• KCI Concrete Journal
• /
• v.11 no.3
• /
• pp.65-77
• /
• 1999

A portland cement was reinforced by incorporating carbon fiber(CF), silica powder, and impregnating the pores with styrene monomers which were polymerized in situ. The effects of type, length, and volume loading of CF, mixing conditions, curing time and, curing conditions on mechanical behavior as well as freeze-thaw resistance and longer term stability of the carbon-fiber reinforced cement composites (CFRC) were investigated. The composite Paste exhibited a decrease in flow values linearly as the CF volume loadings increased. Tensile, compressive, and flexural strengths all generally increased as the CF loadings in the composite increased. Compressive strength decreased at CF loadings above approx. 3% in CFRC having no impregnated polymers due to the increase in porosity caused by the fibers. However, the polymer impregnation of CFRC improved all the strength values as compared with CFRC having no Polymer impregnation. Tensile stress-strain curves showed that polymer impregnation decreased the fracture energy of CFRC. Polymer impregnation clearly showed improvements in freeze-thaw resistance and drying shrinkage when compared with CFRC having no impregnated polymers.

• Journal of the Korean Wood Science and Technology
• /
• v.32 no.3
• /
• pp.25-32
• /
• 2004

This research work explored physical and mechanical properties of impregnated sawdust boards from three softwood species (P, densifora, L. kaemferi, and P. koraiensis) with phenol-formaldehyde (PF) resin by various vacuum treatment methods of combining pressure, vacuum, and ultrasonic waves. Simultaneous vacuum and ultrasonic wave treatments with no pressure resulted in the greatest increase in resin content, density, dimensional changes (thickness and length), bending strength, and hardness of impregnated board. This result seemed to be attributed to the ultrasonic wave treatment.

• Journal of the Korean Wood Science and Technology
• /
• v.36 no.3
• /
• pp.39-46
• /
• 2008

Repeated impregnation and carbonization processes were performed to prepare high-density woodceramics using a sawdust board. The physical properties were investigated to confirm morphological and structural changes of one-time and two-time phenolic resin-treated and carbonized woodceramics. As comparing between one-time and two-time carbonized woodceramics, the weight and the density of the two-time carbonized woodceramics decreased with an increase of the amount of impregnated phenolic resin. In addition, when the amount of impregnated phenolic resin was about 40% in these woodceramics, the two-time carbonized woodceramics showed higher weight (23.8%) and density (30.0%) than the one-time treatment.

• Journal of Korea Foresty Energy
• /
• v.22 no.1
• /
• pp.24-29
• /
• 2003

Using woodceramics made from sawdust board of Larix leptolepis thinning logs, change in surface temperature were investigated, by the rate of resin impregnation and burning temperature. As the surface temperature of silicon rubber heater was going up, that of woodceramics also increase rapidly. Woodceramics made from under the condition of the rate of resin impregnation 70-80% and burning temperature 800-$1000^{\circ}C$, were higher than that of surface temperature. Also, it was found that woodceramics maintained heat for a long time because the descending velocity of their surface temperature was lower than that of the heater.

• Journal of the Korean Society of Tobacco Science
• /
• v.27 no.2
• /
• pp.178-188
• /
• 2005

To use the filter materials for selective removal of carbonyl compounds in cigarette mainstream smoke, hydrazine such as 2,4-dinitrophenylhydrazine and dansylhydraznie impregnated adsorbents were prepared with perchloric acid or phosphoric acid as a accelerator in hydrazone formation reaction. The change of morphology of adsorbents in various of impregnator were investigated by SEM. Impregnation amount caused by reaction time, acid type and impregnation reagent, and the adsorption properties of carbonyl compounds in cigarette mainstream smoke were investigated. Amounts of impregnation was increased as increasing reaction time. The removal amount for vapor phase carbonyl compounds by 2,4-DNPH impregnated adsorbent was higher than that of dansylhydrazine impregnated adsorbent. The selectivity of 2,4-DNPH impregnated polyacrylic type adsorbent was superior to those of other adsorbents. This results indicated that the 2,4-DNPH impregnated polyacrylic adsorbent was applicable to cigarette filter material because of its fast reactivity and porosity.

• Design & Manufacturing
• /
• v.14 no.4
• /
• pp.11-16
• /
• 2020

In this study, forming of carbon composite parts was performed using an injection/compression molding process. An impregnation of matrix is determined by ability of wet and flow rate between the matrix and reinforcement. The flow rate of matrix passing through the reinforcements is a function of permeability of reinforcement, a viscosity of matrix and pressure gradient on molding, and the viscosity of the matrix depends on the mold temperature, molding pressure and shear strain of matrix. Therefore, compression molding experiment was conducted using a heating mold in order to confirm the possibility of matrix impregnation. The impregnation of the matrix through the porosities between the woven yarns was confirmed by the cross-sectional SEM image of compression molded parts. An injection molding process was also performed at a short cycle time, high molding pressure and low mold temperature than those of compression experiment conditions. Deterioration of impregnation on the surface of molded parts were caused by these injection conditions and it could be the reason of decreasing the maximum tensile strength. In order to improve impregnation of matrix on the surface, injection/compression molding and insert-over molding were applied. As a result of applying injection/compression molding and insert-over molding, it was shown that the improvement of impregnation on the surface and the maximum tensile strength was increased about 2.8 times than the virgin matrix.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.14 no.1
• /
• pp.71-77
• /
• 2010

The concrete structure's durability and integrity is reduced owing to various deterioration phenomena. Therefore, it is important to prevent the deterioration phenomena. This study inquired into the various experimental results of specimens with different dilution concentration and impregnation time by the each solution to present the economic and efficient using method of the inorganic surface penetration agents. As a results, the reasonable dilution concentration and impregnation time of colloidal silica solutions are 15% and 5 minute and for the sodium alumina silicate solutions are 17% and 10 second.

• Journal of the Korean Ceramic Society
• /
• v.46 no.4
• /
• pp.379-384
• /
• 2009

Zirconia is widely used for structural materials in machinery due to its superior properties, such as high strength, high hardness, and high toughness. Zirconia generally has ivory or white color. Therefore many studies are performed for diversification of zirconia color, in order to be widely uitilized for decoration and machine parts which need distincfive color. In this study, graphite is used to prevent structural defect, to maintain superior properties, and to develop black color of zirconia by impregnation method. As specimen was impregnated at $1600^{\circ}C$ for 2 h, bending strength is 1221 MPa, density is $6.01\;g/cm^3$, hardness is 10.1 GPa, absorption coefficient is 0%, transmittance is Fail, chromaticity is 54. The results indicate that black zirconia has enough properties to be adopted as mechanical parts. Optimum impregnation time is 2 h for various observations.

• Journal of the Korean Ceramic Society
• /
• v.30 no.10
• /
• pp.852-858
• /
• 1993

The effect of coal tar ptch-impregnated carbon materials which were made from petroleum coke was investigated at various pressure time and impregnation-sintering cycle. As a result, density and bending strength of the carbon materials were remarkably increased in the condition of pressure times of 5hrs and of the cycle of 3rd times. And the value of d002 and Lc of the graphitic carbon sintered at 230$0^{\circ}C$ shwoed 3.387$\AA$ and 167$\AA$, respectively.

• Journal of the Korean Wood Science and Technology
• /
• v.38 no.1
• /
• pp.43-48
• /
• 2010

This study was aimed at offering basic data to develop a new use of sawdust and rice husk. The results of this study were as follows: In surface temperature of ceramics by resin impregnation rate, the velocity was great in the early time of heat transfer because the temperature precipitously increased to 10 minutes elapsed. Also, the surface temperature of ceramics manufactured in resin impregnation rate of 60~70% indicated the highest. Heat transfer was fast in terms of the changes in surface temperature of ceramics according to the carbonization temperature, as because the density of ceramics made on condition of the carbonization temperature of $1000^{\circ}C$and $1200^{\circ}C$ was high. Moreover, ceramics maintained heat for a long time because the descent velocity of surface temperature of ceramics was slower than that of heater.