• Structural Engineering and Mechanics
• /
• v.77 no.6
• /
• pp.745-751
• /
• 2021

Concrete filled double skin tubular members (CFDST) consist of double concentric circular or square steel tubes with concrete filled between the two steel tubes. The CFDST members, having a hollow section inside the internal tube, are generally lighter than ordinary concrete filled steel tubular members (CFT) which have a solid cross-section. Therefore, when the CFDST members are applied to bridge piers, reduction of seismic action can be expected. The present study aims to investigate, experimentally, the behavior of CFDST stub columns with double concentric square steel tubes filled with concrete (SS-CFDST) when working under centric compression. Two test parameters, namely, inner-to-outer width ratio and outer square steel tube's width-to-thickness were selected and outer steel tube's width-to-thickness ratio ranging from 70 to 160 were considered. In the results, shear failure of the concrete fill and local buckling of the double skin tubes having largest inner-to-outer width ratio were observed. A method to predict axial loading capacity of SS-CFDST is also proposed. In addition, the load capacity in the axial direction of stub column test on SS-CFDST is compared with that of double circular CFDST. Finally, the biaxial stress behavior of both steel tubes under plane stress is discussed.

• Journal of the Korean Home Economics Association
• /
• v.35 no.4
• /
• pp.95-110
• /
• 1997

According to the design method for constructing the crotch angle of traditional Korean men's trousers there are differences in from after its completion. Since there is no standardization of visual & aesthetic pattern for the construction method which is stablished by the calculation formular of waist girth hip girth pantleg end and upper outer leg length it is difficult to be used for educational use or for teaching materials. Therefore the purpose of this project according to five models in proportion to the physical standard of Korea in ages from 24 to 29 years old is to establish a design criterion and the standardization of construction methods by introduction the pant construction method of the crotch angle by converting the sitting posture length to seaming crotch center point both knees width in the Korean way of sitting. The production method for the pattern design is as follow: (1) The waist girth formular is {{{{ { w} over {4 } }}}}+{{{{ {w} over {10 } }}}}(2) The hip girth formular is {{{{ {H } over { 4} }}}}+{{{{ {H } over {5 } }}}}(3) The pantleg end formular is {{{{ {H } over {4 } }}}}(4) A crotch angle is fixed at 70 degress.(5) The ratio of outer leg length to leg width is 5:8 (6) The component ratio of the upper outer leg length to the pant length in 5:8(7) The ratio of the division point of front / right inner leg length and left inner leg width to upper outer leg length is 5 : 8

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.4
• /
• pp.434-441
• /
• 2013

Bending motion has been used in the surgical instruments with bending structures and tendon mechanisms. A simplified bending angle amplification ratio between the proximal and distal bending joint was derived in this article. The bending structure of disk and rib in the proximal joint was analyzed based on finite element method with an emphasis on the circumferential uniformity of bending stiffness. Regarding the distal joint, optimal design and sensitivity analysis was done with four design variables of outer and inner diameter, rib height and rib width while maximizing the deformation under the stress distribution below the yield stress. Outer diameter and rib width are most critical to maximum deformation as the outer diameter and inner diameters are so to maximum equivalent stress.

• Journal of Electrical Engineering and Technology
• /
• v.8 no.6
• /
• pp.1424-1430
• /
• 2013

This paper presents design procedure of the magnetic bearings used for high-speed electric machines and flywheel energy storage systems. Magnetic bearing can be categorized by inner-rotor type and outer-rotor type according to the position of the rotary disc. These two types are applicable based on application environments such as application space, required attraction force, and controllability. Magnetic bearing is generally designed based on the ratio (geometrical coefficient or geometrical efficiency) of pole width to rotor journal radius but proper ratio is only decided by the analysis. This is the difficulty of the magnetic bearing design. In this paper, proper design technology of the inner-rotor type and outer-rotor-type eight pole magnetic bearings is introduced and compared with the FEM analysis results, which verifies the proposed design procedure is suitable to be applied to the design of the magnetic bearings for the industrial applications and flywheel energy storage system.

• Journal of the Korean Home Economics Association
• /
• v.39 no.10
• /
• pp.97-109
• /
• 2001

It is thought that a composition of trousers is related to fabrics with single breadth. Therefore, trousers are designed with pattern using this fabrics with single breadth. However, in the old pattern of trousers, the breadth of 33cm-35cm was not considered in designing patterns. In this context, deciding which pattern design is better is not easy as there are a variety of estimation methods. So in this study, standardization of drafting is pursued by an objective pattern design. For this, a base angle of the trouser closely relating to a form and function was measured and using the height and the base angle, a trouser pattern design was tried. For a measurement of the base angle, 5 subject were selected. They are 25-29 year-old male graduates with fine physical standard. The base angle was measured with symphysis pubis point as a standard when subjects sat with their legs crossed, when they stood with their legs open (not forced artificially) and when they laid down with their legs open. The distance between a knee inside joint and knees was measured three times and the resultant value was used for the pattern design. For a design of trousers, the height was applied and the base angle was fixed. As a pattern drawing, using the height, a base angle and circumference of the hip, a trouser was designed. The production method for the pattern design is as follow: (1) The length formula, is height + $\frac{height}{2}$ (2) The hip girth formula is $\frac{hipgirth}{2}$ - $\frac{hipgirth}{20}$(3) A crotch angle is fixed at $72^{\circ}$. (4) The ratio of outer leg length to leg width is 5 : 8. (5) The component ratio of the upper outer leg length to the pant length is 5 : 8. (6) The ratio of the division point of front right inner leg length and left inner width to upper outer leg length is 5 : 8.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.12 no.3
• /
• pp.2019-2028
• /
• 1970

1. Experiments were made for the efficient plowing method by the 4 wheel tractor, the results are as follow; 1) In case of plowing of inner side of the field, the efficient turning method to be the smallest turning time is the $\Omega$-shaped turning method in the turning distance less than 2r (r is the minimum turning radius of the tractor), and also, it is the U-shaped turning method in the turning distance larger than 2r. 2) 2.5r is most efficient in the unit turning section 'w' on plowing of the inner side of the field. 3) In case of plowing of outer side of the field, intermitted plowing method is efficient in case of W>-0.0345 L + 35.84, and also, semi-followed plowing method is efficient in case of W<-0.0345 L + 35.84. 4) The smaller the width of outer side of outer side of the field 'I' is, the higher is the plowing efficiency, and it is estimated that the minimum value 2r is suitable to 'I' in plowing of inner side and outer side of the field. 2. Study on the correlation between the unit field and plowing efficiencies obtained the following results; 1) plowing efficienies increase generally according as length-width ratio L/W and area A increase. 2) Percent of increase of plowing efficiencies decreases generally according as length-width ratio and area enlarge. 3) The limit that change of T is large owing to L/W is 6 for 20 a, 5 for 30 a, 4 for 50 a, 3 for 80 a, less than 2.5 for 100 a, generally, in L/W-T curve. 4) Rate of change of T-A curve is similar to rate of change of $T=A-\frac{2}{3}$ curve in spite of influence of L/W. 5) In case that length-width ratio is more than 3, effects of increase of 10 a area influenced upon plowing efficiencies are as much as effects of about 5 increase of length width ratio without correlation of size of the field. 6) In case that length-width ratio is 2 to 3, effects of increase of 10 a area influenced upon plowing efficiencies are as much as effects of about 4 to 2 increase of length-width ratio without correlation of size of the field, and the effects decrease according as not only length-width ratio decreases but also area increases, generally.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.18 no.2
• /
• pp.4096-4104
• /
• 1976

This experiment was carried out to investigate the efficient turning method which will be able to use every cutting methods, to calculate the width of the center field which must transpose from rotary cutting method to return cutting method, to investigate the effects of L/W and unit field on the operation efficiency. The results are summarized as follows: 1. In case of cutting in the outer field, the efficient turning method is the "$\alpha$" type turning method (half U-shaped turning method) at the first rotation, is the "$\beta$" type turning method (T-shaped turning method) at the second to fourth rotation. 2. In case of cutting in the inner field, the efficient turning method which takes the least turning time is the "a" type turning method ($\Delta$-shaped turning method). 3. The width of the center field (W') changes by the length-width ratio (L/W) and width (W), W' is 9.0m in case that L/W is 2.5 and W is 30m. 4. The larger L/W and area of unit field (A) become, the more operation efficiency (E) increases, and the limits that E is affected signicantly by L/W is 2 to 3.5 and A is within 5,000$m^2$. within 5,000$m^2$.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.23 no.6
• /
• pp.761-768
• /
• 1999

This paper is studied to find the optimum condition of double-inlet Sirocco fan installed in an indoor PAC for low noise operation by the Taguchi method. The goal of this study is to obtain the best combination of each control factor which results in a desired flowrate of Sirocco fan with minimum variability. In this study, the parameter design of the Taguchi method is adopted for robust design by the dynamic characteristic analysis using orthogonal arrays and S/N ratios. The flowrate measurements are conducted by using a multiple-nozzle-type fan tester according to the orthogonal array L9($3^4$). The results of this study can be summarized as follows ; (i) The optimum condition of control factor is a set of where A is an inner to outer diameter ratio($D_1/D_2$), B is a width to outer diameter ratio($L/D_2$), C is a blade attachment angle(${\theta}$) and D is a number of blade(Z), (ii) The flowrate under the optimum condition satisfies the equation $y=0.0384{\cdot}M$ where M is a signal factor, namely number of revolution. The flowrate performance improves about 7.3% more largely as compared with the current condition, which results in about 35RPM reduction of number of revolution for the target flowrate $18.5m^3/min$, and (iii) The sensitivity analysis shows that the major factors in contribution to flowrate performance are A, B, and D ; the percentage contributions of each control factor are 44.01%(Z), 26.77%($D_1/D_2$) and 20.42%($L/D_2$).

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.3
• /
• pp.269-277
• /
• 2010

In this paper, the design of a 0.5~2 GHz cavity-backed spiral antenna is described. Combined arm pattern with a log spiral in the inner region and an Archimedean spiral in the outer region, a backing cavity, and a Marchand coaxial balun for feeding are designed. Termination resistors are used to improve antenna characteristics at the lower frequency of the operation frequency. VSWR, axial ratio, gain and HPBW(Half Power Beam Width) characteristics are simulated using CST's MWS. Finally, the validity of these approaches is verified by comparing the simulated results with the measured ones. Also, the measurement results are compared with the performance of a commercial spiral antenna.

• Steel and Composite Structures
• /
• v.49 no.4
• /
• pp.441-456
• /
• 2023

Aiming at the development trend of light weight and high strength of engineering structures, this paper experimentally investigated the seismic performance of circular-in-square high-strength concrete-filled double skin steel tubular (HCFDST) stub columns with out-of-code width-to-thickness (B/t) ratios. Typical failure mode of HCFDST stub columns appeared with the infill material crushing, steel fracture and local buckling of outer tubes as well as the inner buckling of inner tubes. Subsequently, the detailed analysis on hysteretic curves, skeleton curves and ductility, energy dissipation, stiffness degradation and lateral force reduction was conducted to reflect the influences of hollow ratios, axial compression ratios and infill types, e.g., increasing hollow ratio from 0.54 to 0.68 and 0.82 made a slight effect on bearing capacity compared to the ductility coefficients; the higher axial compression ratio (e.g., 0.3 versus 0.1) significantly reduced the average bearing capacity and ductility; the HCFDST column SCFST-6 filled with concrete obviously displayed the larger initial secant stiffness with a percentage 34.20% than the column SCFST-2 using engineered cementitious composite (ECC); increasing hollow ratios, axial compression ratios could accelerate the drop speed of stiffness degradation. The out-of-code HCFDST stub columns with reasonable design could behave favorable hysteretic performance. A theoretical model considering the tensile strength effect of ECC was thereafter established and verified to predict the moment-resisting capacity of HCFDST columns using ECC. The reported research on circular-in-square HCFDST stub columns can provide significant references to the structural application and design.