• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.8 no.4
• /
• pp.261-267
• /
• 2010

The pyrometallurgical nuclear fuel recycle process, called pyroprocessing, has been known as a promising nuclear fuel recycling technology. Pyroprocessing technology is crucial to advanced nuclear systems due to increased nuclear proliferation resistance and economic efficiency. The basic concept of pyroprocessing is group actinide recovery, which enhances the nuclear proliferation resistance significantly. One of the key steps in pyroprocessing is "electrowinning" which recovers group actinides with lanthanide from the spent nuclear fuels. In this study, a vertical cadmium distiller was manufactured. The evaporation rate of pure cadmium in vertical cadmium distiller varied from 12.3 to $40.8g/cm^2/h$ within a temperature range of 773 923 K and pressure below 0.01 torr. Uranium - cadmium alloy was fabricated by electrolysis using liquid cadmium cathode in a high purity argon atmosphere glove box. The distillation behavior of pure cadmium and cadmium in uranium - cadmium alloy was investigated. The distillation behavior of cadmium from this study could be used to develop an actinide recovery process from a liquid cadmium cathode in a cadmium distiller.

• Korean Chemical Engineering Research
• /
• v.52 no.4
• /
• pp.522-529
• /
• 2014

Circulating fluidized bed system consists of SEWGS reactor - lower loop seal - regeneration reactor - riser - cyclone - upper loop seal has been used for solid circulation between the SEWGS reactor and the regeneration reactor in a SEWGS system for pre-combustion $CO_2$ capture. A vertical type lower loop seal has been used in current system but this lower loop seal requires high gas flow rate through the lower loop seal for fluidization and smooth solid circulation, and consequently, causes slugging behavior sometimes. To overcome these disadvantages, inclined type lower loop seal was proposed by this study. Solid circulation characteristics with change of lower loop seal geometry were measured and compared in a bubbling - bubbling - riser type circulating fluidized bed using $CO_2$ absorbent (P-78) as bed material at ambient temperature and pressure. We could conclude that the inclined lower loop seal is better than the vertical type lower loop seal from the viewpoints of minimum flow rate requirement for stable solid circulation and solid height change during solid circulation.

• Food Science and Preservation
• /
• v.16 no.3
• /
• pp.355-361
• /
• 2009

In this study, raw ginseng produced by different methods was puffed, and physicochemical properties were analyzed and compared. Raw ginseng included white ginseng lateral root (WGL), red ginseng lateral root (RGL), red ginseng main root (RGM), and red ginseng main root with 15% (w/w) moisture (RGMM). All samples were puffed at a pressure of 7 kg/cm2. Crude saponin content was increased after puffing compared with that of control ginseng. RGM and RGMM showed significant increases in crude saponin content, from 1.67% and 1.41% to 2.84% and 3.09% (all w/w), respectively. However, the ginsenoside content of WGL was decreased after puffing. Rg3, Rh1, and Rh2 values of red ginseng were increased by puffing compared with those of control red ginseng. The total sugar content of ginseng decreased after puffing. The mineral components of puffed ginseng were similar to those of raw ginseng. Levels of total phenolic compounds and antioxidant activities of ginseng were increased after puffing, and electron-donating ability was greatly increased. The acidic polysaccharide content of ginseng increased slightly and the amino acid content decreased due to the high temperature used during puffing.

• Journal of the Korean Magnetics Society
• /
• v.13 no.2
• /
• pp.64-69
• /
• 2003

Ba-ferrite thin films were prepared on Si substrate with ${\alpha}$-Fe$_2$O$_3$ underlayer by a pulsed laser deposition system and characterized by X-ray, SEM, Mossbauer spectroscopy and VSM. The appropriate conditions of pulsation in ${\alpha}$-Fe$_2$O$_3$ and Ba-ferrite were the oxygen pressure of 0.1 Torr at a substrate temperature of 400$^{\circ}C$. Ba-ferrite crystals had the forms of ellipsoidal or needle and the grains shaped the more lumps with increasing the film thickness. Mossbauer spectroscopy assured that the direction of atomic spin in Fe ion was not random but had the tendency of arrangement normal to the substrate. The coercive force and squareness of hysteresis were larger in normal than in plane to the substrate but, the magnetic saturation moment was contrary to them. The spin arrangement was strongly affected by ${\alpha}$-Fe$_2$O$_3$ underlayer and the high coercive force and squareness were influenced by this. The crystal structure was conformed to be a Magntoplumbite symmetry with the hexagonal unit cell and the lattice constant of a increased with increasing film thickness, while c decreased

• Journal of the Korean Institute of Intelligent Systems
• /
• v.26 no.3
• /
• pp.246-252
• /
• 2016

Since thermal power plant (TPP) equipment is operated under very high pressure and temperature, failures of the equipment give rise to severe losses of life and property. To prevent the losses, fault detection method is, therefore, absolutely necessary to identify abnormal operating conditions of the equipment in advance. In this paper, we present Mahalanobis distance (MD) based fault detection method for steam boiler tube in TPP. In the MD-based method, it is supposed that abnormal data samples are far away from normal samples. Using multivariate samples collected from normal target system, mean vector and covariance matrix are calculated and threshold value of MD is decided. In a test phase, after calculating the MDs between the mean vector and test samples, alarm signals occur if the MDs exceed the predefined threshold. To demonstrate the performance, a failure case due to boiler tube leakage in 200MW TPP is employed. The experimental results show that the presented method can perform early detection of boiler tube leakage successfully.

• Journal of the Korean Ceramic Society
• /
• v.41 no.5
• /
• pp.370-374
• /
• 2004

Sr$_{l-x}$Ba$_{x}$Al$_2$O$_4$:Eu (x = 0, 0.1, 0.2, and 0.3 mol) phosphor was synthesized by the hydrothermal method and its properties of photoluminescence and long-afterglow were investigated. The mixtures of Sr(NO$_3$)$_2$, Al(NO$_3$)$_3$9$H_2O$, and Eu(NO$_3$)$_3$$.$6$H_2O$ salts dissolved in distilled water, after controlling their pH by NH$_4$OH solution, put into an Autoclave reactor with high temperature and pressure to react. Such synthesized SrAl$_2$O$_4$:Eu powders showed homogeneous and ultra-fine particles of sub-micron size. In order to have the photoluminescence characteristic, powders were heat treated at 1100 -140$0^{\circ}C$ for 2 h in Ar/H$_2$ reduction atmosphere. Photoluminescence spectra showed a excitation along the wide wavelength of 250 ∼ 450 nm, and broaden emission with maxima peak at 520 nm. Also, it showed a good long afterglow with decaying over 1000 sec after excitation illumination for 10 min. In addition, the microstructure and crystal structure of SrAl$_2$O$_4$:Eu powders were investigated by an SEM and XRD, respectively.

• Journal of Radiation Protection and Research
• /
• v.21 no.1
• /
• pp.1-7
• /
• 1996

In this paper, we discussed the fabrication and characterization of bulk type CdZnTe detector for pocket surveymeter. The resistivity of CdZnTe single crystal grown by the High Pressure Bridgman method is in the mid of $10^9$ ohm-cm. The detector structure is Au/CdZnTe/Au and gold electrode is formed by electroless deposition method. Resolutions of 4.8keV and 2.2keV were observed at 22.2keV line of $^{109}Cd$ and 59.6keV line of $^{241}Am$ at room temperature, respectively. We also constructed the small size pocket surveymeter using home made CdZnTe detector. It shows the good linearity over a range from 1mR/hr to 10R/hr with deviation less than 5%. The sensitivity of the surveymeter developed is $2.2{\times}10^3 cps/Rad\;hr^{-1}$ for the 662keV of $^{l37}Cs\;{\gamma}-ray$.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.5
• /
• pp.437-447
• /
• 2016

In a nuclear power plant, the fuel assembly, which is composed of fuel rods, burns, and the high temperature can generate power. The fuel rod consists of pellets and a cladding that covers the pellets. It is important to understand the pellet-cladding mechanical interaction with regard to nuclear safety. This paper proposes simulation of the PCMI. The gap between the pellets and the cladding, and the contact pressure are very important for conducting thermal analysis. Since the gap conductance is not known, it has to be determined by a suitable method. This paper suggests a solution. In this study, finite element (FE) contact analysis is conducted considering thermal expansion of the pellets. As the contact causes plastic deformation, this aspect is considered in the analysis. A 3D FE module is developed to analyze the PCMI using FORTRAN 90. The plastic deformation due to the contact between the pellets and the cladding is the major physical phenomenon. The simple analytical solution of a cylinder is proposed and compared with the fuel rod performance code results.

• Korean Journal of Food Science and Technology
• /
• v.25 no.6
• /
• pp.637-642
• /
• 1993

Changes in the physicochemical characteristics and triglyceride molecular species of corn oil under the following condition of hydrogenation; temperature $180^{\circ}C,\;H_{2}$, pressure $2.0{\pm}0.3bar$, the amount of Ni catalyst 0.048%(Ni/oil by wt.) and agitation speed 300 rpm. The rate of hydrogenation, expressed as the reduction rate of the iodine value with respect to time, is first order and high (K>0.01). When the reduction rate of the iodine value was 39.9%, hydrogenation time was 30 min, 18:1 was highest(77.06%), thereafter that was decreased and 18:0 increased. In the triglyceride composition, OLL, LLL were reduced markedly in 10 min, thereafter reduced slightly. And PLO, PLL, OLO were eliminated in first 30 min. On the other hand, POO, PLS(CN52) and OOO, SLO(CN54) were increased sharply, and then that showed little change. The melting point(MP) of hydrogenated corn oil were $27.8^{\circ}C\;and\;44.1^{\circ}C$ after 20 min and 60 min, respectively. Trans isomer content increased to 46.8% during 40 mins of hydrogenation and then decreased insignificantly. The solid fat content were linearly increased with hydrogenation time. Accordingly, it is confirmed that this condition of hydrogenation was selective, preferential elimination of polyunsaturated fatty acid went stepwise and trans isomer was formed promotedly. These results suggest that fat modification techniques can be used for practical application.

• Korean Journal of Food Science and Technology
• /
• v.31 no.5
• /
• pp.1268-1274
• /
• 1999

Pine twigs with buds were cut into $2{\sim}3\;mm$ long pieces and about 18g was used for each experiment. Pressure and temperature ranges employed were $100{\sim}300\;bar$ and $35{\sim}55^{\circ}C$, respectively. Volatile compounds of extracts were isolated and identified by gas chromatography and mass selective detector. Twenty three compounds from the extracts were identified. Limonene and ${\beta}-pinene$ were found to be the major components with $32.6{\sim}43.4%$ being limonene. Extracts obtained by supercritical fluid extraction were lower in monoterpene and higher in oxygenated terpenoids than those by steam distillation and solvent extraction (SDE). Sensory evaluation showed that the pine flavor extracted using supercritical carbon dioxide was much better in quality than that of SDE. In conclusion, it was found out that supercritical fluid extraction can successfully be applied to extract high quality flavor from pine.