• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1933-1938
• /
• 2004

Nucleate boiling experiments with constant wall temperature of heating surface were performed using R113 for almost saturated pool boiling conditions. A microscale heater array and Wheatstone bridge circuits were used to maintain a constant wall temperature condition and to measure the heat flow rate with high temporal and spatial resolutions. Bubble images during the bubble growth were taken as 5000 frames a sec using a high-speed CCD camera synchronized with the heat flow rate measurements. The geometry of the bubble during growth time could be obtained from the captured bubble images. The bubble growth behavior was analyzed using the new dimensionless parameters for each growth regions to permit comparisons with previous results at the same scale. We found that the new dimensionless parameters can describe the whole growth region as initial and later respectively. The comparisons showed good agreement in the initial and thermal growth regions. The required heat flow rate for the volume change of the observed bubble was estimated to be larger than the instantaneous heat flow rate measured at the wall. Heat, which is different from the instantaneous heat supplied through the heating wall, can be estimated as being transferred through the interface between bubble and liquid even with saturated pool conditions. This phenomenon under a saturated pool condition needs to be analyzed and the data from this study can supply the good experimental data with the precise boundary condition (constant wall temperature).

• Journal of Advanced Marine Engineering and Technology
• /
• v.9 no.3
• /
• pp.250-256
• /
• 1985

With the advant of thryistors having large peak inverse voltages, current-source inverters are becoming very popular to feed induction motors. But it is very difficult to analysis the commutation. Since the actual variation of current during commutation is neither instantaneous nor linear and is effected by many parameters. Minimized bias-time of reverse voltages during commutation is expressed in term of machine parameters, capacitor voltage, load current and so on. The minimized bias-time is computed with y and z and also the commuation mechanism is tested on 2.2 kw induction motor. The computed results are compared with the experimental results, and the results give a good information for designing the commutation mechanism.

• Nuclear Engineering and Technology
• /
• v.28 no.4
• /
• pp.379-389
• /
• 1996

To experimentally investigate the several wave patterns for the horizontal countercurrent stratified air-water flow, a series of systematic experimental studies have been performed. The experiments are carried out in a horizontal pipe with 4m in length and 102mm in inner diameter. The oater and air superficial velocities vary from 0.0004 to 0.0204 and from 0 to 6m/s, respectively. The instantaneous water thickness is measured by parallel-wire conductance probes, and the wave field is recorded by high speed video camera. Also, to evaluate the wave effect on interfacial friction factor, the pressure drop is measured. Statistical data anal)sis is accomplished in order to obtain the fundamental wave parameters such as un amplitude, length and velocity, and spatial growth factor. By using these statistical parameters, the wave regime boundaries can be verified.

• Journal of The Korean Astronomical Society
• /
• v.48 no.1
• /
• pp.9-20
• /
• 2015

We study the evolution of the energy spectrum of cosmic-ray electrons accelerated at spherically expanding shocks with low Mach numbers and the ensuing spectral signatures imprinted in radio synchrotron emission. Time-dependent simulations of diffusive shock acceleration (DSA) of electrons in the test-particle limit have been performed for spherical shocks with parameters relevant for typical shocks in the intracluster medium. The electron and radiation spectra at the shock location can be described properly by the test-particle DSA predictions with instantaneous shock parameters. However, the volume integrated spectra of both electrons and radiation deviate significantly from the test-particle power-laws, because the shock compression ratio and the flux of injected electrons at the shock gradually decrease as the shock slows down in time. So one needs to be cautious about interpreting observed radio spectra of evolving shocks based on simple DSA models in the test-particle regime.

• Journal of the korean Society of Automotive Engineers
• /
• v.14 no.4
• /
• pp.31-38
• /
• 1992

The objective of this study is to determine the ignition feasibility of a single shot, air-assisted gasoline fuel injector operated in a constant volume combustion chamber under atmospheric condition. A number of parameters has been selected for this experiments, such as dwelling time, spark gap position(r,z), spark electrode geometry, supplied air and fuel masses and spray cone deflector angle. On-site visual inspection of the instantaneous flame glow was chosen as one way to judge the successful ignition. In addition, chamber pressure and occasional photography were mobilized as for data recording. It was clearly observed that there was an entrainment air-fuel mixture toward spray axis from the spray formation and its development later on. The optimum ignition conditions were found for those parameters given above.

• Electrical & Electronic Materials
• /
• v.9 no.9
• /
• pp.891-899
• /
• 1996

A model for predicting the characteristics of elastic ferromagnetic materials having a moving gap was presented. Based on the model parameters concerning behavior of material, such as the instantaneous field intensity, attractive force between the poles, length of gap, and the induced current/ emf in the circuit can be determined from the numerical integrations of the governing equations derived. From the results of the model it is found that when dc emf is imposed on the circuit the current sharply rise and fall for very short duration then stabilize at extremely low level which depends mainly on elasticity, permeabilities and ratio of resistivity. Subsequently output emf is shown stabilized at constant value which depends on the previous parameters as well as the resistivity ratio of primary to secondary circuit after sufficient progress of time.

• Journal of the Semiconductor & Display Technology
• /
• v.19 no.4
• /
• pp.126-129
• /
• 2020

We introduce a lifetime assessment technique using deep learning algorithm with complex electrical parameters such as resistivity, permittivity, impedance parameters as integrated indicators for predicting the degradation of the organic molecules. The evaluation system consists of fully automated in-situ measurement system and multiple layer perceptron learning system with five hidden layers and 1011 perceptra in each layer. Prediction accuracies are calculated and compared depending on the physical feature, learning hyperparameters. 62.5% of full time-series data are used for training and its prediction accuracy is estimated as r-square value of 0.99. Remaining 37.5% of the data are used for testing with prediction accuracy of 0.95. With k-fold cross-validation, the stability to the instantaneous changes in the measured data is also improved.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.32 no.3
• /
• pp.87-101
• /
• 1990

The purpose of this study is to estimate the flood discharge and runoff volume at a stream by using geomorphologic parameters obtained from the topographic maps following the law of stream classification and ordering by Horton and Strahier. The present model is modified from Cheng' s model which derives the geomorphologic instantaneous unit hydrograph. The present model uses the results of Laplace transformation and convolution intergral of probability density function of the travel time at each state. The stream flow velocity parameters are determined as a function of the rainfall intensity, and the effective rainfall is calculated by the SCS method. The total direct runoff volume until the time to peak is estimated by assuming a triangular hydrograph. The model is used to estimate the time to peak, the flood discharge, and the direct runoff at Andong, Imha. Geomchon, and Sunsan basin in the Nakdong River system. The results of the model application are as follows : 1.For each basin, as the rainfall intensity doubles form 1 mm/h to 2 mm/h with the same rainfall duration of 1 hour, the hydrographs show that the runoff volume doubles while the duration of the base flow and the time to peak are the same. This aggrees with the theory of the unit hydrograph. 2.Comparisions of the model predicted and observed values show that small relative errors of 0.44-7.4% of the flood discharge, and 1 hour difference in time to peak except the Geomchon basin which shows 10.32% and 2 hours respectively. 3.When the rainfall intensity is small, the error of flood discharge estimated by using this model is relatively large. The reason of this might be because of introducing the flood velocity concept in the stream flow velocity. 4.Total direct runoff volume until the time to peak estimated by using this model has small relative error comparing with the observed data. 5.The sensitivity analysis of velocity parameters to flood discharge shows that the flood discharge is sensitive to the velocity coefficient while it is insensitive to the ratio of arrival time of moving portion to that of storage portion of a stream and to the ratio of arrival time of stream to that of overland flow.

• Journal of the Korean Geophysical Society
• /
• v.3 no.1
• /
• pp.37-48
• /
• 2000

In order to investigate in-line ground motions caused by earthquakes, we examine the multicomponent complex trace analysis method (MCTAM) for the synthetic data and apply it to real earthquake data. An experimental result for synthetic data gives correct information on the arrival times, duration of individual phases, and approaching angles for body waves. Rayleigh waves are also easily identified with the MCTAM. A deep earthquake with magnitude of 7.3 was chosen to test various polarization attributes of ground motions. For P waves, instantaneous phase difference between the vertical and the in-line horizontal components ${\phi}(t)$, instantaneous reciprocal ellipticity ${\rho}(t)$, and approaching angle ${\tau}(t)$ are computed to be ${\pm}180^{\circ},\;0{\sim}0.25,\;and\;-30^{\circ}{\sim}-45^{\circ}$, respectively. For S waves, ${\phi}(t)$ tends to vary while ${\rho}(t)$ have values of $0{\sim}0.3\;and\;{\tau}(t)$ remains near vertical, respectively. A relatively low frequency signal registered just prior to the S wave event is interpreted as a P-wave phase based on its polarization characteristics. Velocities of P and S waves are computed to be 8.633 km/s and 4.762 km/s, and their raypath parameters 0.074 s/km and 0.197 s/km. Dynamic Poisson's ratio is obtained as 0.281 from the velocities of P and S waves.

• Journal of Korea Water Resources Association
• /
• v.36 no.3 s.134
• /
• pp.399-411
• /
• 2003

An approach determining a confidence interval of Nash's observed mean instantaneous unit hydrograph is developed. In the approach, both two parameters are treated as correlated gaussian random variables based on the theory of Box-Cox transformation and the regional similarity relation, so that linear statistical parameter estimation is possible. A parametric bootstrap method is adopted to give the confidence interval of the mean observed hydrograph. The proposed methodology is also applicable to estimate the parameters of Nash's model for un-gauged basins. An application to a watershed has shown that the proposed approach is adequate to assess the uncertainty of the Nash's hydrograph and to evaluate parameters for un-gauged basins.