• 전자공학회논문지
• /
• 제51권1호
• /
• pp.225-232
• /
• 2014

평판 도파로에서 Cerenkov-idler configuration 형태의 광학적 매개증폭에 대해서 결합모드 이론을 적용하여 결합모드 방정식을 유도하고, 이 방정식의 근사해를 펌핑광의 고갈(depletion)이 없는 경우에 대해서 구한다. 이 근사해로부터 발생되는 idler의 체렌코프 복사각이 $0^{\circ}$도에 접근할 때 signal의 이득이 크게 향상될 수 있음을 보여주고 수치적 예를 보인다.

• 한국군사과학기술학회지
• /
• 제12권5호
• /
• pp.676-682
• /
• 2009

The idler wheel installed at the front side of the newly developed tracked vehicle didn't meet the durability requirement by showing the crack failure near the jointed region at the wheel during the field test. To find the crack developing mechanism we constructed finite element model for the idler wheel representing the behavior of interface between each suspension units, material properties from the material test data and actual loading conditions. This paper shows a result that maximum von Mises stress near the bolt hole on the outer rim is higher than inner idler coressponding to the actual test result and that result was reversed by adopting the reinforcement outside of the outer rim.

• Journal of the Optical Society of Korea
• /
• 제1권1호
• /
• pp.1-4
• /
• 1997

The theoretical limit of the noise correlation between the signal and idler outputs of a nondegenerate optical parametric amplifier (NOPA) with a coherent state signal and vacuum state idler input can be enhanced if a non-vacuum coherent state idler input is employed. By choosing a balanced signal and idler input, the noise correlation is $1/{({\root}g + {\root}{g-1})}^2$, where g is the intensity gain of the NOPA, and that is superior to the prediced outputs with single signal input by approximately 3dB. The result is applicable to all the schemes that use the NOPA to produce a sub-shot noise light generation such as feed-back or feed-forward control.

• 한국자동차공학회논문집
• /
• 제9권1호
• /
• pp.205-215
• /
• 2001

In this study, modeling and analysis procedure for the dynamic analysis of a high mobility tracked vehicle system were studied. The vehicle model used in this investigation is assumed to be consist of two kinematically decoupled subsystems. The chassis subsystem consists of chassis frame, sprocket, support rollers, road wheels, idler wheel, road wheel arms and idle wheel arm, while the track subsystem is represented as a closed kinematic chain consisting of track links and end connectors interconnected by revolute joints with bushing. Nonlinear contact force module describing the interaction between track link, and sprocket, idler wheel, road wheel, support roller, ground was used. The effects of road wheel arms and idler wheel arm due to tension adjuster are also considered.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 춘계학술대회논문집
• /
• pp.199-203
• /
• 2003

Idler of excavator are large product with diameter 500 - 600 mm and parts of a power transmit device. The object of the paper is developed large products by hot closed-die forging. The forging process which is proposed from numerical analysis and various tests is developed a large products with good quality. To estimate the design process parameters such as working load, temperature and flash thickness so on, numerical analysis are used by DEFORM 2D. To obtain a flow stress data and optimal forging temperature is carried out hot compression and tensile test at a various temperature range. Developed product is tested mechanical properties of elongation, hardness and tensile strength so on. Test results are presented excellent mechanical properties.

• 한국자동차공학회논문집
• /
• 제6권4호
• /
• pp.24-31
• /
• 1998

In this study, a procedure is presented for the dynamic analysis of a multibody tracked vehicle system. The planar vehicle model used in this investigation is assumed to consist of two kinematically decoupled subsystems. i.e., the chassis subsystem and track subsystem. The chassis subsystem includes the chassis frame, sprocket, idler and rollers, while the track subsystem is represented as a closed kinematic chain consisting of rigid links interconnected by revolute joints. The nonlinear contact force modules describing the interaction between track links, and sprocket, idler, rollers and ground will be developed.

• Journal of Biosystems Engineering
• /
• 제21권2호
• /
• pp.134-145
• /
• 1996

Since the skid-steer loader is able to work for excavating, lifting and transporting load even at the narrow space, they are widely used in the regular farm and the livestock farm. The skid-steer loader normally adopts the hydrostatic transmission because the power to move the machine backward and forward should be delivered independently on both sides of wheels. Contrast to the mechanical system such as chain and belt transmissions, however, the hydrostatic transmission is less efficient in the use of energy and more difficult in the maintenance. This study was intended to investigate the feasibility of using triangular-type belt clutch and V-belt transmission for the newly developed skid-steer loader in order to overcome the problems stated in the hydrostatic transmission. In the developed triangular-type belt clutch, the centers of driving, driven and idler sheaves are arranged in the triangular shape in a plane, and V-belts were loaded loosely on three sheaves. The power is transmitted by pressing the idler connected to a lever on the loosened V-belt. Contrast to the normal belt clutch using two sheaves, the newly developed belt clutch has the characteristics of small contact-angle of the driving sheave at no bucket load and increasing contact-angle at the time of power transmission. The results of research can be summarized as follows: 1) The developed triangular-type belt clutch adopted a spring-loaded slackside idler which could transmit more power than a fixed idler could by sacrificing the belt life. The life of V-belt used in the power transmission reached at 500 hours(6 months) when the engine power of 11.8 ㎾ was transmitted. Also, it was feasible to develop the large industrial skid-loader with the V-belt transmission by using the proper set of sheaves. 2) The developed skid-steer loader changed the rotating radius and speed with bucket loads as the conventional skid steer loader did. The rotating speed was 47 deg/s at the maximum bucket load of 2.74 kN when the minimum rotating radius was 1.5m. 3) The power required in turning at the bucket load of 2.74 kN was 4 ㎾ and the slippage of V-belt was less than 1%.

• 한국정밀공학회지
• /
• 제28권10호
• /
• pp.1153-1158
• /
• 2011

Roll-to-roll process is an emerging mass production method for printed and flexible electronics such as touch screen panel, RFID tag, thin film solar cell, and flexible display due to its high throughput. High precision in printing and coating is required to apply functional materials onto substrate. For such reason, every part of the roll-to-roll equipment needs to be precisely fabricated and to retain its precision under regular operation. In this article, the precision of cantilever type idler roller and a novel method to mitigate its deflection under web tension loading are discussed and the method is verified using both the numerical and the experimental works. The proposed method improves the structural rigidity of cantilever type roller whose advantages, such as low capital cost and high web path configurability, are maintained.

• Current Optics and Photonics
• /
• 제3권1호
• /
• pp.33-39
• /
• 2019

We report development of a frequency-stabilized mid-infrared continuous-wave (cw) optical parametric oscillator (OPO) based on a fan-out grating MgO:PPLN crystal pumped at 1064 nm. The OPO resonator was designed as a pump-enhanced standing-wave cavity that resonates to the pump and signal beams. To realize stable operation of the OPO, we applied a modified Pound-Drever-Hall technique, which is a well-known method for powerful laser frequency stabilization. Tuning a poling period of the fan-out grating of the crystal allows wavelength-tunable OPO outputs from 1510 nm to 1852 nm and from 2500 nm to 3600 nm for signal and idler beams, respectively. At the idler wavelengths of 2500 nm, 3000 nm and 3500 nm, we achieved more than 50 mW of output powers at a pumping power of 1.1 W. The long-term stability of the OPO was confirmed by recording the power and wavelength variations of the idler for an hour.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.144-147
• /
• 2001

The planar tracked vehicle model used in this investigation consists of two kinematically decoupled subsystem, i.e., the chassis subsystem and the track subsystem. The chassis subsystem include the chassis frame, sprocket, idler and rollers, while the track subsystem is represented as a closed kinematic chain consisting of rigid links interconnected by revolute joints, In this paper, the recursive kinematic and dynamic formulation of the tracked vehicle is used to find the vertical forces and the distances of the certain track moved in the driving direction along the track. These distances and vertical forces obtained are used to calculate the sinkage of a terrain. The FEM is adopted to analyze the interaction between the tracked vehicle and terrain. The terrain is represented by a system of elements with specified constitutive relationships and considered as a piecewise linear elastic, plastic and isotropic material. When the tracked vehicle is moving with different speeds on the terrain, the elastic and plastic deformations and the maximum sinkage for the four different types of a isotropic soil are simulated.