• Earthquakes and Structures
• /
• v.17 no.4
• /
• pp.337-354
• /
• 2019

This paper presents the results of experimental and numerical studies conducted to investigate the behavior of exterior reinforced concrete beam column joints (BCJ) strengthened by using carbon fiber reinforced polymer (CFRP) sheets. Twelve reinforced concrete beam-column joints (BCJ) were tested in an experimental program by simulating the joints in seismically deficient old buildings. One group of BCJs was designed to fail in flexure at the BCJ interface, and the second group was designed to ensure joint shear failure. One specimen in each set was -retrofitted with CFRP sheet wrapped diagonally around the joint. The specimens were subjected to both monotonic and cyclic loading up to failure. 3D finite element simulation of the BCJs tested in the experimental program was carried out using the software ABAQUS, adopting the damage plasticity model (CDP) for concrete. The experimental results showed that retrofitting of the shear deficient, BCJs by CFRP sheets enhanced the strength and ductility and the failure mode changed from shear failure in the joints to the desired flexural failure in the beam segment. The FE simulation of BCJs showed a good agreement with the experimental results, which indicated that the CDP model could be used to model the problems of the monotonic and cyclic loading of beam-column reinforced concrete joints.

• Journal of Welding and Joining
• /
• v.16 no.1
• /
• pp.52-62
• /
• 1998

Laser beam welding of zinc-coated steel, especially lap joints, has a problem of zinc vapor produced during welding which has a low vaporization temperature of 906.deg. C. It is lower than the melting temperature of steel (1500.deg. C). The high pressure formed by vaporization of zinc during laser welding splatters the molten pool and creates porosities in weld. During laser lap welds of zinc-coated steel sheets with CW CO$_{2}$ laser the gap size has been analyzed and simulated using a FEM. The simulation has been carried out in the range of gap aetween 0 and 0.16 mm. The vaporized zinc gas has effected to prevent heat from conducting toward the bottom of sheets. In vaporized zinc gas has effected to prevent heat from conducting toward the bottom of sheets. In the case of too small gap size, zinc gas has not ejected and existed between two sheets. Therefore heat was difficult to conduct from the upper sheet to lower sheet and the upper sheet could over-melted. In the case of large gap size the zinc gas has been prefectly ejected but only a part of lower sheet has melted. The optimum range of gap size in the lap welds of zinc-coated steel sheets has been calculated to be between 0.08 and 0.12 mm. According to the comparison of experiment, the simulation is proved to be acceptable and applicable to laser lap welds.

• Journal of Environmental Health Sciences
• /
• v.34 no.1
• /
• pp.108-115
• /
• 2008

This study was performed to investigate the current status, in Korea, of the production of asbestos containing products (ACPs) such as asbestos cement products, asbestos friction materials, asbestos joint sheets, asbestos textile products, and other asbestos-containing products from May 2 to July 30, 2007. The information on ACPs was obtained through written questionnaires from 16 of the 27 companies that produce ACPs in Korea. The production amounts of asbestos containing gaskets were 70 tons in 2004, 90 tons in 2005, and 55 tons in 2006 in 4 companies and that of asbestos friction materials were 435.5 tons in 2004, 540.4 tons in 2005, and 454.3s ton in 2006 in 10 companies. The type and number of ACPs were:- 19 asbestos cement products, produced by 2 companies; 47 asbestos friction materials produced by 18 companies; 12 asbestos joint sheets productes by 4 companies; 18 asbestos textile products from 3 companies, and 6 other asbestos products from 5 companies. The database of ACPs was constructed to include the products name, identification number, name of company, production year, composition, asbestos content (%), usage, specification, and a picture. The database will be used to efficiently identify ACPs and to avoid asbestos exposure in workers and the general population.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• v.y2004m10
• /
• pp.39-44
• /
• 2004

A heat and room temperature construction method of asphalt have been mainly applying to rooftop waterproofing in concrete structure, and the rest construction method are sheet, membrane and mortar waterproofing construction method. In particular, joint method in sheet waterproof method is as overlap joint which on being reinforced with fiber and tape, have been applying for job site to mechanical fix using protection disk and anchorage and metal ironwork on the end of sheet. These construction method cause cutting off joint of sheet as behavior of structure according to repairs of sheet itself and thermal conduct, outdoor air environment. In conclusion, we analyzed and examined the application of various sheets and piece ashes about superior 'I' joint which divide from one and the other sheet and progressed about joint construction method of fixing method for overlap.

• Journal of the Korean Society of Safety
• /
• v.30 no.4
• /
• pp.1-7
• /
• 2015

Self-piercing riveting (SPR) process is gaining popularity due to its many advantages. The SPR does not require a pre-drilled hole and has capability to join a wide range of similar or dissimilar materials and combinations of materials. This study investigated the fatigue strength of self-piercing rivet joint with aluminum alloy (Al-5052) and steel (SPCC) sheets. Static and fatigue tests on tensile-shear specimens were conducted. From the static strength aspect, the optimal punching force for the specimen with upper SPCC (U.S) sheet and lower aluminum alloy(L.A) sheets was 34 kN. During static test the specimens fractured in pull-out fracture mode due to influence of plastic deformation of joining area. There was a relationship between applied load amplitude $P_{amp}$ and number of cycles N ; $P_{amp}=19588N_f^{-0.211}$ and $P_{amp}=4885N_f^{-0.083}$ for U.S-L.A and U.A-L.S specimens, respectively. U.A-L.S fatigue specimens failed due to fretting crack initiation around the rivet neck between upper and lower sheets.

• Transactions of Materials Processing
• /
• v.16 no.8
• /
• pp.603-613
• /
• 2007

This paper is concerned with joining of thin metal sheets by single stroke clinching process. This method has been used in sheet metal work as it is a simple process and offers the possibility of joining similar-dissimilar thin sheet metals. Clinching generates a joint by overlapping metal sheets deforming plastically by punching and squeezing sequence. AA 5754 aluminum alloy of 0.5 mm thick sheets have been selected as a modal material and the process has been simulated under different process conditions and the results have been analyzed in terms of the quality of clinch joints which are influenced mainly by tool geometries. The rigid-plastic finite element method is applied to analyses in this paper. Analysis is focused mainly on investigation of deformation and material flow patterns influenced by major geometrical parameters such as die diameter, die depth, groove width, and groove corner radius, respectively. To evaluate the quality of clinch joints, four controlling or evaluation parameters have been chosen and they are bottom, neck thickness of bottom and top sheets, and undercut thickness, respectively. It has been concluded from the simulation results that the die geometries such as die depth and diameters are the most decisive process parameters influencing on the quality of clinch joints, and the bottom thickness is the most important evaluation parameter to determine if the quality of clinch joints satisfies the demand for industrial application.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1996.03a
• /
• pp.159-164
• /
• 1996

For the purpose of establishing laser welding condition(laser power, welding speed and beam focus) and of evaluating tailor welded blank for three kinds of thin steel sheets of SPCC, SK5M and SUS304 using in the thin plate structure such as automobile, train and so on. Their $CO_2$ laser weldability were primarily tested under various welding condition. SPCC and SUS304 thin sheets showed good weldability under some welding condition. But, high carbon steel sheet SK5M needs heat treatment after welding to obtain higher tensile strength and ductility of the welded joint. And next, laser welding condition. Butt-welded specimens were not nearly broken at weld bead. However, base material were ruptured in the direction of circumference. The forming depths by tailor weld bead. However, base material were ruptured in the direction of circumference. The forming depths by tailor welded blank were SPCC+SPCC=22~25mm, SUS304+SUS304=25~43mm and SK5M+SK5M=13~17mm.

• Laser Solutions
• /
• v.15 no.1
• /
• pp.1-5
• /
• 2012

Recently ultra high strength steels(UHSS) has been widely applied to the structural or safety components in the automotive industry. Specially, hot stamping boron steel 22MnB5 has shown the crash-resistant characteristics when applying to bumpers and pillars. Lap joint Laser welding of the hot stamped and die quenched sheets of Boron steel was carried out using 3kW Nd/YAG laser. The appropriate Lap joint laser welding conditions were founded separately for four lap joint combinations. The lower sheest is a hot stamped sheet in common and the upper sheet is selected among the hot stamped steel and high strength steels such as SPCC, 370MPa, and 590MPa grade high strength steels. Cross bead sections and local hardening and softening were observed as well as tensile-shear test results.

• Journal of the Korea Institute of Building Construction
• /
• v.13 no.1
• /
• pp.38-47
• /
• 2013

When building with concrete in cold weather, an insulation method of heat curing must be determined, and a holistic curing plan that considers the characteristics of structures, the heat loss coefficient of a curing sheet, the joint condition of the curing materials and the quantity of heat produced by a heating apparatus is an essential prerequisite for protection against early frost damage. But on a number of national construction sites, there have been serious problems in cold weather concreting due to the unreliability of the information obtained from practical experience. In the construction field in Japan, there is a specification for heat curing prepared by Japanese Architectural Society, which provides an equation for calculating heat quantity. It is also necessary to adopt a detailed specification for a standard heat curing method that is applicable to all national construction sites. In this study, the effect of bubble sheets on the economic feasibility of cold weather concrete is investigated through a comparison with the blue sheets commonly prescribed in national construction sites. In conclusion, this study found that bubble sheets had the effect of reducing the cost of curing materials and the fuel cost consumed by a heating apparatus, compared to the use of blue sheets.

• Journal of Technologic Dentistry
• /
• v.36 no.3
• /
• pp.187-196
• /
• 2014

Purpose: This study aims to examine correlation between temporomandibular disorder and oral habits that have been known to cause temporomandibular disorder with both male and female undergraduates. Methods: To figure out correlation between temporomandibular disorder and oral habits, a survey was conducted to 500 students of two universities located in Daegu Metropolitan City and Gyeongsangbuk-do, and excluding the ones unreliably answered or indicating errors, total 427 (85.4%) out of 500 questionnaire sheets were used for final analysis. Results: Female students showed higher prevalence rates than male students in temporomandibular joint pain and temporomandibular joint clicking, and students having the lip biting habit, tongue thrust habit, or bruxism habit indicated a higher prevalence rate of temporomandibular joint pain than normal students. Also, students having the tongue thrust habit indicated a significantly higher prevalence rate of temporomandibular joint clicking than normal students not having it. And about trismus, students having the bruxism habit showed a significantly higher prevalence rate than normal students not having it. Conclusion: The findings imply that oral habits like lip biting, tongue thrust, or bruxism are closely related with temporomandibular joint pain, tongue thrust influences temporomandibular joint clicking, and bruxism does affect trismus.