• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.38 no.2
• /
• pp.269-281
• /
• 2018

Unlike its archetype predecessor such as the Highway Capacity Manual of the United States, the Korean Highway Capacity Manual of 2013 provides the analytical models for estimating the saturation flow rates for the lane-occupying work-zones in the proximity of the signalized intersections. Direct application of the revised saturation flow rates into the classic control delay models, however, appears to produce unreasonable delay amount as traffic demand approaches lane-group capacities and surpasses them, which is common phenomena in the work-zones. Complex interaction among vehicles, lane-dropping work-zone geometry and signal operations were never accounted in the traditional control delay models, and considerable differences between the delay model outcomes and field observations are repeatedly experienced. This paper proposes the modified approaches to the delay models in the manual, exerted on all three elements of control delay, and particularly focuses on the temporal and spatial boundary expansion in comparing the simulated results to the estimated ones. Extensive microscopic simulation work and calibration effort supports the modified approaches well enough to use them in the work-zone planning and evaluation.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1999.03a
• /
• pp.249-258
• /
• 1999

Dynamic load and static load tests are performed on steel pipe piles and concrete piles at five construction sites in highway to compare the difference of load bearing mechanisms. At each site, one steel pile is instrumented with electric strain gages and dynamic tests are performed on the pile during installation. Damages of strain gages due to the installation are checked and static test is performed upon the same pile after two or seven days as well. It shows that load transfer from side friction to base resistance behaves somewhat differently according to the results of load-settlement analysis obtained from PDA and static load test. Initial elastic stage of load settlement curves of two load tests is almost similar. But after the yielding point, dynamic resistance of pile behaves more stiffer than static resistance, thus, dynamic load test result might overestimate the real pile capacity compared with static result. Analysis of gage readings shows that unit skin friction increases exponentially with depth. The skin friction is mobilized at the 1∼2m above the pile tip and contributes to the considerable side resistance. Comparison of side and base resistances between the measured value and the calculated value by Meyerhof's bearing capacity equation using SPT N value shows that the calculated base resistance is higher than the measured. Therefore, contribution of side resistance to total capacity shouldn't be ignored or underestimated. Finally, based upon the overall test results, a construction control procedure is suggested.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2006.10a
• /
• pp.574-584
• /
• 2006

Bi-directional loading test data are available to evaluate the design parameters which reflect the characteristics of a construction method and the variations of ground at the site where drilled shafts are installed. The method to obtain the design parameters of a real bridge by hi-directional loading test was introduced. The plans of multi-level testing and installation of measuring instruments should be made according to the rough estimation of axial bearing capacity, the length of pile, and the construction method. While the relationship between end bearing resistance and displacement was obtained directly from the hi-directional loading test, the relationship between unit side resistance and displacement was calculated through the measuring values. 1% displacement of pile diameter was adopted as the criteria of failure for ultimate resistance. As the settlement of pile head at the total ultimate bearing capacity obtained from these method was less than 1.5 % of pile diameter, this method was conservative to use in the field.

• Journal of the Korean Society for Advanced Composite Structures
• /
• v.1 no.1
• /
• pp.34-45
• /
• 2010

This paper describes the design, manufacturing process, testing, application, and assessment of capacity-ratings of the first all advanced composites bridge on a public highway system. In order to verify the bridge design prior to the field application, a sub-scale bridge superstructure was built and tested in the laboratory. The field load test results were compared with those of the finite element analysis for the verification of validity. To investigate its in-service performance, field load testing and visual inspections were conducted under an actual service environment. The paper includes the presentation and discussion for advanced composites bridge capacity rating based on the stress modification coefficients obtained from the test results. The test result indicates that the advanced composites bridge has no structural problems and is structurally performing well in-service as expected. Since these composite materials are new to bridge applications, reliable data is not available for their in-service performance. The results may provide a baseline data for future field advanced composites bridge capacity rating assessments and also serve as part of a long-term performance of advanced composites bridge.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.10a
• /
• pp.481-488
• /
• 1998

Elastomeric bearing is used as one of the most useful way for isolation structures, because the horizontal stiffness is much lower than the vertical stiffness. In the design criteria of Elastomeric bearing, the stability of the bearings is evaluated by shear strain due to compression, lateral displacement, and rotation. The question how soft rubber can sustain heavy structure is now able to be solved by Ultimate capacity test of Laminated Elastomeric Bearings, which results 1,200kg/$\textrm{cm}^2$ of the max. compressive stress and this shows what a sufficient safety factor Elastomeric bearing has !

• Proceedings of the KSR Conference
• /
• 2000.05a
• /
• pp.407-414
• /
• 2000

Recently the geogrids are being used in some large projects such as Inchon International Airport construction, highway construction, and Korean High-Speed Railway construction with not only the merit of simple construction but also reinforcing efficiency for the soft ground. Main function of roadbed is to provide a stable foundation in terms of bearing capacity and settlement for the subballast and ballsat layers. Differential settlement of the railroad should be avoided. The cyclic laboratory model tests were performed to investigate the settlement behavior of geogrid reinforced railroadbed. The ratio of settlement of roadbed under cyclic loading with three layers of geogrid reinforced is less than 1/2 of the roadbed thickness without reinforcement.

• Journal of Korean Society of Transportation
• /
• v.17 no.3
• /
• pp.87-96
• /
• 1999

It is very important to analyze the capacity of basic freeway section in terms of planning, design, and operation of roads. Capacity, in Korean Highway Capacity Manual was Published in 1992, had been determined by data collected in only 4-lane freeway. But, Korea is continuously planning and constructing multi-lane roads for increasing traffic demand. For this reason, it is necessary to determine the capacity for multi-lane freeways. This study goals are two-fold the determination of lane capacity for 8-lane freeway; and the development of methodology determining total capacity using lane friction factor This study utilized the data collected by loop detectors at a station of FTMS in Kyungbu expressway. For determining capacities, this study analyzed maximum flow rate in various aspects such as collecting period, each lane, and total lane in one-way. In addition, this study evaluated the breakdown in traffic flow relations in order to find out interrelation of breakdown among lanes. Through this analysis, this study determined lane friction factors, critical speed, and critical density. Finally, this study expressed a new methodology of capacity analysis for multi-lane freeways using some findings from this analysis.

• Journal of Korean Society of Transportation
• /
• v.23 no.3 s.81
• /
• pp.137-147
• /
• 2005

This study is to define new road capacity concept, and to develop and propose an estimation method, through the analysis of individual vehicular behaviors in continuum flow. Developments in detection technology enable various and precise traffic data collection. The U.S. HCM (Highway Capacity Manual) method does not require such various and precise traffic data, and outputs only limited results. Alternative capacity concepts, which can be classified into a stochastic model and behavioral or deterministic model, are attempts for modeling some prominent traffic flow features, namely so-called a capacity drop and a traffic hysteresis, using such various and precise traffic data. Yet, no capacity concept up-to-date can describe both features. The analysis of individual vehicular behaviors, including speed-density plot per time lap, traffic flow-speed-density diagram per each sampling interval, time headway distribution, and free flow speed distribution, is performed for overcoming the limits of the previous capacity concepts. A stochastic methods are applied to determine time headway for estimating freeway capacity for traffic control.

• Journal of Korean Society of Transportation
• /
• v.12 no.1
• /
• pp.117-132
• /
• 1994

Drivers select approach lane according to various traffic situations as well as their destination. This behavior affects the utilization of lanes and capacity analysis at urban signalized intersections. This paper presents the concept, behavior of lane utilization, and the lane utilization factors which included in the study. Preparation of Korean Highway Capacity Manual (1992). Lane utilization is affected by various traffic and geometric factors which are roadway side friction, median friction, and number of lanes, etc. and it converges to an equal utilization as the degree of saturation (V/C ratio) increase. Lane utilization factor is suggested by the degree of saturation and the number of lanes, and it is presented in this paper.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.05a
• /
• pp.559-564
• /
• 2001

The objective of this experimental research is to assess the seismic performance of circular RC bridge pier specimens retrofitted with fibers which were designed as a prototype of Hagal bridge in the city of Suwon, Korea. Pseudo-dynamic test has been done for two nonseismic test specimens which were nonseismic designed by the related provisions of the Highway Design Specification, and four nonseismic test specimens retrofitted with fibers in the plastic hinge region. Important test parameters were load patterns, and retrofit. The seismic behavior has been analyzed through the displacement ductility, energy analysis, and capacity spectrum. Approximate 7.0 displacement ductility was observed for nonseismic test specimens retrofitted with fibers. It is concluded that these retrofitting test specimens could have sufficient seismic capacity in the region of moderate seismic zone.