• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.864-870
• /
• 2017

The propellants are burned in the pre-burner of the staged combustion cycle engine, and the resulting hot gas drives the turbine, and the turbine operates the turbo pump. The burned gas passing through the turbo pump is supplied to the combustor at high temperature and high pressure, where the gas is supplied in an excess of fuel or an excess of oxidant depending on the amount of fuel or oxidant. When the cycle works at oxidizer-rich staged combustion, its metal pipe can ignite or explode by the impact of even small particles. In this study, we develop the powder combinations for anti-oxidation coating through the analysis of other coating materials and establish the coating process.

• Journal of Environmental Science International
• /
• v.25 no.5
• /
• pp.737-744
• /
• 2016

For electrolysis process using an insoluble electrode, electrochemical performance was greatly affected by the manufacturing method and procedure, such as the firing temperature, pre-treatment, type of precursor solution, coating method, electrode material, etc. Components of the electrode therein is one of the most important factors in electrochemical reaction. To achieve such characteristics, a appropriate ratio of the electrode material should be carefully chosen. The aim of this research was to apply experimental design method in the optimization of electrode component for the maximum generation of oxidants in electrochemical oxidation process. Mixture design, especially expanded simplex lattice design, in DOME (design of mixture experiments) with Design Expert - commercial software - was used to analyze the data. Analysis of variance (ANOVA) showed a high coefficient of determination ($R^2$) value of 0.9470, thus ensuring a satisfactory adjustment of the $3^{rd}$ order special cubic regression model with the experimental data. The application of response surface methodology (RSM) yielded the following regression equation, which is an empirical relationship between the TRO generation concentration and independent variables(mol ratio of 3 electrode components) in a real unit: TRO generation concentration $(mg/L)=TRO\;conc.=98.25{\times}[Ir]+49.71{\times}[Sn]+95.29{\times}[Sb]-16.91{\times}[Ir]{\times}[Sn]-29.47{\times}[Ir]{\times}[Sb]-22.65{\times}[Sn]{\times}[Sb]+703.19{\times}[Ir]{\times}[Sn]{\times}[Sb]$. The optimized formulation of the 3 component electrode for an high TRO (total residual oxidants) generation was acquired at mol ratio of Ir 0.406, Sn 0.210, Sb 0.384 (desirability d value, 1).

• Korean Journal of Materials Research
• /
• v.15 no.1
• /
• pp.31-36
• /
• 2005

It is well known that PCB (Printed Circuit Board) is a complex mixture of various metals mixed with various types of plastics and ceramics. In this study, high temperature pyre-metallurgical process was investigated to extract valuable metallic components from the PCB scrap. For this purpose, PCB scrap was shredded and oxidized to remove plastic materials, and then, quantitative analyses were made. After the oxidation of the PCB scrap, $30.6wt\%SiO_2,\;19.3wt\%Al_2O_3\;and\;14wt{\%}CaO$ were analyzed as major oxides, and thereafter, a typical composition of $32wt\%SiO_2-20wt\%Al_2O_3-38wt{\%}CaO-10wt\%MgO$ was chosen as a basic slag system for the separation of metallic components. Moreover a size effect of crushed PCB scrap was also investigated. During experiments a high frequency induction furnace was used to melt and separate metallic components. As a result, it was found that the size of oxidized PCB scrap was needed to be less 0.9 m to make a homogeneous liquid slag and to recycle metallic components over $95\%$.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.197-197
• /
• 2016

Commercially pure titanium (CP Ti) and Ti-6Al-4V alloys have been widely used for biomedical applications. However, the use of the Ti-6Al-4V alloy in biomaterial is then a subject of controversy because aluminum ions and vanadium oxide have potential detrimental influence on the human body due to vanadium and aluminum. Hence, recent works showed that the synthesis of new Ti-based alloys for implant application involves more biocompatible metallic alloying element, such as, Nb, Hf, Zr and Mo. In particular, Nb and Hf are one of the most effective Ti ${\beta}-stabilizer$ and reducing the elastic modulus. Plasma electrolyte oxidation (PEO) is known as excellent method in the biocompatibility of biomaterial due to quickly coating time and controlled coating condition. The anodized oxide layer and diameter modulation of Ti alloys can be obtained function of improvement of cell adhesion. Manganese(Mn) plays very important roles in essential for normal growth and metabolism of skeletal tissue in vertebrates and can be detected as minor constituents in teeth and bone. Radio frequency(RF) magnetron sputtering in the various PVD methods has high deposition rates, high-purity films, extremely high adhesion of films, and excellent uniform layers for depositing a wide range of materials, including metals, alloys and ceramics like a hydroxyapatite. The aim of this study is to research the Mn coatings on the micro-pore formed Ti-29Nb-xHf alloys by RF-magnetron sputtering for dental applications. Ti-29Nb-xHf (x= 0, 3, 7 and 15wt%, mass fraction) alloys were prepared Ti-29Nb-xHf alloys of containing Hf up from 0 wt% to 15 wt% were melted by using a vacuum furnace. Ti-29Nb-xHf alloys were homogenized for 2 hr at $1050^{\circ}C$. Each alloy was anodized in solution containing typically 0.15 M calcium acetate monohydrate + 0.02 M calcium glycerophosphate at room temperature. A direct current power source was used for the process of anodization. Anodized alloys was prepared using 270V~300V anodization voltage at room. Mn coatings was produced by RF-magnetron sputtering system. RF power of 100W was applied to the target for 1h at room temperature. The microstructure, phase and composition of Mn coated oxide surface of Ti-29Nb-xHf alloys were examined by FE-SEM, EDS, and XRD.

• Clean Technology
• /
• v.23 no.1
• /
• pp.54-63
• /
• 2017

Volatile organic compounds (VOCs) are widely used in both industrial and domestic activities. VOCs are one of the most unpleasant, frequently complaint-rousing factors of pollution around the world. It is now necessary to research and develop an alternative technology that could overcome the problems of the existing odor-control and VOC-eliminating techniques. In this study, essential oil and photocatalytic process was applied in the removal of benzene and toluene, typical VOCs in petrochemistry plant. therefore, this study conducted experiments on the selection of appropriate essential oil, photodegradation, hydroxyl radical generation capacity. The removal efficiency and reaction rate were performed to selecte the type and concentration of essential oil. As a result, removal efficiency of Hinoki Cypress oil was approximately 70% and reaction rate of Hinoki Cypress was high. The results of photolysis experiment, photocatalytic oxidation process showed that the decomposition efficiency of VOCs increased considerably with increasing UV lamp power. In addition, the conversion of VOCs was increased up to $0.1gL^{-1}$ photocatalysts. The hydroxyl radicals measure was performed to determine the ability to generate hydroxyl radicals. The analytical result showed that high $TiO_2$ concentration and lamp power was produced many hydroxyl radical. Experiments of the removal efficiency and reaction rate were performed using essential oil and photooxidation. As a result, the removal efficiency showed that the removal efficiency was increased high temperature and reaction time. The activation energy was calculated from the reaction rate equation at various temperature condition. Activation energy was approximately $18kJmol^{-1}$.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.1
• /
• pp.88-94
• /
• 2012

One of the effective ways to reduce both $NO_x$ and PM at the same time in a diesel CI engine is to operate the engine in low temperature combustion (LTC) regimes. In general, two strategies are used to realize the LTC operation-dilution controlled LTC and late injection LTC - and in this study, the former approach was used. In the dilution controlled regime, LTC is achieved by supplying a large amount of EGR to the cylinder. The significant EGR gas increases the heat capacity of in-cylinder charge mixture while decreasing oxygen concentration of the charge, activating low temperature oxidation reaction and lowering PM and $NO_x$ emissions. However, use of high EGR levels also deteriorates combustion efficiency and engine power output. Therefore, it is widely considered to use increased intake pressure as a way to resolve this issue. In this study, the effects of intake pressure variations on performance and emission characteristics of a single cylinder diesel engine operated in LTC regimes were examined. LTC operation was achieved in less than 8% $O_2$ concentration and thus a simultaneous reduction of both PM and $NO_x$ emission was confirmed. As intake pressure increased, combustion efficiency was improved so that THC and CO emissions were decreased. A shift of the peak Soot location was also observed to lower $O_2$ concentration while $NO_x$ levels were kept nearly zero. In addition, an elevation of intake pressure enhanced engine power output as well as indicated thermal efficiency in LTC regimes. All these results suggested that LTC operation range can be extended and emissions can be further reduced by adjusting intake pressure.

• The Journal of Korean Medicine
• /
• v.37 no.1
• /
• pp.21-33
• /
• 2016

This study aimed to investigate the stability and biological activities of BHSST decoction depending on the preservation temperature and periods. Methods: BHSST decoction was preserved at room temperatures (R/T, $23{\pm}1^{\circ}C$) or refrigeration ($4^{\circ}C$) for 0, 30, 60 and 90 days. To evaluate the stability of BHSST decoction, pH and sugar content were estimated. In addition, high-performance liquid chromatography (HPLC) analysis was performed to determine marker compounds of BHSST decoction. To evaluate anti-inflammatory effect, nitric oxide (NO) and prostaglandin $E_2$ ($PGE_2$) productions were measured in LPS-stimulated RAW 264.7 macrophages. Antioxidant activity was examined using the assays for 3-ethyl-benzothiazoline-6-sulfonic acid (ABTS) and 1-1-diphenyl-2-picrylhydrazyl (DPPH) radical scavenging activities. Results: There was no change in pH and sugar content depending on the preservation temperature and periods of BHSST decoction. Among the major components of BHSST, contents of liquiritin, baicalein and wogonin was reduced time-dependently both at R/T and $4^{\circ}C$. Inhibitory effects of BHSST decoction on NO and PGE2 productions were slightly decreased in a time-dependent manner by 90 days of preservation. In addition, BHSST decoction maintained ABTS and DPPH radical scavenging activities by 60 days while significantly reducing the activities in 90 days of preservation at R/T. By contrast, BHSST decoction had no significant change of ABTS and DPPH radical scavenging activities by 90 days at $4^{\circ}C$. Conclusions: Our results suggest that the stability and efficacy of BHSST decoction are maintained for 60 days at $4^{\circ}C$ rather than R/T.

• Journal of the Korean Magnetics Society
• /
• v.7 no.3
• /
• pp.129-133
• /
• 1997

To investigate the influence of the Hf concentration and the annealing effect in $Co_{1-x}Hf_x$(X=0.16, 0.24 at.%) systems, ferromagnetic resonance experiments have been carried out. Spin wave resonance spectra for all samples consist of several volume modes and one (or two) surface mode. It is suggested that both surfaces of the film have a perpendicular hard axis to the film plane (negative surface anisotropy). The surface anisotropy $K_{s2}$ at substrate-film interface is varied slowly from -0.07 to -0.32 erg/$\textrm{cm}^2$ and the surface anisotropy $K_{s1}$ at film-air interface is varied from 0.18 to -0.47 erg/ $\textrm{cm}^2$ with increasing annealing temperature in the amorphous $Co_{84}Hf_{16}$ thin films. Also, the surface anisotropy $K_{s2}$ is varied slowly from -0.31 to -0.41 erg/$\textrm{cm}^2$ and the surface anisotropy $K_{s1}$is varied from -0.19 to -0.60 erg/$\textrm{cm}^2$ with increasing annealing temperature in the amporphous $Co_{84}Hf_{16}$ thin films. We conjecture that the variation of surface anisotropy $K_{s1}$ is due to the increase of Co concentration resulted from Hf oxidation for low temperature annealing(150~175 $^{\circ}C$) and the diffusion of Co atoms near the film surfaces for high temperature annealing (200~225 $^{\circ}C$).

• Journal of Soil and Groundwater Environment
• /
• v.17 no.3
• /
• pp.76-85
• /
• 2012

Geochemical and ecological properties of remediated soil and gas exhausted from a low-temperature thermal desorption (LTTD) process were analyzed to assess the environmental impact of LTTD treatment. Soil characteristics were examined with regard to the chemical (EC, CEC, and organic matter) and the ecological (dehydrogenase activity, germination rate of Brassica juncea, and growth of Eisenia andrei) properties. The exhaust gases were analyzed based on the Air Quality Act in Korea as well as volatile organic compounds (VOCs) and mixed odor. Level of organic Organic matter of the soil treated by LTTD process was slightly decreased compared to that of the original soil because the heating temperature ($200^{\circ}C$) and retention time (less than 15 minutes) were neither high nor long enough for the oxidation of organic matter. The LTTD process results in reducing TPH of the contaminated soil from $5,133{\pm}508$ mg/kg to $272{\pm}107$ mg/kg while preserving soil properties. Analysis results of the exhaust gases from the LTTD process satisfied discharge standard of Air Quality Law in Korea. Concentration of VOCs including acetaldehyde, propionaldehyde, butyraldehyde and valeraldehyde in circulation gas volatilized from contaminated soil were effectively reduced in the regenerative thermal oxidizer and all satisfied the legal standards. Showing ecologically improved properties of contaminated soil after LTTD process and environmentally tolerable impact of the exhaust gas, LTTD treatment of TPH-contaminated soil is an environmentally acceptable technology.

• Journal of the Korean Magnetics Society
• /
• v.7 no.1
• /
• pp.38-43
• /
• 1997

For amorphous $Co_{1-x}Ti_x$(X=0.13, 0.16, 0.21 at.%) thin films deposited by DC magnetron sputtering method ferromagnetic resonance experiments have been used to investigate the dependence of surface magnetic properties according to annealing temperature (150~225 $^{\circ}C$). Spin wave resonance spectra for all annealing temperatures consist of several volume modes and one(or two) surface mode. It is suggested that both surfaces of the film have a perpendicular hard axis to the film plane(negative surface anisotropy). Also, the surface anisotropy $K_{s2}$ at substrate film interface is varied slowly from -0.11 to -0.25 erg/ $\textrm{cm}^2$ and the surface anisotropy $K_{s1}$ at film-air interface is varied from 0.16 to -0.53 erg/ $\textrm{cm}^2$ with increasing annealing temperature. We conjecture that the variation of surface anisotropy $K_{s1}$ is due to the increase of Co concentration resulted from Ti oxidation for low temperature annealing(150~200 $^{\circ}C$) and the diffusion of Co atoms near the film surfaces for high temperature annealing(225~250 $^{\circ}C$).