• 태양에너지
• /
• 제7권2호
• /
• pp.65-73
• /
• 1987

Microstructural basis for the thermal degradation of electrodeposited black chrome "solar-L-foil" heated in air has been investigated using scanning electron microscopy, energy dispersive x-ray analysis, X-ray diffraction techniques and UV-VIS-NIR spectre-photometer. Experimental result, the change in the shape of the particle comprising the film from their initial needle like structure to a more spherical shape with an oxide after 1hr annealing at $600^{\circ}C$ has been observed. The effect is to degrade solar absorptance of the thin film.

• 한국멀티미디어학회논문지
• /
• 제7권11호
• /
• pp.1531-1539
• /
• 2004

본 논문은 입술의 경계선을 효과적으로 추출하는 방법을 제안하였다. 입술 형태는 PDM(Point Distribution Model)과 주성분 분석법을 이용하여 표현하고 입술 경계선은 GLDM(Gray Level Distribution Model)을 기반으로 표현하였다 입술 경계선 추출은 모델에 대한 입력영상의 정확도에 대한 목적함수를 최적화하는 문제로 단순화하였으며, 최적화를 위해 다운힐 심플렉스(Down Hill Simplex) 알고리즘을 이용하였다. 탐색과정에서 지역 최소점으로 수렴하는 문제를 해결하기 위하여 입술 형태 모델의 형태계수를 GMM(Gaussian Mixture Model)을 이용하여 표현하였다. 형태계수에 대한 GMM을 이용하여 입술의 대략적인 형태를 찾고, 이때 사용된 mixture 성분을 이용하여 탐색과정에서 입술의 형태를 조정함으로써 지역 최소점에 수렴하여 입술의 정확한 위치를 찾지 못하는 문제점을 해결하였다. 여러 영상을 대상으로 실험하여 좋은 결과를 얻었다.

• 드라이브 ㆍ 컨트롤
• /
• 제14권2호
• /
• pp.37-44
• /
• 2017

In this study, in order to prevent cavitation in a variable swash-plate type hydraulic pump, a basic model impeller has been applied to a new pump, and the impeller shape has been optimized through flow analysis. Based on the analysis results, we could propose an impeller shape with high efficiency and low possibility of cavitation in comparison with the basic model. The simplification of the basic shape of the impeller of the hydraulic pump was performed in three parts in the order of hub shape, wing, and curvature, and eight design parameters were defined to satisfy the design requirement. Compared with the initial model of the impeller, when the differential pressure of the optimum model increased, the efficiency was improved. It achieved the goal of design improvement because cavitation did not occur under the rated operating conditions.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1993년도 하계학술대회 논문집 B
• /
• pp.929-931
• /
• 1993

The design sensitivity analysis based on the finite element method is presented for the eddy current problem with a voltage source. Since, in this problem, the complex variable is used as the state variable, new approach to the sensitivity calculation for the complex variable system is required. Its result is applied to the design of the rotor slot shape of squirrel cage induction motor. As a analysis model, only one slot pitch of rotor is analyzed by using a Periodic boundary condition. The use of this minimal modelling method leads to much saving of calculation time. The design objective is to obtain the desired slip-torque characteristic. Because the shape of rotor slot has much influence on the slip torque characteristic, the design variables are taken on the interface shape between rotor core and rotor bar. The initial shape of rotor slot is the trapezoidal type with rounding corners. The obtained final shape is quite similar to the double squirrel cage type.

• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 2001년도 학술대회 논문집
• /
• pp.98-101
• /
• 2001

This work presents racetrack High Temperature Superconducting (HTS) magnet with iron plates to achieve the maximum current-carrying capacity and the simple shape that can easily be wound and jointed. The shape, position and kinds of iron plates are chosen by using 3 Dimensional Finite Element Analysis (3d FEA) considering magnetic saturation of iron plates. The racetrack HTS magnet with iron plates, magnet having optimized current distribution and initial magnet are compared with each other through 3D FEA, manufacturing and testing these magnets. The measured performance of the magnet with iron plates improved by 50% on the basis of initial magnet.

• 한국공간구조학회논문집
• /
• 제23권4호
• /
• pp.71-79
• /
• 2023

In this study, a prefabricated buckling brace (PF-BRB) was proposed, and a test specimen was manufactured based on the design formula for the initial shape and structural performance tests were performed. As a result of the experiment, all standard performance requirements presented by KDS 41 17 00 and MOE 2021 were satisfied before and after replacement of the reinforcement module, and no fracture of the joint module occurred. As a result of the incremental load test, the physical properties showed a significant difference in the stiffness ratio after yielding under the compressive load of the envelope according to the experimental results. It is judged necessary to further analyze the physical properties according to the experimental results through finite element analysis in the future.

• 대한조선학회지
• /
• 제22권1호
• /
• pp.21-30
• /
• 1985

This paper deals whth the buckling as well as postbuckling analysis of axisymmertric shells taking the initial deflection effects into account. Incremental equilibrium equations, based on the principle of virtual work, were derived by the finite element method, the successive step-by-step Newton-Raphson iterative technique was adopted. To define the transition pattern of postbuckling behavior from the prebuckling state more accurately, a simple solution method was developed, i.e. the critical load was calculated by the load extrapolation method with the determinant of tangent stiffness matrix and the equilibrium configuration in the immediate postbuckling stage was obtained by perturbation scheme and eigenvalue analysis. Degenerated isoparametric shell elements were used to analyse the axisymmetric shell of revolution. And by the method developed in this paper, the computer program applicable to the nonlinear analysis of both thin and moderately thick shells was constructed. To verify the capabilities and accuracies of the present solution method, the computed results were compared with the results of analytical solutions. These results coincided fairly well in both the small deflection and large deflection ranges. Various numerical analyses were done to show the effect of initial deflection and shape of shells on buckling load and postbuckling behavior. Futhermore, corrected directions of applied loads at every increment steps were used to determine the actual effects of large deflection in non-conservative load systems such as hydrostatic pressure load. The following conclusions can be obtained. (1) The method described in this paper was found to be both economic and effective in calculating buckling load and postbuckling behavior of shell structure. (2) Buckling and postbuckling behavior of spherical caps is critically dependent upon their geometric configuration, i.e. the shape of spherical cap and quantities of the initial deflection. (3) In the analysis of large deflection problems of shells by the incremental method, corrections of the applied load directions are needed at every incremental step to compensate the follower force effects.

• 한국강구조학회 논문집
• /
• 제11권4호통권41호
• /
• pp.409-416
• /
• 1999

반복하중을 받는 용접구조물의 피로수명 추정에 있어서 파괴역학을 이용한 피로균열 진전해석방법은 매우 유용하다. 휨응력을 받는 바닥강판의 피로균열 진전해석 문제에서는 균일한 축하중 하에서의 피로균열 진전해석 절차를 동일하게 적용할 수 있다. 본 연구에서는 휨응력하에서 피로균열 진전수명을 계산하는 방법을 제시하고 2차원 균열 문제에서의 피로균열 진전을 다루었다. 수치적으로 계산된 균열진전은 균열길이가 증가함에 따라 피로균열의 진전속도가 점차 감소하고 실험결과와 잘 일치하였다. 피로 수명은 초기균열길이와 균열형상에 따라 달라짐을 알 수 있었다.

• 한국자동차공학회논문집
• /
• 제11권3호
• /
• pp.138-144
• /
• 2003

Recently, the weight reduction of vehicle influences its environment problems and performances. It is a trend that a lot of parts have been currently changed to an aluminum alloy from steel materials. In this study, the shape optimization using an orthogonal array is performed to determine the design of the knuckle which is a part of suspension system. With the material of the weight reduction was achieved by satisfying the constraints of a strength requirement. The orthogonal array of $L_{18}$ is introduced to find the optimum design variables that considers the shape of the knuckle. The characteristic function composed of the objective and the construct is defined to the feasibility. Comparing to the weight of the initial design with steel materials that of optimum design with aluminum alloy material is reduced by 60%.

• 소성∙가공
• /
• 제18권8호
• /
• pp.589-595
• /
• 2009

The hot forming process of an exhaust CAM for vessel engine was designed by finite element(FE) simulation and experimental analysis. An aim of process design was to achieve the near-net shaped CAM forgings by hot forging process. Based on the compression test results of the low alloy steel, power dissipation map was generated using the the dynamic materials model(DMM). From the map, the initial heating temperature was determined as 1200oC. FE analysis was simulated to predict the formation of forging defects and deformed shape with different forging designs. Optimum process design suggested in this work was made by comparing with the CAM for vessel engine manufactured by actual forging process.