• Journal of Power Electronics
• /
• v.17 no.1
• /
• pp.305-313
• /
• 2017

A novel interference isolation method is proposed by using several designed coils in capacitive power transfer systems as isolation impedances. For each designed coil, its stray parameters such as the inter-turn capacitance, coil resistance and capacitance between the coil and the core, etc. are taken into account. An equivalent circuit model of the designed coil is established. According to this equivalent circuit, the impedance characteristic of the coil is calculated. In addition, the maximum impedance point and the corresponding excitation frequency of the coil are obtained. Based on this analysis, six designed coils are adopted to isolate the interference from power delivery. The proposed method is verified through experiments with a power carrier frequency of 1MHz and a data carrier frequency of 8.7MHz. The power and data are transferred parrallelly with a data carrier attenuation lower than -5dB and a power attenuation on the sensing resistor higher than -45dB.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.14 no.11
• /
• pp.1107-1114
• /
• 2004

Axial fans are widely used for automotive engine cooling device due to their ability to produce high flow rate to keep engine cool. At the same time, the noise generated by these fans causes one of the most serious problems. Especially, engine cooling fan noise in idle condition of a car is noticeable. Therefore. the high efficient and low-noise fan is seriously needed. When a new fan system is designed, system resistance and non-uniform inflow are the key factors to get the high performance and low noise fan system. In this study, aerodynamic and acoustic calculations are carried out on the automotive cooling fan and system. Effects of various design parameters are studied through the free wake analysis and experiments. Better performance and noise characteristic are obtained for the new design fan using the methodology. Furthermore through the modification of the fan system geometry parameters, the fan system produce more flow rate and become less noisy.

• Journal of Communications and Networks
• /
• v.6 no.3
• /
• pp.245-257
• /
• 2004

Driven by the growing number of the mobile subscribers, efficient channel resource management plays a key role for provisioning multimedia service in the next generation personal communication systems. To reuse limited channel resources, diminishing the coverage areas of cells seems to be the ultimate solution. Thus, however, causes more handover events. To provide seamless connection environment for mobile terminals and applications, this article presents a novel handover scheme called the intelligent channel reservation (ICR) scheme, which exploits the location prediction technologies to accurately reserve channel resources for handover connections. Considering the fact that each mobile terminal has its individual mobility characteristic, the ICR scheme utilizes a channel reserving notification procedure (CRNP) to collect adequate parameters for predicting the future location of individual mobile terminals. These parameters will be utilized by the handover prediction function to estimate the expected handover blocking rate and the expected number of idle channels. Based on the handover prediction estimations, a cost function for calculating the damages from blocking the handover connections and idling channel resources, and a corresponding algorithm for minimizing the cost function are proposed. In addition, a guard channel decision maker (GCDM) determines the appropriate number of guard channels. The experimental results show that the ICR scheme does reduce the handover-blocking rate while keeping the number of idle channels small.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• v.1
• /
• pp.175-180
• /
• 2006

This study is carried out the investigation of nonlinear characteristics of the ocean based on the field wave observation data acquired the western sea area in Jeju island during one year. It is aimed to offer the fundamental data for Freak wave forecasting in real sea. For this, the nonlinearity parameters of ocean waves, which are Skewness, Atiltness, Kurtosis and Spectrum band width parameter, are introduced, and the parameters are compared and discussed with some characteristic wave components, ie, significant wave height, maximum wave height, and so on.

• Structural Engineering and Mechanics
• /
• v.72 no.6
• /
• pp.747-762
• /
• 2019

Based on the ball-screw mechanism, a tuned viscous mass damper (TVMD) has been proposed, which has functions of amplifying physical mass of the system and frequency tuning. Considering the sensitivity of a single TVMD's effectiveness to frequency mistuning like that of the conventional tuned mass damper (TMD) and according to the concept of the conventional multiple tuned mass damper (MTMD), in the present paper, multiple tuned mass viscous dampers (MTVMD) consisting of many tuned mass dampers (TVMD) with a uniform distribution of natural frequencies are considered for attenuating undesirable vibration of a structure. The MTVMD is manufactured by keeping the stiffness and damping constant and varying the mass associated with the lead of the ball-screw type inerter element in the damper. The structure is represented by its mode-generalized system in a specific vibration mode controlled using the mode reduced-order method. Modal properties and fundamental characteristics of the MTVMD-structure system are investigated analytically with the parameters, i.e., the frequency band, the average damping ratio, the tuning frequency ratio, the total number of TVMD and the total mass ratio. It is found that there exists an optimum set of the parameters that makes the frequency response curve of the structure flattened with smaller amplitudes in a wider input frequency range. The effectiveness and robustness of the MTVMD are also discussed in comparison with those of the usual single TVMD (STVMD) and the results shows that the MTVMD is more effective and robust with the same level of total mass.

• BMB Reports
• /
• v.44 no.10
• /
• pp.692-697
• /
• 2011

To investigate the pathways of oxidoreductases in plants, 2 key components in thioredox systems i.e. thioredoxin h (Trx h) and NADPH-dependent thioredoxin reductase (NTR) genes were first isolated from tomatoes (Solanum lycopersicum). Subsequently, the coding sequences of Trx h and NTR were inserted into pET expression vectors, and overexpressed in Escherichia coli. In the UV-Visible spectra of the purified proteins, tomato Trx h was shown to have a characteristic 'shoulder' at ~290 nm, while the NTR protein had the 3 typical peaks unique to flavoenzymes. The activities of both proteins were demonstrated by following insulin reduction, as well as DTNB reduction. Moreover, both NADPH and NADH could serve as substrates in the NTR reduction system, but the catalytic efficiency of NTR with NADPH was 2500-fold higher than with NADH. Additionally, our results reveal that the tomato Trx system might be involved in oxidative stress, but not in cold damage.

• Korean Journal of Materials Research
• /
• v.26 no.8
• /
• pp.438-443
• /
• 2016

We developed an Al sputtering process by varying the plasma power, process temperature, and film thickness. We observed an increase of hillock distribution and average diameter with increasing plasma power, process temperature, and film thickness. Since the roughness of a film increases with the increase of the distribution and average size of hillocks, the control of hillock formation is a key factor in the reduction of Al corrosion. We observed the lowest hillock formation at 30 W and $100^{\circ}C$. This growth characteristic of sputtered Al thin films will be useful for the reduction of Al corrosion in the future of the electronic packaging field.

• ETRI Journal
• /
• v.29 no.6
• /
• pp.769-778
• /
• 2007

This paper proposes a multiplication algorithm for $F_{p^m}$, which can be efficiently applied to many pairs of characteristic p and extension degree m except for the case that 8p divides m(p-1). It uses a special class of type- Gauss period normal bases. This algorithm has several advantages: it is easily parallelized; Frobenius mapping is easily carried out since its basis is a normal basis; its calculation cost is clearly given; and it is sufficiently practical and useful when parameters k and m are small.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1998.03a
• /
• pp.304-309
• /
• 1998

In recent truck industry, ride quality improvement as well as payload capacity is a very important subject. In order to achieve this goal, it is necessary to study several sub-systems (powertrain, suspension, engine mount, exhaust, etc) of truck which are major components of vehicle. In this research, torsional vibration reduction method of 4$\times$2 truck powertrain is demonstrated by using computer simulation and experiment. First, truck powertrain is modeled as a vibration system and validity of developed model is verified by comparing free vibration results with experiment results. Second, Most key parameters which influence torsional resonance are examined utilizing mode analysis. Finally, frequency responses of truck powertrain are obtained and reduction counterplans of torsional vibration are suggested.

• Nuclear Engineering and Technology
• /
• v.56 no.9
• /
• pp.3740-3749
• /
• 2024

To reduce the losses caused by aging failure of insulation gate bipolar transistor (IGBT), which is the core components of nuclear power plant rod position indicating and rod control (RPC) system. It is necessary to conduct studies on its life prediction. The selection of IGBT failure characteristic parameters in existing research relies heavily on failure principles and expert experience. Moreover, the analysis and learning of time-domain degradation data have not been fully conducted, resulting in low prediction efficiency as the monotonicity, time correlation, and poor anti-interference ability of extracted degradation features. This paper utilizes the advantages of the stacked denoising autoencoder(SDAE) network in adaptive feature extraction and denoising capabilities to perform adaptive feature extraction on IGBT time-domain degradation data; establishes a long-short-term memory (LSTM) prediction model, and optimizes the learning rate, number of nodes in the hidden layer, and number of hidden layers using the Gray Wolf Optimization (GWO) algorithm; conducts verification experiments on the IGBT accelerated aging dataset provided by NASA PCoE Research Center, and selects performance evaluation indicators to compare and analyze the prediction results of the SDAE-LSTM model, PSOLSTM model, and BP model. The results show that the SDAE-LSTM model can achieve more accurate and stable IGBT life prediction.