rabbit gallbladder strips, the response of contraction to caerulein were progressively inhibited by pretreatment of phenoxybenzamine along with time exposed. These results lead to the conclusion that phenoxytenzamine may inherently inhibit the contractile response of gallbladder to caerulein, and this effect was not related with ${\alpha}-adrenergic$ receptor blocking action.

• Earthquakes and Structures
• /
• v.25 no.6
• /
• pp.443-454
• /
• 2023

Steel shear walls are used to strengthen steel and concrete structures. One such system is Partial Attached Steel Shear Walls (PASSW), which are only connected to frame beams. This system offers both structural and architectural advantages. This study first calibrated the numerical model of RC frames with and without PASSW using an experimental sample. The seismic performance of the RC frame was evaluated by 30 non-linear static analyses, which considered stiffness, ductility, lateral strength, and energy dissipation, to investigate the effect of PASSW width and column axial load. Based on numerical results and a curve fitting technique, a lateral stiffness equation was developed for frames equipped with PASSW. The effect of the shear wall location on the concrete frame was evaluated through eight analyses. Nonlinear dynamic analysis was performed to investigate the effect of the shear wall on maximum frame displacement using three earthquake records. The results revealed that if PASSW is designed with appropriate stiffness, it can increase the energy dissipation and ductility of the frame by 2 and 1.2 times, respectively. The stiffness and strength of the frame are greatly influenced by PASSW, while axial force has the most significant negative impact on energy dissipation. Furthermore, the location of PASSW does not affect the frame's behavior, and it is possible to have large openings in the frame bay.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.8
• /
• pp.719-726
• /
• 2008

In this paper, we designed driving IC for 500 V resonant half-bridge type power converter, In this single-ended level shifter, chip area and power dissipation was decreased by 50% and 23.5% each compared to the conventional dual-ended level shifter. Also, this newly designed circuit solved the biggest problem of conventional flip-flop type level shifter in which the power MOSFET were turned on simultaneously due to the large dv/dt noise. The proposed high side level shifter included switching noise protection circuit and schmmit trigger to minimize the effect of displacement current flowing through LDMOS of level shifter when power MOSFET is operating. The designing process was proved reasonable by conducting Spectre and PSpice simulation on this circuit using 1${\mu}m$ BCD process parameter.

• Journal of the Korean Chemical Society
• /
• v.22 no.5
• /
• pp.281-288
• /
• 1978

Pseudo-first order rate constants $k_{obs}$ were determined for the reactions of naphthalenesulfonyl chlorides (1-NSC and 2-NSC) and anilines. The second order rate constant $k_2$ and third order catalytic $k_3$ were then determined from $k_{obs}$. For 1-NSC peri-hydrogen effect was observed. The large Brønsted ${\beta}$ and large negative slopes ${\rho}$ for the Hammett plots were obtained. These results with the unsually low values of activation parameters were consistent with the $S_AN$-elimination mechanism, but these can be equally well interpreted with the associative $S_N2$mechanism.