• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.4
• /
• pp.332-336
• /
• 2007

In this study, multilayer piezoelectric transformer was manufactured using the PMN-PNN-PZT ceramic and then the electrical characteristics were investigated according to the variations of frequency and load resistance. The voltage step-up ratio of multilayer piezoelectric transformer showed the maximum value at the vicinity of 75 kHz and increased according to the increase of load resistance. When the output impedance coincided with the load resistance, the multilayer piezoelectric transformer showed the temperature rise of less than $20^{\circ}C$ at the output power of 20 W. As the results, the multilayer piezoelectric transformer manufactured at low co-firing temperature of $940^{\circ}C$ using PMN-PNN-PZT ceramics could be stably driven as the step-down transformers.

• Proceedings of the KIEE Conference
• /
• 1995.07a
• /
• pp.95-97
• /
• 1995

A superconducting current generator, or a superconducting rectifier(SCR) is used as a current source to energize a superconducting magnets in SMES, MRI. We selected a full-wave SCR among various SCR models and analyzed its operational characteristics by computer simulation. In process of pumping the current, the improvement of performance is dependent on how much bigger the open resistance of the switch is in comparison to load coil impedance when one of two switches become active. Faster transfer can he seen in resistive commutation mode by shortening the time elapsed for the resistance to arrive at certain level from zero state. Although recovery time for the switch has no direct effect on current pumping, optimal switch design is needed to increasing operational frequency.

• Proceedings of the KIEE Conference
• /
• 2004.11b
• /
• pp.243-245
• /
• 2004

This paper proposes the discrimination method for the fault location, whether it is within the line where the distributed generation(DG) is integrated or out of the line (but sharing the same bus of the substation). In general, DG has to be disconnected from the grid when the fault occurs on the interconnected distribution feeder as soon as possible. However, the faults occured on the neighboring feeder would mistakenly cause the disconnection of the DG. For reliable operation of DG, DG should be sustained at the fault occurred on neighboring distribution feeders. The proposed identification method utilizes the impedance monitored from the DG and examines the coordination of overcurrent relay of the distribution system. This paper describes how the proposed method to identify the faulted feeder and how the method can be utilized.

• Journal of Power System Engineering
• /
• v.2 no.1
• /
• pp.45-51
• /
• 1998

An analyzing method for pressure fluctuations in oil hydraulic pipe network was developed in this study. The object pipe network has multi-branch configuration, and the pipelines of it are composed of metal tubes and flexible hoses. Transfer matrix method, in other words impedance method, was used for the analysis. Values of physical parameters describing the characteristics of flexible hose were measured by experiments and reflected to the analysing procedure. The reliability and usefulness of the analyzing method were confirmed by investigating computed results and experimental results got in this study.

• Journal of electromagnetic engineering and science
• /
• v.19 no.1
• /
• pp.42-47
• /
• 2019

This paper introduces a modified Wilkinson power divider that uses uniform transmission lines for various terminated impedances and an arbitrary power ratio. For the designed power ratio, the proposed divider changes only the electrical lengths of the transmission lines between the input and output ports, and those between the output ports and the isolation resistor. In this case, even when various termination impedances of the ports exist, the divider characteristics are satisfied. To verify the feasibility of the proposed divider, two circuits were designed to operate at a frequency of 2 GHz with 2:1 and 4:1 power splitting ratios and various terminated impedances of 40, 70, and $60{\Omega}$ for one circuit, and 50, 70, and $60{\Omega}$ for the other. The measurement and simulation results were in good agreement.

• Journal of the Korea Society of Computer and Information
• /
• v.24 no.7
• /
• pp.71-78
• /
• 2019

This paper describes a design for a RF receiver to receive satellite digital audio service. The RF receiver designed in this study is a planar structure that is easy to install on the rooftop of a car and is compact in size. In addition, it can be applied to certain commercial models because it has low noise and high gain characteristics. The impedance bandwidth of antenna is 17.8%(415MHz), and the axial ratio is below 3dB as good properties for the bandwidth of 40MHz which is a satellite digital audio service band. Also, it had a broad radiation beamwidth of $95.41^{\circ}$ in H-plane and $117.45^{\circ}$ in E-plane. From the results of the field test of satellite digital audio service reception for the RF receiver, it demonstrated good C/N rate(10.2dB).

• Journal of information and communication convergence engineering
• /
• v.16 no.4
• /
• pp.203-212
• /
• 2018

In this article, a novel design of patch antenna with wide band characteristics is presented. The proposed antenna is having electrical dimensions of $0.14{\lambda}{\times}0.11{\lambda}$ (at lower initial frequency) and footprints of $150mm^2$. Structural parameters optimization shows 3.1-23.5 GHz frequency range for a (reflection coefficient) $S_{11}{\leq}-10dB$ and simulated gain 6.8 dB is obtained. An equivalent circuit model is proposed to get an insight view of antenna. Advanced Systems Design (ADS) simulation results are obtain which confirm the validity of proposed model. Degenerated foster canonical form has been used to explain the reactance and capacitive behavior idea of simulated proposed antenna's input impedance later on an equivalent circuit model and smith chart is also suggested. HFSS and CST have been used to analyze antenna behavior. The proposed antenna can be further used for microwave image detection applications.

• International journal of advanced smart convergence
• /
• v.11 no.4
• /
• pp.41-46
• /
• 2022

This study is a Ku-band array antenna for the manufacture of low-orbit satellite communication terminals, designed to have miniaturization, high gain, and wide beam width. The transmission of low-orbit satellite communication has a right-rotating circularly polarized wave, and the reception has a left-rotating circularly polarized wave. The 4×8 array antenna was separated for transmission and reception, and it was combined with the RF circuit part of the transmitter and receiver, and was terminated in the form of a waveguide for RF signal impedance matching in the form of a transition from the microstrip line to the waveguide. The 30° beam width of the receiver maximum gain of 19 dBi and the 29° beam width of the transmitter maximum gain of 18 dBi are shown. Through this antenna configuration, the system was configured to suit the low-orbit satellite transmission/reception characteristics.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2021.11a
• /
• pp.17-18
• /
• 2021

In the present study, Al-Zn coating was deposited by Arc thermal (AT) and plasma arc thermal (PAT) spray processes, and their corrosion characteristics were studied in 3.5% NaCl through electrochemical impedance spectroscopy (EIS), scanning electron microscope (SEM) and mechanical tests. The bond adhesion result showed that plasma arc sprayed coating had a higher value attributed to compact, dense, and less porous coating compared to arc thermal spray coating which contains defects/pores and uneven morphology as revealed by scanning electron microscope analysis. Electrochemical results revealed that the plasma arc sprayed coating had a high polarization resistance at early stage of immersion, suggesting its excellent corrosion protection performance.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.7 s.98
• /
• pp.768-775
• /
• 2005

In this paper, the broadband cross monopole antenna is presented and the radiation characteristics is investigated f3r various width and height of the radiated element. In the presented antenna, the broadband characteristics is realized by the cross monopole element and the impedance matching section between the element and the ground. To conform the broadband characteristics of the presented antenna, the experimental antenna is designed, fabricated, and its radiation characteristics are measured in $1.75\~2.655$ GHz. It is shown that the designed antenna has the nondirectional pattern in the horizontal plane, the directional pattern in the vertical plane, VSSR less than 1.5, and gain in $2.5\~3.78$ dBi. From these results, the presented antenna is conformed as a broadband indoor antenna which can be used for PCS, WCDMA, Wibro, and satellite DMB band.