• Journal of Korean Society for Geospatial Information Science
• /
• v.10 no.5 s.23
• /
• pp.75-80
• /
• 2002

Depending upon geographical features and surrounding errors in the survey field, inaccurate positioning is inevitable in a kinematic DGPs survey. Therefore, a data inaccuracy detection algorithm and an interpolation algorithm are essential to meet the requirement of a digital map. In this study, GPS characteristics are taken into account to develop the data inaccuracy detection algorithm. Then, the data interpolation algothim is obtained, based on the feature type of the survey. A digital map for 20km of a rural highway is produced by the kinematic DGPS survey and the features of interests are lines associated with the road. Since the vertical variation of GPS data is relatively higher, the trimmed mean of vertical variation is used as criteria of the inaccuracy detection. Four cases of 0.5%, 1%, 2.5% and 5% trimmings have been experimented. Criteria of four cases are 69cm, 65cm, 61cm and 42cm, respectively. For the feature of a curved line, cublic spine interpolation is used to correct the inaccurate data. When the feature is more or less a straight line, the interpolation has been done by a linear polynomial. Difference between the actual distance and the interpolated distance are few centimeters in RMS.

• Korean Journal of Applied Biomechanics
• /
• v.15 no.3
• /
• pp.133-142
• /
• 2005

The purpose of this study was to compare of the kinematic variables from takeoff preparation to takeoff used by long jumpers who recorded over 8meters in 2002 Busan Asian Game and 2003 Daegu Universiade and 2001 national championship. The kinematic characteristics from the last three stride to takeoff at the takeoff board were analyzed such as velocities, heights and angles. The conclusion were as follows; In order to record over 8meters the national long jumpers should have under 5cm height variation at the penultimate stride of the run-up. In the approach phase the horizontal velocity of the jumpers should reach to 10m/s in touchdown at takeoff board The vertical velocity must have 3.75m/s simultaneously in order to record 8meters. The jumpers need to continue talent of the horizontal velocity in touchdown at takeoff board and require jumping power of the takeoff leg at takeoff board The appropriate body variation range ratio between takeoff and touchdown should be 1.2 vs 1 and the trunk angle at touch down on the board should be close to the erect posture for higher body flight.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2000.11a
• /
• pp.67-71
• /
• 2000

The wear behaviors of ultrahigh molecular weight polyethylene pins against titanium alloy and stainless steel disks moving in two different kinematic motion were investigated by conducting repeat pass rotational sliding and linear reciprocal sliding wear tests. Linear reciprocal motion wore more the polyethylene pin than did repeat pass rotational motion for both disk materials. It means that the repeated directional change of contact stresses generates more wear debris in polyethylene. For the linear reciprocal sliding tests, titanium alloy disks were damaged with some scratches after one million cycles but no surface damage was observed on the polyethylene pins. On the other hand, for the repeat pass rotational sliding tests, all titanium alloy disks were severely abraded on the entire region of sliding track. This phenomenon can be interpreted by that stress fatigue under repeated sliding contact initiated titanium oxide layer wear particles from disk surface, and these hard particles were embedded into polyethylene pin and then they severely abraded the disk surface. From these results it can be concluded that the kinematic motion in pin-on-disk wear tests play a crucial role on the wear behaviors of UHMWPE pins against titanium alloy and stainless steel disks.

• Water for future
• /
• v.22 no.4
• /
• pp.453-461
• /
• 1989

The analytical diffusion model is first formulated and its characteristics are critically reviewed. The flood events during the 1986-1988 flood seasons i the IHP Pyungchang Representative Basin are routed by this model and are compared with those by the kinematic wave model. The results showed that the analytical diffusion model simulates the observed flood events much better than the analytical kinematic wave model. The present model is proven to be an excellent means of taking the backwater effect due to lateral inflow or down river stage variations into consideration in channel routing of flood flows. It also requires much less effort and computing time at a desired station compared to any other reliable flood routing methods.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.12
• /
• pp.3871-3882
• /
• 1996

In this paper, a closed-form formulation for inverse kinematics of robot manipulators with kinematic redundancy under the constrained environment has been derived using the Kuhn-Tucker condition, the extended Lagrange multiplier method and the working set method. The proposed algorithm satisfies the necessaryand sufficient conditions for optimization subject to equality and inequality constraints. In addition, computationally efficient kinematic control methods have been proposed using differential kinemetics and gradient projection mehtod. The effectiveness of the proposed methods has been demonstrated with a 4-dof planar robot, and then a 7-dof spatial robot as a practical application to the nozzle dam task in the Nuclear Power Plant.

• Steel and Composite Structures
• /
• v.29 no.5
• /
• pp.669-680
• /
• 2018

The rapidly decreasing natural resources and the global variation of the climate push us to find intelligent and efficient structural systems to provide more people with fewer resources. This paper proposed a kinematic cable-strut system to realize sustainable structures in responding to changing environmental conditions. At first, the concept of the kinematic system based on crystal-cell pyramid (CP) cable-strut unit was given. Then the deployment of the structure was studied experimentally. After that, the static behaviors in the fully deployed state under the symmetric and asymmetric load cases were investigated. Moreover, the effects of thermal loading and the initial prestress distribution were also discussed. Comparative studies between the proposed structure and other deployable cable-strut system under three times of design load cases were carried out. Finally, the robustness of the system was studied by removal of one passive cable at one time.

• Journal of Korean Physical Therapy Science
• /
• v.27 no.3
• /
• pp.25-34
• /
• 2020

Background: Gait analysis is an important measurement for health professionals to assess gait patterns related to functional limitations due to neurological or orthopedic conditions. The purpose of this study was to investigate the reliability of the newly developed portable gait analysis system (PGAS). Design: Cross-sectional design. Test-retest study. Methods: The PGAS study was based on a wearable sensor, and measurement of gait kinematic parameters, such as gait velocity, cadence, step length and stride length, and joint angle (hip, knee, and ankle) in stance and swing phases. The results were compared with a motion capture system (MCS). Twenty healthy individuals were applied to the MCS and PGAS simultaneously during gait performance. Results: The test-retest reliability of the PGAS showed good repeatability in gait parameters with mean intra-class correlation coefficients (ICCs) ranging from 0.840 to 0.992, and joint angles in stance and swing phase from 0.907 to 0.988. The acceptable test-retest ICC was observed for the gait parameters (0.809 to 0.961), and joint angles (0.800 to 0.977). Conclusion: The results of this study indicated that the developed PGAS showed good grades of repeatability for gait kinematic data along with acceptable ICCs compared with the results from the MCS. The gait kinematic parameters in healthy subjects can be used as standard values for adopting this PGAS.

• PNF and Movement
• /
• v.9 no.4
• /
• pp.13-21
• /
• 2011

Purpose : The purpose of this study was to analyze the effect of closed kinematic chain exercise and proprioceptive neuromuscular facilitation exercise on the static dynamic balance performance of hemiplegic patients in order to suggest them therapeutic intervention methods. Methods : The subjects of this study were 18 hemiplegic patients grouped into 2 subgroups according to the exercise program. one group of closed kinematic chain exercise carried out sit to stand, Hooklying with pelvic lift(bridging) and stair-up & down by a hemiplegic leg. The other group of proprioceptive neuromuscular facilitation exercise carried out leg flexion-extension pattern in supine position, leg flexion pattern in standing and stabilizing reversal exercise in stating position. Each exercise was carried out over 3 sets of 10reps. Results : The results of this study were summarized as follows: 1. For both groups, there were statistically significant changes in the static balance (FICSIT-4) performance after exercise program (p<.05). 2. For both groups, there were statistically significant changes in the dynamic balance (FSST, TUG, FRT) performance after exercise program (p<.05). 3. In the comparison between both groups, there was no statistically significant difference in the static dynamic balance performance (FICSIT-4, FSST, TUGT, ER) after exercise program. Conclusion : As the results of the study shows closed kinematic chain exercise and proprioceptive neuromuscular facilitation exercise affect the improvement of hemiplegic patients'' static dynamic balance performance, it is supposed that these exercises could be therapeutic exercise program in clinical situations.

• Korean Journal of Applied Biomechanics
• /
• v.32 no.4
• /
• pp.147-152
• /
• 2022

Objective: The purpose of this study was to analyze the effects of club head and golf ball kinematics and body alignment according to the swing plane during golf driver swing. Method: Sixteen college golfers participated in this study. Kinematic data of the club head and golf ball were collected using golf swing analysis system (Trackman Ver. 3e). The body alignment variables were collected using 8 motion capture system. An Independent samples t-test was used for comparison between the Out-to-In group and In-to-Out group, and the statistical significance level was set at .05. Results: For the club head related variables, club path and club face angle showed higher values in Out-to-In swing plane than In-to-Out swing plane. For the kinematic variables of the golf ball, the total distance showed a higher value in the In-to-Out swing plane than that of the Out-to-In swing plane. For the body alignment, the In-to-Out swing plane showed higher values than the Out-to-In swing plane for the pelvis rotation angle and trunk rotation angle. Conclusion: This study suggest that it would be more effective to use the In-to-Out swing plane for increasing the total distance during the golf driver swing.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.19 no.3
• /
• pp.263-272
• /
• 2001

For a high resolution real-time kinematic GPS surveying using carrier phase, positioning accuracy according to the OTF initialization was better than 1 cm with more than 5-minute initialization within 20 km baseline. Also, it is recommended that measurements be carried out when PDOP and RDOP can be kept less than 4.0 since the geometrical layout of satellites has a great influence on the positioning accuracy. After considering the initial conditions and measuring time zone for real-time kinematic GPS. post-processed continuous kinematic GPS and real-time kinematic GPS measurements have been carried out. A new system has been proposed to store measured data by using a program developed to store GPS data in real time and to monitor the satellite condition through controller at the time of measurement. As a result, it has been revealed that possible noise in surveying could be corrected and the accuracy could be improved.