• Tribology and Lubricants
• /
• v.29 no.1
• /
• pp.46-50
• /
• 2013

In this study, the frictional behaviors of articular cartilage against a Co-Cr alloy in two types of kinematic motions were compared. Cartilage pins were punched from the femoral condyles of porcine knee joints, and Co-Cr alloy disks were machined from orthopedic-grade rods and polished to a surface roughness ($R_a$) of 0.002. Friction tests were conducted by using a pin-on-disk-type tribotester in phosphate buffered saline (PBS) under pressures of 0.5, 1, and 2 MPa. All tests were performed in the repeat pass rotational (ROT) and the linear reciprocal (RCP) sliding motions with the same sliding distance and speed of 50 mm/s. The coefficients of friction of the cartilage against the Co-Cr alloy increased with the sliding time in both kinematic motions for all contact pressures. The maximum coefficients of friction in RCP motion were 1.08, 2.82, and 1.96 times those in ROT motion for contact pressures of 0.5, 1, and 2 MPa, respectively. As the contact pressure increased, the coefficients of friction gradually increased in RCP motion, whereas they decrease and then increased in ROT motion. The interaction between the directional change of the shear stress and the orientation of collagen fiber in the superficial layer of the cartilage could affect the change in the frictional behaviors of the cartilage. A large difference in the coefficients of friction between the two kinematic motions could be interpreted as differences in the directional change of shear stress at the contact surface.

• Journal of Mechanical Science and Technology
• /
• v.19 no.10
• /
• pp.1919-1931
• /
• 2005

Human joint motion can be kinematically described in three planes, typically the frontal, sagittal, and transverse, and related to experimentally measured data. The selection of reference systems is a prerequisite for accurate kinematic analysis and resulting development of the equations of motion. Moreover, the development of analysis techniques for the minimization of errors, due to skin movement or body deformation, during experiments involving human locomotion is a critically important step, without which accurate results in this type of experiment are an impossibility. The traditional kinematic analysis method is the Angular-based method (ABM), which utilizes the Euler angle or the Bryant angle. However, this analysis method tends to increase cumulative errors due to skin movement. Therefore, the objective of this study was to propose a new kinematic analysis method, Position-based method (PBM), which directly applies position displacement data to represent locomotion. The PBM presented here was designed to minimize cumulative errors via considerations of angle changes and translational motion between markers occurring due to skin movements. In order to verify the efficacy and accuracy of the developed PBM, the mean value of joint dislocation at the knee during one gait cycle and the pattern of three dimensional translation motion of the tibiofemoral joint at the knee, in both flexion and extension, were accessed via ABM and via new method, PBM, with a Local Reference system (LRS) and Segmental Reference system (SRS), and then the data were compared between the two techniques. Our results indicate that the proposed PBM resulted in improved accuracy in terms of motion analysis, as compared to ABM, with the LRS and SRS.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.11
• /
• pp.3398-3407
• /
• 1996

In this paper, we derive an algorithm and develope a computer program which analyze rapidly and precisely the inverse kinematics of robotic mechanism with spatial complex chain structure based on the relative coordinates. We represent the inverse kinematic problem as an optimization problem with the kinematic constraint equations. The inverse kinematic analysis algorithm, therefore, consists of two algorithms, the main, an optimization algorithm finding the motion of independent joints from that of an end-effector and the sub, a forward kinematic analysis algorithm computing the motion of dependent joints. We accomplish simulations for the investigation upon the accuracy and efficiency of the algorithm.

• Journal of Institute of Control, Robotics and Systems
• /
• v.18 no.9
• /
• pp.823-829
• /
• 2012

An excitation table is commonly used for vibration and ride tests for parts or assemblies of automobiles, aircrafts, or other heavy systems. The authors have analyzed several kinematic properties of an excitation table that is under development for heavy transport vehicles. It consists of one table and 7 linear hydraulic actuators. The authors have performed mobility analysis, inverse kinematics, forward kinematics, and singularity analysis. Especially, we have proposed a fast forward kinematic solution considering the limited motion of the excitation table. On the assumption that the motion variables such as rotation angles and displacements are small, the forward kinematic problem is converted to the observer problem of a linear system. This provides a fast solution. Also we have verified that there are no singularity points in the working range by numerical analysis.

• Korean Journal of Applied Biomechanics
• /
• v.14 no.2
• /
• pp.15-26
• /
• 2004

The purpose of this study was to investigate the kinematic variables of peters motion in parallel bars. The subjects were 3 male national gymnasts. For this study, kinematic data were collected using video camera. Coordinate data were low-pass filtered using a fourth-order Butterworth with cutoff frequency of 6Hz. Each valuables analyzed was used to compare kinematic features between the subjects. The conclusions were as follows; 1. For a stable regrasp motion, the subjects appeared to increase horizontal and vertical displacement during the DS phase because it induce a vertical elastic of body and reaction of bar for the US phase. 2. For a stable hand standing motion of the regrasp, the subjects appeared to maintain the fast vertical and horizontal velocity during the DS phase, but in contrary during the US and Air phase the vertical and horizontal velocity appeared to do decrease. 3. When the arm lean angle and the trunk lean angle maintain a big angle during the DS phase, the subjects appeared to do a stable performance to release in a high position.

• Journal of Institute of Control, Robotics and Systems
• /
• v.10 no.10
• /
• pp.869-877
• /
• 2004

This paper deals with motion planning algorithm for kinematically redundant manipulators that are not fixed to the ground. Differently from usual redundant manipulators fixed to the ground, the stability issue should be taken into account to prevent the robot from falling down. The typical ZMP equation, which is employed in human walking, will be employed to evaluate the stability. This work proposes a feed forward ZMP planning algorithm. The algorithm embeds the 'ZMP equations' indirectly into the kinematics of the kinematic model of a manipulator via a ZMP stability index The kinematic self motion of the redundant manipulator drives the system in such a way to keep or plan the ZHP at the desired position of the footprint. A sequential redundancy resolution algorithm exploiting the remaining kinematic redundancy is also proposed to enhance the performances of joint limit index and manipulability. In addition, the case exerted by external forces is taken into account. Through simulation for a 5 DOF redundant robot model, feasibility of the proposed algorithms is verified. Lastly, usual applications of the proposed kinematic model are discussed.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1997.04a
• /
• pp.113-118
• /
• 1997

This paper presents the dimensional synthesis and kinematic analysis of the RSCS-SSP motion generating spatial mechanism using the displacement matrix method. This type of spatial mechanisms is used for the Mcpherson suspension in small automobiles. It is modeled for the wheel bump/rebound and steering motion. First, the suspension is modeled as a multiloop spatial rigid body guidance mechanism for the two major motions. Then the design equations for SSP, RS, and SC strut links are applied to synthesize an RSCS-SSP for up to three prescribed positions for the steering motiom from the suspension design specification. Thus a RSCS-SSP mechanism which is synthesized is also analyzed for the displacement during the steering motion.

• Korean Journal of Applied Biomechanics
• /
• v.16 no.2
• /
• pp.109-120
• /
• 2006

The purpose of this study was to examine the kinematical characteristics of gymnasts who can perform the KOVACS skill, and to grope for the better KOVACS Piked motion. The subjects were 3 male national gymnasts and were filmed with video cameras. And kinematic data were collected from the event of maximum knee flexion to the re-grasp the bar after airborne motion during KOVACS Piked motion. And the following conclusion were drawn; S1 took the enough time and inadequate height for performing KOVACS Piked motion. S2 showed the inadequate time and height during airborne motion with the large forward-backward and left-right movement. S3 showed the better KOVACS Piked movement among gymnasts, but the weak point of S3 was the large left-right shift. Based on the above conclusions, the gymnasts should be trained the enough time and height for the effective airborne movement and to reduce the left-right movement.

• PNF and Movement
• /
• v.20 no.1
• /
• pp.19-29
• /
• 2022

Purpose: The purpose of this study was to analyze the gait patterns of adults with intellectual disability and healthy adults based on collected kinematic data on the lower extremities and to investigate the gait patterns of intellectually disabled people by comparing the differences between the two groups. Methods: The participants were divided into in one group of healthy adults (n = 9) and one group with mild intellectual disabilities (n = 9). 3D motion analysis (Myomotion) was used to collect kinematic data from each group while the participants walked 3 times over 10 m. As a statistical method, each group's kinematic data during walking was analyzed and compared using an independent sample t-test. Results: Comparing the kinematic data of the lower extremities during walking between the group with mild intellectual disability and the healthy group, there were significant differences between the two groups in the hip and ankle joints in the stance and swing phases. Conclusion: The analysis suggests that people with intellectual disabilities have kinematic differences compared with healthy people. Based on the results of this study, it is necessary to conduct further research on rehabilitation programs for joint stabilization, exercise for increasing joint range of motion, muscle strengthening exercise, and proprioception training for people with intellectual disabilities with insufficient physical function.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.05a
• /
• pp.271-272
• /
• 2012