• Steel and Composite Structures
• /
• v.23 no.2
• /
• pp.205-215
• /
• 2017

The use of advanced fibre composite materials in bridge engineering offers alternative solutions to structural problems compared to traditional construction materials. Advanced composite or fibre reinforced polymer (FRP) materials have high strength to weight ratios, which can be especially beneficial where dead load or material handling considerations govern a design. However, the reduced weight and stiffness of FRP footbridges results in generally poorer dynamic performance, and vibration serviceability is likely to govern their design to avoid the footbridge being "too lively". This study investigates the dynamic behaviour of the 51.3 m span Wilcott FRP suspension footbridge. The assessment is performed through a combination of field testing and finite element analysis, and the measured performance of the bridge is being used to calibrate the model through an updating procedure. The resulting updated model allowed detailed interpretation of the results. It showed that non-structural members such as the parapets can influence the dynamic behaviour of slender, lightweight footbridges, and consequently their contribution must be included during the dynamic assessment of a structure. The test data showed that the FRP footbridge is prone to pedestrian induced vibrations, although the measured response levels were lower than limits specified in relevant standards.

• Proceedings of the KSME Conference
• /
• 2000.11a
• /
• pp.516-521
• /
• 2000

Most of studies, using ESPI method, have handled tension, thermal and vibration analysis, and is limited to isotropic materials. However, tension and vibration simultaneously are loaded in real structure. Also, almost study using ESPI method is locally limited to the analysis on the isotropic materials and a few studies on the anisotropic materials have reported. Existing methods, such as the accelerometer method and FEA method, to analyze vibration have some disadvantages. Using the accelerometer method that is generally used to analyze vibration phenomena, it is impossible to analyze vibration on the oscillating body and one can observe no vibration mode shape during experiment. In case of the FEA method, it is difficult to define boundary conditions correctly if the shape of a body tested is complex, and one can just obtain vibration mode shapes on the peak amplitude in each modes. In this study, plane plate of stainless steel(STS304), isotropic material, that is used as structural steel is analyzed about vibration characteristics under tension. Also, in the study of stainless steel, the characteristics of composite material(AS4/PEEK) used as high strength structural material in aircraft is evaluated about vibration under tension, and studies the effect of tension on vibration.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.45 no.4
• /
• pp.27-33
• /
• 2013

Manufacturing fabrics from dissolving cellulosic pulp is increasing in these days. For making high quality of cellulose-based fabrics, control of cellulose DP (degree of polymerization), its alpha cellulose content, its brightness, and its crystallinity are important. To process the cellulosic raw material, refining of cellulosic fibers is essential, and it is important to know if refining affects those important cellulose properties. The effects of PFI mill and Valley beater refining on the alpha-cellulose content, cellulose DP, crystallinity, and paper mechanical properties of wood and two different cotton fibers were studied. The results showed that PFI mill refining rarely affected those properties. Fibers refined by a Valley beater displayed a small reduction in fiber length in comparison with those refined by a PFI mill. However, the Valley beater refining method produced almost no changes in cellulose properties, either. The refining process seemed to have very little effect on the cellulose DP, crystallinity index, or alpha-cellulose content until the freeness decreased to around 300 mL CSF for wood and 100 mL CSF for cotton fibers, respectively. There were also no differences in tensile strength development in two refining methods.

• Transactions of Materials Processing
• /
• v.18 no.6
• /
• pp.453-457
• /
• 2009

In this paper, plastic deformation behaviors of ESW105 and SCM435 steels are revealed by simulations and experiments. ESW105 is the special pre-heat-treated steel characterized by high initial yield strength and negligible strain-hardening behavior. The flow stresses of the two steels for large stain are calculated from tensile tests. Axial and lateral compressions of cylindrical bars are tested and simulated and the deformed shapes are compared to characterize the plastic deformation behaviors of the two materials. A forward extrusion process of a cylindrical bar is also simulated to reveal the difference. It has been shown that there are pretty much difference in plastic flow between ESW105 and SCM435 which causes from the difference in strain-hardening capability, implying that the experience-oriented design rules for common commercial materials may lead to failure in process design when the new material of ESW105 is applied without consideration of its plastic deformation behavior.

• Journal of Welding and Joining
• /
• v.30 no.5
• /
• pp.40-45
• /
• 2012

Nowadays in Republic of Korea, whole amount of the thermite welding powder for rail joinning is dependent on import. However the demand of the thermite welding powder would be enlarge because some constructing high-speed train and city metro projects are currently in progress. In addition this is the main reason why we should develop the thermite welding powder, domestically. This study is focused on utilizing the recyclable materials like Al powders from cans and iron oxide scales from wire rods as the main components of the thermite welding powder. By minimizing Al content in weld zone by controlling the mixing ratio of the Al powder in the thermite welding powder, the excessive dissolution of the Si and Mn components came from the Al powders could be controled. The tensile strength of welding zone in welded rail was 740 MPa, with that the developed thermite welding powder.

• Journal of the Korean Society for Heat Treatment
• /
• v.14 no.4
• /
• pp.212-219
• /
• 2001

The fatigue test was carried out to evaluate the fatigue characteristics of fire resistance steel for frame structure and heat affected zone (HAZ) by the one side Gas Metal Arc Welding (GMAW). In this paper, the fatigue crack growth behavior was investigated with the compact tension specimen of base metal and the HAZ according to chemical composition and rolling end temperature, respectively. And the acoustic emission signals obtained from the fatigue test were analyzed by the time-frequency analysis method as a nondestructive evaluation. Main results obtained are summarized as follows; The hardness was appeared softening phenomenon that weld metal and HAZ are lower than that of base metal. Fatigue life of welded specimen was longer than that of base metal. m was 3~4.5 in base metal and 3.8~5.8 in HAZ. The main frequency range of acoustic emission signal analyzed from time-frequency method is different with the range by noise and crack. Also, it could be classified that it was also generated by fracture mechanics of dimple, inclusion etc.

• Applied Chemistry for Engineering
• /
• v.7 no.3
• /
• pp.536-542
• /
• 1996

Water-based acrylic sizing agent(GSW-7000) was prepared by emulsion copolymerization for sizing polyester yarns. Ammonium salt version of the acrylic sizing agent offered greater abrasion resistance to weaving forces and water resistance for water jet loom. GSW-7000 exhibited proper viscosity for sizing, high penetration ability and excellent adhesion to polyester yarn. It was possible to reduce the size pick-up to 70~80% of ordinary solvent-based sizing agent due to excellent adhesive strength of GSW-7000.

• Journal of the Korean Ceramic Society
• /
• v.42 no.12 s.283
• /
• pp.816-820
• /
• 2005

The doped-ceria is a strong candidate material for an intermediate temperature SOFC. However, the mechanical strength and the magnitude of electrical conductivity need to be increased at low sintering temperature. In this study, to improve both properties, $1at\% $ of Mg, Ca, Cr, Fe, Co, Ni, Cu, Ga, and Zr were added to the GDC20 ($20at\%$ Gd-doped Ceria) and sintered at $1350^{\circ}C$ that is $250^{\circ}C$ lower than $1600^{\circ}C$. With addition, the relative density of the sintered sample increased. Fe, Co, Ni, Cu, Ga doped-GDC20 showed high relative density over $92\%$. Among them, Ga doped-GDC20 showed the most improved sinterability. The conductivity of doped­GDC20 increased by $\~10$ times at $300\~700^{\circ}C$.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.17 no.1
• /
• pp.16-22
• /
• 2018

Silicon carbide (SiC) is used in various semiconductor processes because it has superior thermal, mechanical, and electrical characteristics as well as higher chemical and corrosion resistance than existing materials. Due to these characteristics, various manufacturing technologies have been developed for SiC. A recent development among these technologies is Chemical Vapor Deposition SiC (CVD-SiC). Many studies have been carried out on the processing and manufacturing of CVD-SiC due to its different material characteristics compared to existing materials like RB-SiC or Sintered-SiC. CVD-SiC is physically stable and has excellent chemical and corrosion resistance. However, there is a problem with increasing the thickness, because it is manufactured through a deposition process. Additionally, due to its high strength and hardness, it is difficult to subject to machining.

• Corrosion Science and Technology
• /
• v.10 no.4
• /
• pp.143-150
• /
• 2011

Copper electroplating has been applied to various fields such as decorative plating and through-hole plating. Technical realization of high strength copper preplating for wear-resistant tools and molds in addition to these applications is the aim of this work. Brighters and levelers, such as MPSA, Gelatin, Thiourea, PEG and JGB, were added in copper sulfate electrolyte, and the effects of these organic additives on the hardness were evaluated. All additives in this work were effective in increasing the hardness of copper electrodeposits. Thiourea increased the hardness up to 350 VHN, and was the most effective accelarator in sulfate electrolyte. It was shown from the X-ray diffraction analysis that preferred orientation changed from (200) to (111) with increasing concentration of organic additives. Crystallite size decreased with increasing concentration of additive. Hardness was increased with decreasing crystallite size, and this result is consistent with Hall-Petch relationship, and it was apparent that the hardening of copper electrodeposits results from the grain refining effect.