• Journal of Welding and Joining
• /
• 제14권4호
• /
• pp.99-108
• /
• 1996

The microstructure and bond strength are examined on the SiC/SiC and SiC/mild steel joints brazed by the Ag-Ti based alloys with different Ti contents. In the SiC/SiC brazed joints, the thickness of the reaction layers at the bond interface and the Ti particles in the brazing alloy matrices increase with Ti contents. When Ti is added up to 9 at% in the brazing alloy. $Ti_3SiC_2$ phase in addition to TiC and $Ti_5Si_3$ phase is newly created at the bond interface and TiAg phase is produced from peritectic reaction in the brazing alloy matrix. In the SiC/mild steel joints brazed with different Ti contents, the microstructure at the bond interface and in the brazing alloy matrix near SiC varies similarly to the case of SiC/SiC brazed joints. But, in the brazing alloy matrix near the mild steel, Fe-Ti intermetallic compounds are produced and increased with Ti contents. The bond strengths of the SiC/SiC and SiC/mild steel brazed joints are independent on Ti contents in the brazing alloy. There are no large differences of the bond strength between SiC/SiC and SiC/mild steel brazed joints. In the SiC/mild steel brazed joints, Fe dissolved from the mild steel does not affect on the bond strength of the joints. Thermal contraction of the mild steel has nearly no effects on the bond strength due to the wide brazing gap of specimens used in the four-point bend test. The brazed joints has the average bond strength of about 200 MPa independently on Ti contents, Fe dissolution and joint type. Fracture in four-point bend test initiates at the interface between SiC and TiC reaction layer and propagates through SiC bulk. The adhesive strength between SiC and TiC reaction layer seems to mainly control the bond strength of the brazed joints.

• 대한소아치과학회지
• /
• 제23권2호
• /
• pp.559-574
• /
• 1996

The purpose of this study was to determine whether there was any correlation between temporomandibular joint dysfunction and structure of the mandibular condyle. Weanling rats had their masseter muscles resected and immunohistochemical findings were observed with a light microscope. The results obtained were as follows : 1. The condylar cartilage region was divided into articular, proliferating, cartilage cell and hypertrophic cell layers according to cell morphology. 2. In light microscopic views, the proliferating and cartilage cell layers of the experimental group decreased gradually and at the 8th week significantly. 3. In immunohistochemical staining for type I and II collagen, a reaction was detected in the lower part of proliferating cell and cartilage cell layers. In the cartilage cell layers, a stronger cellular reaction was present. Immunohistochemical staining for type II collagen reacted more strongly than that of type I collagen. 4. In immunohistochemical staining for proteoglycan, the staining of the experimental group resembled the control group and gradually showed a weak reaction. The proliferating and cartilage cell layers reacted more strongly than the hypertrophic cell layer. 5. In immunohistochemical staining for proliferating cell nuclear antigen(PCNA), the strong reaction was detected in the nucleus of the proliferating cell layer both in control and experimental groups. But the thickness of the proliferating layer decreased in experimental group, consequently the reaction of the experimental group was reduced more than that of the control group.

• Steel and Composite Structures
• /
• 제27권6호
• /
• pp.717-725
• /
• 2018

One of the most important design criteria in military tunnels and armoured doors is to resist the blast loads with minimum structural weight. This can be achieved by using steel sandwich panels. In this paper, the nonlinear behaviour of steel sandwich panels, with different core materials: (1) Hollow (no core material); (2) Rigid Polyurethane Foam (RPF); and (3) Vulcanized Rubber (VR) under free air blast loads, was investigated using detailed 3D nonlinear finite element models in Ansys Autodyn. The accuracy of the finite element model proposed was verified using available experimental test data of a similar steel sandwich panel tested. The results show the developed finite element model can be reliably used to simulate the nonlinear behaviour of the steel sandwich panels under free air blast loads. The verified finite element model was used to examine the different parameters of the steel sandwich panel with different core materials. The result shows that the sandwich panel with RPF core material is more efficient than the VR sandwich panel followed by the Hollow sandwich panels. The average maximum displacement of RPF sandwich panel under different ranges of TNT charge (1 kg to 10 kg at a standoff distance of 1 m) is 49% and 53% less than the VR and Hollow sandwich panels, respectively. Detailed empirical design equations were provided to quantify the maximum deformation of the steel sandwich panels with different core materials and core thickness under a different range of blast loads. The developed equations can be used as a guide for engineer to design steel sandwich panels with RPF and VR core material under a different range of free air blast loads.

• 대한조선학회논문집
• /
• 제47권6호
• /
• pp.821-830
• /
• 2010

Deck plates and hatch coming of large container carrier and offshore structures are joined by ultra-thick plates whose thickness is more than 60mm. Traditionally FCAW has been used to join the thick plates in butt joint. However, FCAW has been replaced with EGW since the welding efficiency of EGW is higher than that of FCAW. Tandem EGW using two electrodes has been applied to vertical position welding by several shipyards. EGW requires one or two layers of bead whereas FCAW requires more than 20 layers of weld bead in thick welding. However, high welding residual stresses are generated by EGW since it uses higher heat input than FCAW. In the present study, a finite element model is suggested to predict the residual stresses induced by the tandem EGW. Butt specimen of EH40 TMCP shipbuilding steel plates vertical welding was modeled by a three-dimensional model. Residual stresses were measured by X-ray diffraction method and to verify the numerical result. The results show a good agreement with experimental result.

• 한국안전학회지
• /
• 제29권4호
• /
• pp.9-14
• /
• 2014

Self-piercing riveting(SPR) is a mechanical fastening technique which is put pressure on the rivet for joining the sheets. Unlike a spot welding, SPR joining does not make the harmful gas and $CO_2$ and needs less energy consumption. In this study, static and fatigue tests were conducted using tensile-shear specimens with Al-5052 plates for evaluation of fatigue strength of the SPR joints. During SPR joining process for the specimen, using the current sheet thickness and a rivet, the optimal applied punching force was found to be 21 kN. And, the maximum static strength of the specimen produced at the optimal punching force was 3430 N. During the fatigue tests for the specimens, interface failure mode occurred on the top substrate close to the rivet head in the most high-loading range region, but on the bottom substrate close to the rivet tail in the low -loading range region. There was a relationship between applied load amplitude $P_{amp}$ and lifetime of cycle N for the tensile-shear, $P_{amp}=3395.5{\times}N^{-0.078}$. Using the stress-strain curve of the Al-5052 from tensile test, the simulations for fatigue specimens have been carried out using the implicit finite element code ABAQUS. The relation between von-Mises equivalent stress amplitude and number of cycles was found to be ${\sigma}_{eq}=514.7{\times}N^{-0.033}$.

• 한국운동역학회지
• /
• 제17권3호
• /
• pp.61-68
• /
• 2007

When an active muscle is stretched, its steady-state isometric force following stretch is greater than that of a purely isometric contraction as the corresponding muscle length, referred to as force enhancement (FE). The purpose of this study was to investigate possible effects of muscle architecture on the FE. While subject performed maximal isometric dorsiflexion (REF) and isometric-stretch-isometric dorsiflexion (ECC) contractions, ankle joint angle and dorsiflexion torque using a dynamometer and electromyography of the tibialis anterior and the medical gastrocnemius muscles were measure. Simultaneously, real-time ultrasound images of the tibialis anterior were acquired. Regardless of the speed of stretch of the ECC contractions. the torques produced during the isometric phase following stretch ($37.3{\pm}1.5\;Nm$ ($10{\pm}3%$ FE) and $38.3{\pm}1.5$ ($12{\pm}3%$ FE) for the ECC contractions with $15^{\circ}$/s and $45^{\circ}$/s stretch speeds, respectively) were greater than those of the REF contractions ($34.5{\pm}2.5\;Nm$). Moreover, the amount of FE was found to be stretch speed dependent. Angles of pennation ($\alpha$) during the isometric phase following stretch were the same for the REF ($15{\pm}1^{\circ}$) and the ECC ($14{\pm}1^{\circ}$(LS), $15{\pm}1^{\circ}$(LF)). During the same phase, muscle thicknesses were the same ($14.9{\pm}0.6$, and $14.9{\pm}0.5\;mm$ for the REF and the ECC contractions, respectively). For a large limb muscle, the tibialis anterior muscle, a similar amount of force enhancement was observed as did for other human skeletal muscles. Architectural variables, pennation angle and thickness, were not systematically different between the REF and ECC contractions when FE occurred. Therefore, the results of this study suggest that muscle architecture may have little influence on the production of FE.

• Archives of Plastic Surgery
• /
• 제34권1호
• /
• pp.64-69
• /
• 2007

Purpose: The key of treatment in syndactyly is to separate the fused digits safely, and to create a normal web space with enough cutaneous coverage. Despite many techniques have described the correction of syndactyly, skin graft still remains the annoying one. We designed the pentagonal flap from hand dorsum to reconstruct the web space reliably and try to minimize the need for skin graft. Methods: Between July 2003 and August 2005, six cases of syndactyly were corrected at UCLA Medical Center and Hallym University Sacred Heart Hospital using dorsal pentagonal flap for web space reconstruction and straight incisions for the sides of digits to minimize the need for skin graft. The proximal edge of the pentagonal flap was designed in V shape to allow for easy closure of the donor site after advancement. The pentagonal flap was advanced volarly with the underlying dermofat tissues to form a digital web. In some cases, skin defects were unavoidable and covered with full thickness skin graft from the inguinal area. Results: Syndactyly were seen in 4 cases of Apert syndrome, 1 postburn scar webbing with PIP joint contracture and 1 recurrence after the incomplete reconstruction. In all Apert syndrome, straight line incision was used along the sides of the fingers and skin graft was needed. But, in 2 cases of incomplete type, we could save the need for skin graft only for the correction of syndactyly. We could get a good looking web space without any complications such as flap or graft loss. Conclusion: As a modification of Sherif's V-Y dorsal metacarpal flap, we believe pentagonal flap could be one of the easiest and safest way to reconstruct the web space of syndactyly in functional and cosmetic standpoint.

• Journal of Korean Neurosurgical Society
• /
• 제60권4호
• /
• pp.441-447
• /
• 2017

Objective : Computed tomography (CT)-based method of three dimensional (3D) analysis ($MIMICS^{(R)}$, Materialise, Leuven, Belgium) is reported as very useful software for evaluation of OPLL, but its reliability and reproducibility are obscure. This study was conducted to evaluate the accuracy of $MIMICS^{(R)}$ system, and inter- and intra-observer reliability in the measurement of OPLL. Methods : Three neurosurgeons independently analyzed the randomly selected 10 OPLL cases with medical image processing software ($MIMICS^{(R)}$) which create 3D model with Digital Imaging and Communication in Medicine (DICOM) data from CT images after brief explanation was given to examiners before the image construction steps. To assess the reliability of inter- and intra-examiner intraclass correlation coefficient (ICC), 3 examiners measured 4 parameters (volume, length, width, and length) in 10 cases 2 times with 1-week interval. Results : The inter-examiner ICCs among 3 examiners were 0.996 (95% confidence interval [CI], 0.987-0.999) for volume measurement, 0.973 (95% CI, 0.907-0.978) for thickness, 0.969 (95% CI, 0.895-0.993) for width, and 0.995 (95% CI, 0.983-0.999) for length. The intra-examiner ICCs were 0.994 (range, 0.991-0.996) for volume, 0.996 (range, 0.944-0.998) for length, 0.930 (range, 0.873-0.947) for width, and 0.987 (range, 0.985-0.995) for length. Conclusion : The medical image processing software ($MIMICS^{(R)}$) provided detailed quantification OPLL volume with minimal error of inter- and intra-observer reliability in the measurement of OPLL.

• 지구물리
• /
• 제4권1호
• /
• pp.21-33
• /
• 2001

한반도의 일차원 지각구조모델 결정을 위하여 1991년부터 1998년까지 한국 기상청 지진관측망에 기록된 국지지진의 P-파의 도달시각자료에 대해 동시역산방법을 적용하였다. 역산에는 29개 지진의 178개 관측자료가 이용되었다. 한반도의 지각과 상부맨틀의 평균속도는 각각 6.3km/sec, 7.9km/sec 이며, 평균 지각 두께는 약 33km로 나타났다. 또한, 하부지각에 저속도층의 가능성을 보여주었다. 동시역산 방법은 진원요소, 관측소 보정치, 속도구조를 동시에 결정하기 위해 적용된다. 11개 관측소에 대한 관측소 보정치는 0～1.2sec 정도의 차이를 보인다. Synthetic data의 분석은 평균 지각 속도구조 뿐만 아니라, 진앙의 위치, 관측소 보정치가 신뢰할 만하다는 것을 보여준다.

• Journal of Ginseng Research
• /
• 제45권5호
• /
• pp.575-582
• /
• 2021

Background: In ginseng, there exists a glycolipoprotein complex with a special form of lipid LPAs called Gintonin. The purpose of this study is to show that Gintonin has a therapeutic effect on rheumatoid arthritis through LPA2 receptors. Methods: Fibroblast-like synoviocytes (FLS) were treated with Gintonin and stimulated with interleukin (IL)-1β. The antioxidant effect of Gintonin was measured using MitoSOX and H₂DCFDA experiments. The anti-arthritic efficacy of Gintonin was examined by analyzing the expression levels of inflammatory mediators, phosphorylation of mitogen-activated protein kinase (MAPK) pathways, and translocation of nuclear factor kappa B (NF-κB)/p65 into the nucleus through western blot. Next, after treatment with LPAR2 antagonist, western blot analysis was performed to measure inflammatory mediator expression levels, and NF-κB signaling pathway. Carrageenan/kaolin-induced arthritis rat model was used. Rats were orally administered with Gintonin (25, 50, and 100 mg/kg) every day for 6 days. The knee joint thickness, squeaking score, and weight distribution ratio (WDR) were measured as the behavioral parameters. After sacrifice, H&E staining was performed for histological analysis. Results: Gintonin significantly inhibited the expression of iNOS, TNF-α, IL-6 and COX-2. Gintonin prevented NF-κB/p65 from moving into the nucleus through the JNK and ERK MAPK phosphorylation in FLS cells. However, pretreatment with an LPA2 antagonist significantly reversed these effects of Gintonin. In the arthritis rat model, Gintonin suppressed all parameters that were measured. Conclusion: This study suggests that LPA2 receptor plays a key role in mediating the anti-arthritic effects of Gintonin by modulating inflammatory mediators, the MAPK and NF-κB signaling pathways.