• 한국산림과학회지
• /
• 제97권5호
• /
• pp.547-551
• /
• 2008

The study aimed to develop a cryopreservation method for long-term storage using mature somatic embryo of Japanese larch. In this study, desiccation treatments significantly affected re-induction rates of embryogenic tissue (ET) from dried somatic embryos. In the effect of different dehydration temperature and duration on the re-initiation ET. the highest frequency was shown when somatic embryos were dehydrated at $25^{\circ}C$ for 2 (45.5%) or 1 day (43.3%), respectively. In addition, low temperatures [$4^{\circ}C$, 2 days (44.2%) or 3 days (43.5%)] were marked higher ET initiation. After that, the initiation value was declined with dehydration duration. For comparison of different relative humidity on re-induction frequency of ET, the best re-induction (43.5%) was obtained from somatic embryos pre-dried at $(NH_4)_2SO_4$ (RH 79%). Both $Na_2HPO_4$ (RH 97%) and $Na_2CO_3$ (RH 88%) treatments were showed the similar rate, 34.6, 34.2%, respectively. However the lowest rate (19.6%) was observed in distilled water (RH 100%). In comparison of the various storage temperatures and duration of the dried somatic embryos, the highest frequency (66.9%) of re-initiation was obtained when somatic embryos were cryopreserved for one day. However, the frequency was gradually decreased as the time length of storage increased regardless of types of storage. None of ET re-initiated when stored at $4^{\circ}C$ for 1, 2 and 84 days.

• Journal of the Korean Wood Science and Technology
• /
• 제39권2호
• /
• pp.125-131
• /
• 2011

The characteristics of radio-frequency/vacuum drying Japanese larch boxed heart round logs with 150 mm and 210 mm in diameter and 2,500 mm in length, subjected to compressive loading, after the pretreatment of kerf were investigated. The results of this study were as the follows: The drying time of about 120 hours~130 hours was needed from green to about 15 percent of moisture content. The gradient of final moisture content for all specimens was very gentle in both longitudinal and transverse directions owing to dielectric heating. The surface checks seriously occurred although the occurrence extent of surface check for the kerfed specimens was slight compared with that for the control specimens because drying stress was relieved by kerf. The occurrence of surface checks for the L-specimen was more serious than that for the S-specimen.

• 임산에너지
• /
• 제20권2호
• /
• pp.41-45
• /
• 2001

본 연구는 목재에 폴리에틸렌글리콜(PEG)을 주입하였을 때 얻어지는 치수안정화 효과를 구명 하고자 수행하였다. 실험에 사용된 수종은 일본잎갈나무(낙엽송, Larix kaempferi)이었고, 분자량이 각각 1000, 1500, 4000, 6000인 PEG를 각각 30%, 40%, 50% 수용액으로 하여 함침 처리에 사용하였다. 치수안정성은 항팽윤율을 측정하여 평가하였다. PEG 주입에 따른 중량중가율은 PEG 처리 농도 40%가 가장 높은 값을 보였고, PEG 분자량 1500 처리가 가장 높은 값을 나타냈다. 또한, 평균 분자량 1500이상이 되면, 분자량이 커질수록 중량증가율은 감소하는 경향을 보였다. PEG 처리재의 항팽윤율(ASE)은 PEG #1000 또는 PEG #1500 처리시 접선, 방사방향 모두 가장 높은 값을 나타냈으며, PEG 분자량이 증가하면, ASE 값이 감소하는 경향을 보였다.

• Journal of Plant Biotechnology
• /
• 제36권3호
• /
• pp.230-235
• /
• 2009

The effect of auxin transport inhibitor (TIBA and PCIB) or auxin synergist (phloroglucinol) on somatic embryo maturation and germination in Japanese larch (Larix leptolepis) was examined. The addition of 15.8 mg/L ABA+5.0 mg/L PCIB showed most promoted the maturation of cotyledon -staged somatic embryos (177.7/90 mg ESM). In contrast, with treatment of 5.0 mg/L PCIB or 5.0 mg/L TIBA, no somatic embryos were obtained. Considering from this result, PCIB or TIBA alone could not substitute for exogenously supplied ABA for maturation of somatic embryos. In the test of below concentration of 5.0 mg/L PCIB, the highest results were recorded in 15.8 mg/L ABA+2.0 mg/L PCIB (109.3/90 mg ESM) or 15.8 mg/L ABA+5.0 mg/L PCIB (103.7/90 mg ESM). However, 5.0 mg/L phloroglucinol (0/90 mg ESM) or no ABA addition (3/90 mg ESM) had little influence on somatic embryos maturation. In germination study, the highest frequency of plantlet regeneration obtained from the somatic embryos which had matured on 15.8 mg/L ABA+5.0 mg/L PCIB (67.9%). However, either 5.0 mg/L PCIB nor 5.0 mg/L TIBA resulted in obtained from plantlets.

• Journal of the Korean Wood Science and Technology
• /
• 제33권2호통권130호
• /
• pp.8-16
• /
• 2005

In an effort to encourage the development of value added engineered applications for small diameter round timber, research is being conducted to develop and verify design guidelines for connections with specific application to round timbers. The objective of this research is to provide potential users with a number of viable connection options applicable in the fabrication of engineered, round wood structural components and systems. Target uses include trusses, built up flange beams and space frames. This paper presents information on a mortised steel plate connection fabricated using powder driven nails in 6 cm diameter Japanese Larch. The design load for PDN connections are around 1.3 kN per nail with strip and 0.8 kN per nail without stripe. The design model for PDN connectors could be chosen by the number of nails. If the number of nails are more than the critical number between nail bearing and wood failure, the wood failure model could be the way to design the structure safely. The wood failure model needs to be studied more but the model could be the tensile and cleavage mixed failure model.

• Journal of the Korean Wood Science and Technology
• /
• 제19권4호
• /
• pp.7-17
• /
• 1991

The feasibility of treating three softwood(Japanese larch pitch pine, and Korean pine) thinned logs by double-diffusion treatment processes was investigated. Some posts were incised before immersion, and others were imersed in hot copper sulfate solution. Comparison among species indicated that. in general, pitch pine was most treatable and Japanese larch least treatable. For all three species, almost all treatment schedules gave consistently good penetration and high net retention, but very steep gradient of preservative distribution. As expected, the treatability was increased by the extension of immersion time, increased concentration of treating solution, incising. and heating of the first solution. Of the variables tested, it appears that heating of the first solution is the most important. From the data in this paper, it may be concluded that, if the first solution is not heated, the best schedule is #3. If the first solution is healed. it appears the best schedules are #10 or #11. Since heating of the first solution improves the treatability. schedules # 10 or :#11 are recommended if the cost of heating might be justified. The data presented in this paper indicate that double-diffusion treatment processes seem to offer a promise as a comparatively effective and easy-operating method of treating thinned logs for the small-scale production of treated stock.

• 한국산림과학회지
• /
• 제96권2호
• /
• pp.151-159
• /
• 2007

This study was conducted to investigate the effects of thinning on changes in stand characteristics and understory vegetation in a silvopasture practiced Japanese larch plantation in the Research Forest of Kangwon National University, Korea. Three different thinning intensities (64%, 35%, and control) were applied. Before and after thinning, the understory plant species increased its number from 48 (7 tree species, 7 shrubs species, 28 herbaceous species, and 6 woody climbers) to 100 (11 tree species, 15 shrub species, 67 herbaceous species, and 7 woody climbers). Thinning made plants invade easily on the forest floor, and plot A (325 stems/ha) had much higher number of undersory species than those Of plot B (575 stems/ha) and control plot (1,150 stems/ha). In three years after thinning, understory aboveground biomass (kg/ha) of herbs were 523 for control, 1,230 for plot B, and 1,288 for plot A. The canopy coverage had remarkable influence on the understory biomass production, resulting in relatively small amount of herbage production on control plot. The differences were statistically significant between thinned plots and unthinned plot, but there were no significant differences among the thinned plots (p<0.05).

• 한국대기환경학회지
• /
• 제27권4호
• /
• pp.436-442
• /
• 2011

In this study, the Total Volatile Organic Compounds (TVOC) emitted from wood-based panels were compared by two analytical methods using the GC/FID and the GC/MS. Japanese Larch, Yellow Poplar, Particle Board (PB) and Medium Density Fiberboard (MDF) were selected as target materials. Major compounds emitted from the panels were Toluene, ${\alpha}$-pinene, ${\beta}$-pinene and limonene. In case of TVOC using GC/FID method, MDF E2 (1,497 ${\mu}g/m^3$) revealed the highest concentration among all wood-based panels, while Japanese Larch (1,772 ${\mu}g/m^3$) showed the highest value with respect to GC/MS method. Furthermore, it was found that the amount of VOC emitted from panels was different depending upon analytical methods. This significant difference was attributed to analytical sensitivities of GC/FID and GC/MS for various VOC. Besides, it was found that the composition ratios of main VOC compounds were not significantly different.

• Journal of the Korean Wood Science and Technology
• /
• 제36권6호
• /
• pp.88-95
• /
• 2008

내구성과 관련하여 구조부재의 수축문제가 목구조에서는 커다란 관심사가 되고 있다. 특히, 목재 소재를 적극 활용하는 전통공법에서는 짜맞춤 부위, 부재와 벽 등에서 발생하는 건조수축에 의한 갈라짐 등의 결함이 더욱 문제시되고 있다. 또한, 최근 기둥-보 공법에서 많이 사용되고 있는 국내산 낙엽송 집성재의 이용에 있어서도 함수율변화로 인한 수축과 팽윤에 대한 검토를 행할 필요성이 제기되고 있다. 낙엽송 소재와 접착층수를 달리한 낙엽송 집성재의 시험편에 대해 다양한 함수율상태에서의 치수변화율을 살펴보았다. 건조수축에 의한 치수변화 억제효과는 3층 이상의 접착층을 가지는 시험편에서 그 효과가 현저함을 알 수 있었다. 그리하여, 소재를 사용할 경우 최종사용조건에 맞추어 건조를 충분히 행하거나, 구조부재로 집성재를 이용함으로써 건조수축 문제를 어느 정도 해결할 수 있는 것으로 판명되었다.

• 한국산림과학회지
• /
• 제34권1호
• /
• pp.21-30
• /
• 1977

일본잎갈나무는 우리나라의 주요조림수종(主要造林樹種)으로 전국각지(全國各地)에 많은 조림지(造林地)와 임분(林分)이 있다. 이 수종(樹種)의 임분밀도관리(林分密度管理)의 지침(指針)을 마련하여 생산력예측(生產力豫則), 간벌계획(間伐計劃)과 수확량(收穫量) 사정(査定)을 용이하게 하는 일은 임업기술(林業技術)의 계량적(計量的), 생태적(生態的) 및 경제적(經濟的) 관점(觀點)에 대단(大端)이 의의있는 일로 생각 되었다. 이 연구(硏究)를 위해 정상적(正常的)으로 관리(管理)되고 있든 비정상적(非正常的)으로 관리(管理)되고 있든 최근(最近)에 간벌(間伐)한 흔적이 없는 임분(林分)에서 165개(個)의 표본(標本)을 조사(調査)하여 평균수고(平均樹高), 평균직경(平均直徑) 우세목수고(優勢木樹高), ha당(當) 본수(本數)와 1평균목(平均木)의 간재적(幹材積)을 산출(算出) 하였다. 이 연구(硏究)에 특(特)히 세장도이론(細長度理論)을 새로 도입(導入) 하였다. 이 이론(理論)에 대(對)한 실험적(實驗的) 검토(檢討)는 마(馬)와 Wardle, Shantz, Harms & Colline의 밀도시험결과(密度試驗結果)를 인용(引用)하여 증명한 바 있다. 임목(林木)의 상대생장(相對生長)은 일반적(一般的)인 logistic cnrve를 인용(引用)하고 공식(公式)은 모두 $Y=a{\times}b$를 대입(代入) 하였다. 각측정인자간(各測定因子間)의 관계(關係)는 아래와 같았다. 1. 세장도별(細長度別) 수고(樹高)와 밀고(密度)와의 관계(關係)-표(表) 1과 그림2 2. 세장도별(細長度別) 직경(直徑)과 밀도(密度)와의 관계(關係)-표(表) 1과 그림3 3. 세장도별(細長度別) 수고(樹高)와 단목간재적(單木幹材積)과의 관계(關係)-표(表) 3과 그림4 4. $D^2H$와 단목(單木) 간재적(幹材積)-$Log_eV=0.9569\;Log_eD^2H-9.8431$ 5. 밀도(密度)와 간재적(幹材積)-$Log_eV=9.5026-1.6800\;Log_eD$ 6. 밀도(密度)와 간재적(幹材積)-$Log_eV_{ha}=9.4911-0.6784\;Log_eD$ 7. 세장도별(細長度別) 수고계급(首告階級)에 응대(應對)한 간재적(幹材積)-표(表) 5 8. 세장도별(細長度別) 수고계급(首告階級)에 응대(應對)한 Ha당(當) 본수(本數)-표(表) 6 9. 세장도별(細長度別) 수고계급(首告階級)에 응대(應對)한 Ha당(當) 간재적(幹材積)-표(表) 7 이상(以上)의 과정(過程)을 거쳐 일본잎갈나무 임분밀도관리도표(林分密度管理圖表)를 제작(製作)하였다(그림 9). 이 관리표(管理表)의 정확도(正確度)를 검정하기 위하여 실측치(實測値)와 추정치(推定値)와의 관계(關係)를 보니 표(表) 8의 내용과 같이 오차(誤差)가 낮은편이었다. 이 도표(圖表)는 일본잎갈나무 임분(林分)의 밀도관리(密度管理)의 지침(指針)이 되리라 생각 된다.