• ETRI Journal
• /
• v.43 no.3
• /
• pp.459-470
• /
• 2021

This paper presents a low-cost prototype for monitoring online the maximum power produced by a domestic photovoltaic (PV) system using Internet of Things (IoT) technology. The most common tracking algorithms (P&O, InCond, HC, VSS InCond, and FL) were first simulated using MATLAB/Simulink and then implemented in a low-cost microcontroller (Arduino). The current, voltage, load current, load voltage, power at the maximum power point, duty cycle, module temperature, and in-plane solar irradiance are monitored. Using IoT technology, users can check in real time the change in power produced by their installation anywhere and anytime without additional effort or cost. The designed prototype is suitable for domestic PV applications, particularly at remote sites. It can also help users check online whether any abnormality has happened in their system based simply on the variation in the produced maximum power. Experimental results show that the system performs well. Moreover, the prototype is easy to implement, low in cost, saves time, and minimizes human effort. The developed monitoring system could be extended by integrating fault detection and diagnosis algorithms.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.7 no.6
• /
• pp.34-41
• /
• 1993

This paper describes an effort to develop a microcomputer-based parameter identification system for three phase and two phase brushless DC motor. Back EMF equation is derived from back EMF waveform of three phase and two phase brushless DC motor. In this paper, a new identification algorithm for the brushless DC motor parameters by Pasek's technique is de veloped. It is found that Pasek's equation is valid for the brushless DC motor, too. The results obtained clearly shows that it is possible to implement the identification system for the determination of the brushless DC motor parameters. To minimize errors due to the ripple component in the measured armature current, dlgital averaging filter is employed. The whole identification process of signal generation, measuring, parameter determination is fully automated. The use of the pmpased method in the parameter identification system shows that the averaged current curve is in excellent agreement with the estimated current curve. Therefore, this close agreement conf i i the validity of this technique.

• The Bulletin of The Korean Astronomical Society
• /
• v.35 no.1
• /
• pp.32.2-32.2
• /
• 2010

The Korean Solar Radio Burst Locator (KSRBL) is a single dish radio spectrograph, which is designed to record the spectra of microwave (0.5 - 18 GHz) bursts with 1 MHz spectral resolution and 1 s time cadence, and locate their positions on the solar disk within 2 arcmin. It was installed at KASI in 2009 August, and operational thereafter. The antenna pointing coefficients were initially determined during the installation and refined later using a series of antenna pointing calibrations. The filter to prevent the radio frequency interference around 2 GHz was designed and is to be installed. After the installation, the full frequency coverage will be recovered from the temporarily restricted frequency coverage (5 - 14 GHz). Also an effort to solve a couple of minor problems for the full performance of the system is in progress.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.4B
• /
• pp.316-322
• /
• 2003

The office data for telecommunication switching systems included system configuration data, processing data, maintenance and administration data on a very large scale. Those data are dependent on functions of the system and the place of system installation. The effect of errors of office data is very serious. In order to reduce time and effort on the system development phase and to enhance system reliability, in this paper we proposed a data analysis and design method for automatically generating office data that are dependent on installation capability and system configuration of the swiching office.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.15 no.3
• /
• pp.74-82
• /
• 2001

To reduce the maintenance expense and the possibility of electric outage and/or accident, which causes the decrease in stability and reliability of transmission/distribution line, most of all, accurate measurement for the degree of contamination should be preceded. But the conventional method (brush wiping method), which is recommended in IEC 60815, has sow significant problem in the aspect of man power, expense, error, and so forth. In this investigation, we purpose the development of a new type automatic measuring apparatus, which could measure the degree of contamination on the surface of insulator in outdoor condition. To design and evaluate the apparatus, a FLUX 2D is used, and various laboratory tests, artificial contamination tests, were carried to proof the actual performance. With the result of these effort, we can get the meaningful conclusion to develope a new type automatic apparatus for contamination measurement.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.245-250
• /
• 2011

ERTMS/ETCS Level 1 ATP, ATC and ATS are Signaling Systems adopted in korea. For operating in three different trackside signaling systems, train must have individual onboard signaling systems, ATP, ATC and ATS. Three signaling systems in one train is the main cause to increase installation and maintenance cost. Also it is need more effort to change a onboard signaling system depend on the trackside signaling system. those things should lead to decrease efficiency of the onboard signaling system. one integrated onboard signaling system for ATP, ATC and ATS is the good solution for those problems. IOSS is an integrated Onboard Signaling System and still developing. In this paper, we introduce the methodology of model-based development of IOSS. IOSS has one superviser process and several functional blocks to process individual signaling system s. Rhapsody which is CASE tool is used to construct the structure and develop the software for IOSS.

• Korean Journal of Computational Design and Engineering
• /
• v.18 no.2
• /
• pp.83-92
• /
• 2013

IFC based open BIM has internationally developed as a solution for interoperability problem among different software applications. Despite much interest and effort, the open BIM technologies are rarely introduced to the construction industry and need more technical development for a practical application as well. This research aims to develop automated code checking modules for quality assurance process of BIM data. The research have analyzed domestic regulations focusing on super-tall buildings and developed open BIM-based code checking modules for the evacuation regulations. The modules are able to validate evacuation regulations such as installation of emergency elevator and fire safety zone. The authors expect to improve the process of BIM quality assurance and enhance the quality of BIM data by this research on automated checking system.

• Journal of the Korean Professional Engineers Association
• /
• v.33 no.4
• /
• pp.44-47
• /
• 2000

Recently number of reinstrumentation projects in the process plants has grown to meet the needs to modernize or upgrade the exsisting control systems in a bid to boost productivity and quality. Design, installation and start-up of these process automation systems can be successful and trouble-free only if decision points are addressed properly. The critical decision points are encountered from tile design through the start-up phases of implementing a modernization project and discussed extensively here on a practical basis. Key points are ;to assign a project manager out of the plant instrument engineers for him to organize and lead a project team. ;to follow three critical steps in designing and implementing. :to think ahead of the critical steps and to induce a positive cooperation from all level of participants in the effort to prevent possible schedule delays.

• Journal of the Korean Institute of Navigation
• /
• v.15 no.1
• /
• pp.67-93
• /
• 1991

In general, marine casualities take palace by the composite action of three elements such as waterway condition, vessel condition and man condition. One of the important characteristics of most marie casualties for small cargo vessels in maritime transportation of near-coastal and greater-coasting seas in that the same kind of casualities take place repeatedly in spite of the apprent causes, Because, it takes much time and effort for seamen to master waterway, vessel or operatin technique only to the practical and sensible level. In these days, with the development of our economy, our shiypping industry has grown and therefore the demand of marine officers has increased. This economic growth brought about undesirable situation like the evasion of seamen and frequent casualities of Korea vessels. These marine casualities are being caused mainly by the unskilfulness of operating technique as well as the bad waterway condition and ship's installation condition. Therefore, I conclude, in this paper, that the most efficient and economic preventing measures of marine casualities are seeking causes and removing them in advance under the close coperation system among all concerned parties.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.624-627
• /
• 1996

To provide pleasant building environment and the ease of maintenance and facility management, many new office buildings are being built as intelligent buildings. Building control systems which are employed in intelligent buildings require advanced types of controllers and varieties of control schemes. Designing and installation of these types of advanced building control systems take a lot of effort and also they are costly. In order to design these systems, it is necessary for the designers to have means to analyze and estimate the performance of control systems. The simulator which is presented in this paper is composed of three parts, HVAC simulation module, elevator simulation module, and evacuation modeling module for the outbreak of fire or similar disasters. In this paper, the functions and modelling method for each module are explained and simulation results are presented.