• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 춘계학술대회논문집
• /
• pp.1149-1149
• /
• 2006

The leakage characteristic is an important factor in power plant. However, most of power plant have efficiency problem which is occurred leaking between high pressure steam turbine axle and stator. The labyrinth seal which is used between the main turbine axle and stator in the power plant. Because it is able to be non-contact seal and it is minimize clearance to decrease the leakage. But its actual system is too huge to experiment. Therefore, most steam turbine seal performance tests were conducted by air similarity test. This paper described a test facility and program for air similarity test of high pressure steam turbine seal. A test facility has been designed and built to evaluate leakage verification of labyrinth seal. The test facility consist of air compressor, anti-swirl labyrinth seal for 1/3 air similarity model, pressure transducer, air flow measure system, instrumentation and auxiliary system. For evaluation of steam turbine seal performance, the air similarity test of labyrinth seal leakage verification was conducted and we compared experiment data and analysis result.

• 한국방재학회 논문집
• /
• 제9권2호
• /
• pp.87-93
• /
• 2009

래버린스 위어는 마루부의 형상이 직선이 아닌 위어로 월류 폭을 증가시켜 월류량을 증대시키는 수공구조물이다. 최근 강우량 증가에 의한 댐 여수로의 개선 및 관개시설 및 운하관련 수공구조물 등 래버린스 위어의 활용범위는 다양하고 이에 관한 연구가 필요한 실정이다. 본 연구의 목적은 수리모형실험을 통해 삼각형 래버린스 위어 형상에 따른 수리특성 및 유량특성을 분석하여, 삼각형 래버린스 위어의 유량계수식을 제시하는데 있다. 본 연구에서 제시된 유량계수식은 상관계수, 잔차의 합, 평균절대오차율을 분석한 결과 적용성이 있는 것으로 나타나 댐의 여수로 및 관개시설 등 수공구조물 설계에 적용이 가능할 것이다.

• Tribology and Lubricants
• /
• 제37권1호
• /
• pp.31-40
• /
• 2021

This study describes the effects of a thrust labyrinth seal applied to the backside of a centrifugal impeller on the axial thrust force for high speed turbomachinery. The bulk flow model using Neumann's equation calculates the seal cavity pressures and leakage flow rate of the thrust labyrinth seal based on three configurations: teeth-on-rotor (TOR), teeth-on-stator (TOS), and interlocking labyrinth seal (ILS). Prediction results show that the ILS is superior to the TOR and TOS in terms of leakage flow rate. A mathematical model of a centrifugal impeller with a thrust labyrinth seal on its backside calculates the force components corresponding to the impeller inlet, shroud, impeller backside outer, backside seal, and backside inner pressures. A summation of the force components renders the total axial thrust force acting on the centrifugal impeller. The Newton-Raphson numerical scheme iteratively calculates the pressures and leakage flow rate through the impeller wall gap. The prediction results reveal that the leakage flow rate and total axial thrust force increase with rotor speed, and the ILS significantly decreases the leakage flow rate, whereas it slightly increases the axial thrust force when compared to TOR and TOS. Increasing the seal clearance causes an increase in the leakage flow rate and a slight decrease in the axial thrust force with the ILS.

• Tribology and Lubricants
• /
• 제38권2호
• /
• pp.63-69
• /
• 2022

In this research, the rotordynamic characteristics of the labyrinth seal with and without swirl brake were predicted using the computational fluid dynamic (CFD) model. Based on previous studies, a simple swirl brake consisting of square vanes without stagger angle is designed and placed in front of the seal inlet. The rotating frame of reference is utilized to consider the whirling motion of the rotor in the steady-state analysis since the whirling motion is transient behavior in nature. CFD analysis was performed in the range of -1 to 1 pre-swirl ratio for a given seal and swirl brake design and operating conditions. The CFD analysis result shows that the swirl brake effectively reduces the pre-swirl since the circumferential fluid velocity of labyrinth seal with swirl brake was lower than that without swirl brake. The cross-coupled stiffness coefficient, which is greatly affected by the circumferential fluid velocity, increased with an increasing pre-swirl ratio in a seal without a swirl brake but showed a low value in a seal with a swirl brake. The change in the damping coefficient was relatively small. The effective damping coefficient of the labyrinth seal with swirl brake was generally constant and showed a higher value than the labyrinth seal without swirl brake.

• Tribology and Lubricants
• /
• 제39권2호
• /
• pp.61-71
• /
• 2023

This study proposes a procedure for designing a labyrinth seal that meets both leakage flow rate and rotordynamic performance criteria (effective damping, amplification factor, separation margin, logarithmic decrement, and vibration amplitude). The seal is modeled using a one control volume (1CV) bulk flow approach to predict the leakage flow rate and rotordynamic coefficients. The rotating shaft is modeled with the finite element (FE) method and is assumed to be supported by two linearized bearings. Geometry, material and operating conditions of the rotating shaft, and the supporting characteristics of the bearings were fixed. A single labyrinth seal is placed at the center of the rotor, and the linearized dynamic coefficients predicted by the seal numerical model are inserted as linear springs and dampers at the seal position. Seal designs that satisfy both leakage and rotordynamic performance are searched by modifying five seal design parameters using the multi-grid method. The five design parameters include pre-swirl ratio, number of teeth, tooth pitch, tooth height and tooth tip width. In total, 12500 seal models are examined and the optimal seal design is selected. Finally, normalization was performed to select the optimal labyrinth seal designs that satisfy the system performance requirements.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1990년도 제11회 학술강연회초록집
• /
• pp.73-91
• /
• 1990

Incompressible turbulent flow in a single cavity of the stepped multi-cavity labyrinth seal is numerically analyzed to investigate an effect of the shaft speed on the leakage. SIMPLER algorithm is used to solve governing equations, and low-Reynolds k-$\varepsilon$ turbulence model as outlined by Launder and Sharma is adopted to predict turbulent flow. Pressure drops for the cavity with and without the groove are evaluated for four different Reynolds numbersand three different shaft speeds.

• Tribology and Lubricants
• /
• 제6권2호
• /
• pp.27-33
• /
• 1990

Incompressible turbulent flow in a single cavity of the stepped multi-cavity labyrinth seal is numerically analyzed to investigate an effect of the shaft speed on the leakage. SIMPLER algorithm is used to solve governing equations, and low-Reynolds k-$\varepsilon$ turbulence model as outlined by Launder and Sharma is adopted to predict turbulent flow. Pressure drops for the cavity with and without the groove are evaluated for four different Reynolds numbers and three different shaft speeds.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1996년도 제24회 춘계학술대회
• /
• pp.153-157
• /
• 1996

A restrict jetting air is applied against leakage flow to improve a sealing performance of conventional labyrinth seal. A CFD analysis and sealing experiment are introduced to evaluate a sealing performance of applied model. The base of enhanced sealing is explained as a reducing clearance effect by jetting air. As a result, the applied model can improve the sealing performance of labyrinth seal in spite of the wide leakage clearance.

• 한국유체기계학회 논문집
• /
• 제2권3호
• /
• pp.52-58
• /
• 1999

The leakage and rotordynamic coefficients of see-through type gas labyrinth seals are determined using a two-control-volume-model analysis with Moody's wall-friction-factor formula which is defined with a large range of Reynolds number and relative roughness. Jet flow theory are used for the calculation of the recirculation velocity in the cavity. For the reaction force from the labyrinth seal, linearized zeroth-order and the first-order perturbation equations are developed for small motion about a centered position. The leakage and rotordynamic coefficient results of the present analysis are compared with Scharrer's theoretical analysis using Blasius' wall-friction-factor formula and Pelletti's experimental results. The comparison shows that the present analysis using Moody's wall-friction-factor formula and Scharrer's theoretical analysis using Blasius' wall-friction-factor formula give the same results for a smooth seal surface and the range of Reynolds number less than $10^5$.

• 한국정밀공학회지
• /
• 제32권8호
• /
• pp.713-718
• /
• 2015

This article describes the calculation procedure for the dynamic characteristics of a high-pressure labyrinth seal wherein the friction force and rotor whirling force are considered; SFCP, the commercial code developed by Lee and two colleagues, is used in the procedure. The simulation results were reviewed in comparison to those of the experiments provided by Benckert; additionally, the SFCP simulation results were verified using the CFD analysis presented by Toshio Hirano. This calculation procedure may therefore be applied to the dynamic characteristics of the labyrinth seals of high-pressure turbo machinery.