• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.12
• /
• pp.54-62
• /
• 2003

A systematic synthesis process is described lot the simulation of current-controllable inductors using operational transconductance amplifiers (OTAs). The process is used to obtain three circuits; two are believed It) be novel. The process is also applied to design current-controllable frequency-dependent negative resistances (FDNRs). Operation principles of designed circuits are presented and experimental results are used to verify theoretical predictions. The results show close agreement between predicted behavior and experimental performance. The application of a FDNR to a current-controllable band-pass filter is also presented.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.256-259
• /
• 2003

In this paper, a design of multi-layered BPF(bandpass filter) using LTCC(Low Temperature Co-fired Ceramic) process by a lumped-elements is proposed for SOP(system-on-a-chip) of wireless communication systems. The proposed BPF improved a characteristic of rejection band to build an attenuation pole caused by structurally adjacent co-inductance and coupling. The simulation data shows a bandwidth of 90MHz from a center frequency of 2.4GHz, a return loss of 27dB, an insertion loss of 3.2dB, and an attenuation of at least 20dBc at $f_0{\pm}250MHz$. Simulations have used serenade circuit simulation and HFSS EM simulation.

• Proceedings of the KIEE Conference
• /
• 1997.07e
• /
• pp.1642-1644
• /
• 1997

The simulation study of lightning faults reducing effects by the installation of surge arresters on the 154 kV transmission line is stated here. For the purpose of detailed simulation of arcing horn, a flashover model with dynamic characteristics of arcing horn gap was represented as a non-linear inductance which is controlled by EMTP/TACS(Electromagnetic Transient Program/fransient Analysis of Control Systems) switches. The back flashover inducing current was increased from 50 kA to 88 kA by the installation of surge arresters on the transmission line which has one ground wire and 20 ohms of tower footing resistances. The great advantage of surge arrester installation on one circuit of the double circuit transmission line is to prevent the simultaneous back flashover up to 190 kA.

• Proceedings of the IEEK Conference
• /
• 2000.07b
• /
• pp.1119-1122
• /
• 2000

This paper describes on RF circuit simulation technique, especially on a RF modeling and a model extraction of a LDMOS(Lateral Diffused MOS) that has gate-width (Wg) dependence. Small-signal model parameters of the LDMOSs with various gate-widths extracted from S-parameter data are applied to make the relation between the RF performances and gate-width. It is proved that a source inductance (Ls) was not applicable to scaling rules. These extracted small-signal model parameters are also utilized to remove extrinsic elements in an extraction of a large-signal model (using HP Root MOSFET Model). Therefore, we can omit an additional measurement to extract extrinsic elements. When the large-signal model with Ls having the above gate-width dependence is applied to a high-power LDMOS module, the simulated performances (Output power, etc.) are in a good agreement with experimental results. It is proved that our extracted model and RF circuit simulation have a good accuracy.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.49 no.8
• /
• pp.514-521
• /
• 2000

This paper presents a direct thrust control scheme for permanent magnet linear synchronous motor(PMLSM) by using digital signal processor(DSP). And a simulation method for the direct thrust control of a permanent magnet linear synchronous motor using the equivalent circuit is presented. The detent force that was obtained by cubic spline method is considered in the simulation. Thrust correction coefficient is utilized to estimate actual thrust on the direct thrust control, which considers the longitudinal end effect due to the finite core length of the permanent magnet linear synchronous motor. The motor self inductance, the initial flux linkage by the permanent magnet is calculated in advance by the finite element analysis, and then the direct control simulation is carried out. As the results, thrust, current and speed are shwon.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11a
• /
• pp.418-421
• /
• 2001

The ceramic filters were developed using technology similar to that of quartz crystal and electro- mechanical filter. However, the key to this development involved the theoretical analysis of vibration modes and material improvements of piezoelectric ceramics. The primary application of ceramic filters has been for consumer-market use. Accordingly, a major emphasis has involved mass production technology, leading to low-priced devices. A typical ceramic filter includes monolithic resonators and capacitors packaged in unique configurations. Nakazawa developed a double-mode resonator as two acoustically coupled single resonators. And he developed 10.7MHz crystal filters using multi-energy trapping mode of thickness shear vibration. He succeeded in realizing a two-pole band pass filter response without external inductance by splitting a dot electrode to creak coupled symmetric and anti- symmetric vibration modes. Accordingly, the simulation for ceramic (inter were important. So that, this paper were investigated the pass frequency of filter on the electrode length and thickness of ceramic.

• Proceedings of the KIPE Conference
• /
• 2016.07a
• /
• pp.285-286
• /
• 2016

This paper proposes a method for designing the inductor to minimize power loss for boost converter. The proposed inductor design method uses genetic algorithm to find an optimal inductance and an optimal frequency which minimize the power loss at rated power. The validity of proposed inductor design method is verified by simulation and experiment.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.8
• /
• pp.1523-1528
• /
• 2011

This paper proposes buck-type charging method using motor inductance, 3-phase inverter and bi-directional converter without an additional charger in plug-in hybrid electric vehicles. The proposed system has advantages over the conventional system such as high charging efficiency, high power factor, and low total harmonic distortion. The validity of each methods are verified by theoretical analysis and simulation.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2002.11a
• /
• pp.19-21
• /
• 2002

Electroded lamps operated at a high enough frequency can usually be modeled for the purpose of ballast design, as a resistor. Electrodeless fluorescent lamps include other components such as the arc tube's inductance. But that's impedance is small and so will be neglected in this paper. So, electrodeless fluorescent lamps is modeled as a resistor. A SPICE compatible model was developed for an electrodeless fluorescent lamp(OSRAM SYLVANIA ICETRON/ENDURA 150W).

• Proceedings of the KIPE Conference
• /
• 2014.11a
• /
• pp.75-76
• /
• 2014

This study deals with a isolation type MIC(Module Integrated Converter) for AC module with advantages such as DC Wireless, freely selectable installation capacity, minimized shadow effect etc. In this paper, MIC circuit with the function which can remove the ripple voltage of PV module and give the discharging path for charged energy in leakage inductance of isolation transformer. The validity of proposed circuir is verified by the simulation with PSIM.