• Proceedings of the KIEE Conference
• /
• 1994.07a
• /
• pp.171-173
• /
• 1994

Magnetic wedge is proposed for improving the motor performance and to reduce the ripple of air gap flux. Carter's coefficient plays very important role when the ampere turns or exciting current is calculated. In this paper, we calculate the Carter's coe. by FEM taking into account the magnetic anisotropy of magnetic wedge in simple manner and analyze the effect of the wedge. And we analyze the slot leakage flux according to the wedge property.

• Proceedings of the KIEE Conference
• /
• 1992.07b
• /
• pp.692-694
• /
• 1992

This paper describes a robust flux bonging scheme which utilizes the windings of the machine itself to implement field orientation control of SLIM (Single-sided Linear Induction Motor). By subtracting the voltage across adjacent motor coils of the same phase which are named STATOR TAPPED COIL, a flux signal is obtained which is insensible to stater resister drop at a low speed that exerts a bad Influence on field orientation. The method using STATOR TAPPED COIL has been implemented at SLIM in our laboratory, and experimental results are being scrutinized.

• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.739-740
• /
• 2006

According to the rapid growth of high speed and precise industry, the application of synchronous motor has been increased. In the application fields, the large synchronous motor is not a self-starting motor. The rotor is heavy and, from a dead stop, it is impossible to bring the rotor into magnetic lock with the rotating magnetic field for this reason, all synchronous motor have some kinds of starting device. A simple starter is another motor which brings the rotor up to approximately 96 percent of it synchronous speed. The starting motor is disconnected and the rotor locks in step with the rotating field. The more commony used starting method is to have the rotor to include a squirrel cage indution winding. This indution winding brings the rotor almost to synchronous speed as an induction motor. So, this paper describes excessive condition interpretation of a exciter circuit to prevent starting failure of large synchronous motor. the large synchronous motor needs safety of it in accordance with operating frequent start and stop. the operating Problem point of synchronous motor appears potential element damage of Exciter circuit because synchronous motor is caused synchronous separation. hence we eliminate it and improve starting toque.

• Proceedings of the KIEE Conference
• /
• 1999.07a
• /
• pp.176-178
• /
• 1999

The Synchronous Reluctance Motor(SynRM) was made and experimented. Salient type SynRM was manufactured by cutting two sides of the three phase squirrel case rotor. So this prototype motor has same stator and capability with the counterparts of the induction motor. The airgap flux density, inductance and torque characteristics was inspected by Finite Element Analysis (FEA). The static torque experiments was accomplished. The paper proposed the effect of rotor bar by comparing two models.

• Proceedings of the KIEE Conference
• /
• 2003.11b
• /
• pp.31-34
• /
• 2003

There are several types of switching table for selection voltage vector in direct torque control of induction motor. In general, two-quadrant and four-quadrant operation switching table are used mostly. Two-quadrant operation has an advantage that reduced the torque ripples in comparison with four-quadrant operation, but it has the defect that is not constant average torque. Because the torque increasing slope size by non-zero voltage vector is different from the torque decreasing slope size by zero voltage vector as speed region. The main objective of this study is to maintain constant average torque using two-quadrant operation switching table. In proposed method, the torque increasing slope or decreasing slope are calculated before selected voltage vector is applied. Then, it is applied to zero voltage vector or non-zero voltage vector until the torque increasing slope and decreasing slope are equal. In total magnitude. Therefore it becomes to maintain average torque at whole operation speed. The validity of the proposed method is proven by simulated and experimental results.

• Proceedings of the KIEE Conference
• /
• 1994.07a
• /
• pp.579-581
• /
• 1994

The efficiency optimized speed control system of Induction Motor is proposed At light load, the IM has poor efficiency because of relatively high magnetizing current. In this paper, by employing the field oriented control with flux controller which the motor is operated at optimal slip frequency, the proposed system has good performance and high efficiency. In simulation, the performance, loss and efficiency of the proposed optimal flux control system are compared with those of the coventional constant flux operation. In conclusion, the efficiency is raised by 2.55%, the loss is decreased by 0.1[p.u].

• Proceedings of the KIEE Conference
• /
• 1992.07b
• /
• pp.1242-1244
• /
• 1992

This Paper deals with a Auto-Tuning Fuzzy PID Controller used in real time and its application for induction motor. The control strategy of the controller is able to develop and improve automatically. The new Auto-Tuning Fuzzy PID Control algorithm which modifies the fuzzy control decision table is presented in this paper. It can automatically refine an initial approximate set of fuzzy rules. The possibility of applying fuzzy algorithms in faster response, and more accurate was compared with other industrial processes, such as AC Motor driver. The performance of Proportional_Integral Derivative(PID) control and this fuzzy controllers is compared in terms of steady_state error, settling time, and response time. And then, Limitations of fuzzy control algorithms are also described.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1059-1060
• /
• 2007

In this paper analysis of the characteristics in the three phase induction motor for the electric forklift truck is researched. There are two kinds of the Finite element analysis method. First thing is time domain analysis by the time transient method. Second thing is frequency domain analysis by method which assumes applied voltage and current sinusoidal. Especially in case of the characteristic studies, electromagnetic analysis is performed about each prototype motors. The obtained results are compared and the result of the test is examined. We could know characteristics of each prototypes and verify the design program of the motor through FEM. Finally this paper shows the factors of discord results of the analysis.

• Journal of international Conference on Electrical Machines and Systems
• /
• v.3 no.2
• /
• pp.126-131
• /
• 2014

This paper discusses stability of new simplified sensorless vector control systems of induction motors (IM). The simplified sensorless systems estimate the flux angle by using the output voltage of d-axis PI current controller to achieve the q-axis flux zero. Two simplified sensorless systems are studied. The difference of two systems is the presence or absence of a q-axis PI current controller. The systems stability is compared by deriving linear state equations and showing root loci and unstable regions. Furthermore, transient responses and experiment results make clear the stability of the proposed system.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.11
• /
• pp.1829-1838
• /
• 1989

This paper is proposed one method of the exact optimal switching pattern of Selected Harmonic Elimination(SHE) Pulse Width Modulation(PWM). It defined Harmonic Elimination Band (HEB) at Constant Voltage(CV) and sought all solutions which are included HEB. Then, it calculated the Generalized Klirr Factor(GKF) beling to this solution and decided the optimal switching pattern which is minimized GKF. This optimal switching solution is used as initial condition of Newto Raphson(NR) method of decided easily switching pattern at Variable Voltage(VV). We desined the inverter by Power Transister(PTR) and implemented variable speed drive of Induction Motor(IM) in order to verify the validity of this theoretical proposition, then shown this results by comparison and analysis.