• Journal of the Korea Convergence Society
• /
• v.9 no.2
• /
• pp.1-6
• /
• 2018

In this study, the investigation results of conducted and radiated emission for DC/DC converter circuit applied in electric vehicles are presented. A frequency spreading circuit was used to improve the EMI characteristics of a power converter designed by using MPQ4433 chip. The frequency spreading circuit using a TLV3201 chip was designed and applied to the power converter. A PCB was fabricated based on the EMI minimization procedures and simulated and measured results were presented for the far-field and near-field conducted and radiated emissions using the fabricated circuit. The measurement were done as CISPR 25 standardized test procedures. It is clearly showed that the EMI characteristics were improved 20% in case frequency spreading was applied. The EMI reduction technique using the frequency spreading proposed in this study was first applied to the design of power converter module for automobile. It is expected that the method presented here can be effectively used for EMI improvement in the future.

• Journal of Advanced Navigation Technology
• /
• v.28 no.3
• /
• pp.309-314
• /
• 2024

Avionics Intercom performs communication between pilot, co-pilot and crews in aircraft. In the case of developing intercom in the aircraft modification development project, additional communication equipment or avionics equipment is configured to link the existing intercom with the headsets. Newly designed intercom needs a configuration that receives an aircraft headset microphone and transmits a microphone signal to the existing intercom, and these signals are required to perform signal quality above a certain level. To satisfy these requirements, microphone transmitter circuit has designed and tested, but quality factors of signal were not suitable. In order to avoid the issue, eliminate transmitter and apply signal bridge circuit considered with load effect, and it meets requirements. In this paper, the test results for the signal quality for each configuration are reviewed.

• Fire Protection Technology
• /
• s.28
• /
• pp.48-54
• /
• 2000

The technique detects radiant energy form a flaming fire of fuels contained carbonaceous material can be applied to fast growing fires. This technique applied detectors are ultimately effective when early detecting fire alarm system is required or the smoke and heat detectors can not applied. In Korea Fire regulation, a flame detector should be install in case that the installation height is higher than 20[m], chemical plant, hangar refinery. Therefore it is really necessary that a flame detector has to be developed as soon as possible. With foundation technique of flame detector, ideal sensing element and stable circuit design, a trial UV flame detector is manufactured. The stable and reliable technique of flame detector is established through the repeateed perfomance test and modification. An early detecting fire alarm device is developed through the modification, supplement of the structure and circuit. Results of the R & D for the manufacture of an excellent flame detecting device is carried out with the establishment of technique for the mass production and the qualified manufacturing process.

• Journal of Power Electronics
• /
• v.15 no.3
• /
• pp.830-840
• /
• 2015

The H-bridge inverter is the fundamental power cell of the cascaded distribution static synchronous compensator (DSTATCOM). Thus, cell reliability is important to the compensation performance and stability of the overall system. The concept of the power electronics building block (PEBB) is an ideal solution for the power cell design. In this paper, an H-bridge inverter-based “plug and play” HPEBB is introduced into the main circuit and the controller to improve the compensation performance and reliability of the device. The section that discusses the main circuit primarily emphasizes the design of electrical parameters, physical structure, and thermal dissipation. The section that presents the controller part focuses on the principle of complex programmable logic device -based universal controller This section also analyzes typical reliability and anti-interference issues. The function and reliability of HPEBB are verified by experiments that are conducted on an HPEBB test-bed and on a 10 kV/± 10 Mvar DSTATCOM industrial prototype.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.343-347
• /
• 2004

As a first demonstration of proven stability for a-Si, over 7000h of stability data for a high drive current a-Si AMOLED pixel driver circuit was presented at SID 2004. Also demonstrated was an AMOLED display operating at 6V using the IGNIS 4-T pixel driver circuit [1] and based on a top-emission reverse OLED architecture. In this paper, an update to that information is presented with test data that is representative of lifetime in excess of 25,000 hours taking into account pertinent acceleration factors, extracted from high current drive and high temperature stressing conditions. Lifetimes will continue to increase, given the high and ever-increasing OLED efficiency.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.52 no.5
• /
• pp.230-237
• /
• 2003

Current mode control has been used for DC to DC converters for over twenty years. There are many different control schemes which use the inductor current signal in one way or another to control the DC to DC converter. In this paper, the state space averaging technique is applied for the analysis of flyback type current mode control circuit. We made real converter for the guarantee of stable output characteristic and proper design of feedback circuit. The validity of proposed method is verified from test result. The improvement of stability is confirmed by sinusoidal signal injection method with isolated transformer. It is known that phase margin is sufficient and gain crossover frequency fc is early 1/5 of switching frequency, fs, from the experimental result with frequency response analyzer.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.5 no.3
• /
• pp.553-561
• /
• 2001

Chua's oscillator is a simple electronic circuit which exhibits a variety of bifurcation phenomena and attractors, It consist of two capacitors, an inductor, two linear resistors, and a nonlinear resistor. When the circuit exhibits chaotic signals, the nonlinear resistor of Chua's oscillator may have six different voltage - current characteristics. In this paper, the design methodology for practical implementation of the nonlinear resistors which have all these characteristics is described. In addition, the effectivness of result is shown by not only the computer simulation but also the experimental test.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.221-224
• /
• 1996

Since impact phenomenon is highly nonlinear, the analysis and control of the contact motion has been a challenging subject. Various researches have been carried out mostly for the contact of a rigid robotic manipulator with a stiff and elastic environment. This paper is motivated by a new contact task: the in-circuit test of a printed circuit board. In this process, high speed contact occurs between a rigid probing manipulator and a plastically deformable work environment. A new dynamic model of the impact controlled probing task has been proposed, considering contact with the plastically deformable object. Approaching velocity conditions to avoid an excess of the allowable penetration depth and control the generated impact force properly are derived from the proposed model. The results of the simulation studies are made for various probing conditions and show the validity of the proposed model.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2004.08a
• /
• pp.29-36
• /
• 2004

The paper describes recent experimental results on the development of Digital Magnetic Compass (DMC), which can provide smart automatic correction functions to the magnetic interferences. The design methodology of magnetic sensing circuit with ring-core fluxgate sensor is represented. The performance results of the sensing circuits are discussed with error analysis by polynomial regressions. As test results, the sensing circuit filtered only the second harmonic signal that is proportional to the direction of earth's magnetic field, and it leads to the obtainment of bearing information. In addition, the total residual errors of DMC can be analyzed by the adoption of polynomial regressions. It shown that the possibility of high precise DMC, in the future.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2003.11a
• /
• pp.169-173
• /
• 2003

We demonstrated the applicability of dry film photoresist (DFR) in photolithography process for fine pitch solder bumping on the polytetrafluoroethylene (PTFE/Teflon) printed circuit board (PCB). The copper lines were formed with $100\;{\mu}m$ width and $18\;{\mu}m$ thickness on the PTFE test board, and varying the gaps between two copper lines in a range of $100-200\;{\mu}m$. The DFRs of $15\;{\mu}m$ thickness were laminated by hot roll laminator, by varying laminating temperature from $100^{\circ}C\;to\;150^{\circ}C$ and laminating speed. We found the optimum process of DFR lamination on PTFE PCB and accomplished the formation of indium solder bumps. The optimum lamination condition was temperature of $150^{\circ}C$ and speed of about 0.63 cm/s. And the smallest size of indium solder bump was diameter of $50\;{\mu}m$ with pitch of $100\;{\mu}m$.