• 수산해양기술연구
• /
• 제19권1호
• /
• pp.17-24
• /
• 1983

흑, 적, 녹색의 그물무늬의 시각막을 15.0, 37.4, 62.9cm/sec의 속도로 회전시켰을 때의 송사리 Orizias latipes의 방어 Seriola quinqueradiata의 시각운동반응을 조사한 결과는 다음과 같다. 1. 시각운동반응율은 송사리가 95%, 방어가 94%였다. 2. 송사리가 잘 반응하는 시각막의 색상은 흑, 적, 녹색의 순이며, 흑색에 대한 적, 녹색의 차이는 뚜렷했으나 적색과 녹색의 차이는 뚜렷하지 않았다. 3. 방어가 잘 반응하는 시각막의 색상은 흑, 적, 녹색의 순이며, 색상에 따른 차이는 뚜렷하지 않았다. 4. 시어가 잘 반응하는 시각막의 속도는 62.9, 37.4, 15.0cm/sec의 순이며, 속도에 따른 차이는 뚜렷했다

• 대한방사선기술학회지:방사선기술과학
• /
• 제13권2호
• /
• pp.21-25
• /
• 1990

This report is study about difference of H-D curve in regular film and ortho type film, and obtained results as follows : 1. In the blue-color emission intensifying screen, ortho type films and in the green-color emission intensifying screens, regular type are decreased in their gradient. 2. When joint use of regular type film and ortho type film, the gradient difference not seen in blue color screen. 3. The gradient difference seen clearly in G4, KM screens(green color emission intensifying). Especially, in part of high film density, the gradient difference are great. So we have to right use of screen and film because not matched used of theare the sensitivity and gradient are decrease.

• Journal of Information Display
• /
• 제4권3호
• /
• pp.6-11
• /
• 2003

We have fabricated a carbon nanotube field emission display (CNT-FED) panel with a 2-inch diagonal size by using a screen printing method and vacuum in-line sealing technology. The sealing temperature of the panel was around 390$^{\circ}C$ and the vacuum level was obtained with 1.4x$10^{-5}$torr at the sealing. When the field emission properties of a fabricated and sealed CNT-FED panel were characterized and compared with those of the unsealed panel which was located in a test chamber of vacuum level similar with the sealed panel. As a result, the sealed panel showed similar I-V characteristics with unsealed one and uniform light emission with very high brightness at a current density of 243 ${\mu}A/cm^2$, obtained at the electric field of 10 V/${\mu}m$.

• 한국전기전자재료학회논문지
• /
• 제26권3호
• /
• pp.246-251
• /
• 2013

Screen printing is commonly used to form the front/back electrodes in silicon solar cell. But it has caused high resistance and low aspect ratio, resulting in decreased conversion efficiency in solar cell. Recently the plating method has been combined with screen-printed c-Si solar cell to reduce the resistance and improve the aspect ratio. In this paper, we investigated the effect of light induced silver plating with screen-printed c-Si solar cells and compared their electrical properties. All wafers were textured, doped, and coated with anti-reflection layer. The metallization process was carried out with screen-printing, followed by co-fired. Then we performed light induced Ag plating by changing the plating time in the range of 20 sec~5min with/without external light. For comparison, we measured the light I-V characteristics and electrode width by optical microscope. During plating, silver ions fill the porous structure established in rapid silver particle sintering during co-firing step, which results in resistance decrease and efficiency improvement. The plating rate was increased in presence of light lamp, resulting in widening the electrode with and reducing the short-circuit current by shadowing loss. With the optimized plating condition, the conversion efficiency of solar cells was increased by 0.4% due to decreased series resistance. Finally we obtained the short-circuit current of 8.66 A, open-circuit voltage of 0.632 V, fill factor of 78.2%, and efficiency of 17.8% on a silicon solar cell.

• 설비공학논문집
• /
• 제16권1호
• /
• pp.70-76
• /
• 2004

High-temperature cylindrical sodium/stainless-steel heat pipes were manufactured and tested for transient as well as steady states. Total length of the heat pipe was 1 m and the diameter was 25.4 mm. Screen meshes of 3 different sizes were used to estimate the effect of mesh size on the thermal performance of the heat pipe. The minimum thermal resistance achieved was as low as 0.02$^{\circ}C$/W for the maximum thormal load of 2 ㎾. The average heat transfer coefficient in the evaporator was about 2,000 ㎾/$m^2$K and those in the condenser region were up to 5 times higher.

• 대한방사선기술학회지:방사선기술과학
• /
• 제11권2호
• /
• pp.21-26
• /
• 1988

Newly developed orthochromatic film HR series have many different types according to high speed, high resolution and special latitude. And now authors have practiced various screen-film combinations, those were usual regular type Fuji new RX film-LT screen and orthochromatic type HR films-rare earth G3, G4 screens. As a result of the experiment, we obtained high speed with high resolution and expansion of diagnostic range on the following combinations compared with usual new RX/LT series. Those combinations were RXO-G and HR-L films to skull, HR-G films to knee joint and hand part, HR-L film to abdomen. Therefore it may be desirable to select adquate kinds of HR series films according to investigated parts.

• Journal of Biosystems Engineering
• /
• 제30권4호
• /
• pp.195-201
• /
• 2005

The output of Stirling engine is influenced by the regenerator effectiveness. The regenerator effectiveness is influenced by heat transfer and flow friction loss of the regenerator matrix. In this paper, in order to provide a basic data for the design of regenerator matrix, characteristics of heat transfer and flow friction loss were investigated by a packed method of matrix in the oscillating flow as the same condition of operation in a Stirling engine. As matrices, several kinds of combined wire screen meshes were used. The results are summarized as follows; The packed meshes with high mesh no. in the side of heater part of regenerator showed effective than the packed meshes with low mesh no. in the side of cooler part of regenerator. The temperature difference and pressure drop of the regenerator were not made by the specific surface area of wire screen meshes but by the minimum free-flow area to the total frontal area. Among the No. 150 single screen meshes, 200-60 combined meshes, the 200-150-100 combined meshes showed the highest in effectiveness.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제41회 하계 정기 학술대회 초록집
• /
• pp.125-125
• /
• 2011

In this study, we investigated the electrical, optical, structural, and surface properties of indium zinc oxide (IZO)/Ag/IZO multilayer electrode grown by specially designed roll-to-roll sputtering system using the flexible substrate. By the continuous roll-to-roll sputtering of the bottom IZO, Ag, and top IZO layers at room temperature, they were able to fabricate a high quality IZO/Ag/IZO multilayer electrode. At optimized conditions, the bottom IZO layer (40 nm) was deposited on a flexible substrate. After deposition of the Bottom IZO layer, Ag layer was deposited onto the bottom IZO film as a function of DC power (200~500 W). Subsequently, the top IZO layer was deposited onto the Ag layer at identical deposition conditions to the bottom IZO layer (40 nm). We investigated the characteristics of IZO/Ag/IZO multilayer electrode as a function of Ag thickness. It was found that the electrical and optical properties of IZO/Ag/IZO multilayer electrode was mainly affected thickness of the Ag layer at optimized condition. In case of IZO/Ag/IZO multilayer electrode with the Ag power (350W), it exhibited a low sheet resistance of 7.1 ohm/square and a high transparency of 86.4%. Furthermore, we fabricated the touch screen panel using the IZO/Ag/IZO multilayer electrode, which demonstrate the possibility of the IZO/Ag/IZO multilayer electrode grown by roll-to-roll sputtering system as a transparent conducting layer in the touch screen panel.

• 펄프종이기술
• /
• 제47권4호
• /
• pp.66-75
• /
• 2015

Disposable diaper waste is consisted of plastic, fiber, and SAP (Super Absorbent Polymer). They are valuable to be used as raw materials of other products including plastic blocks and pulp mold. Nevertheless, disposable diaper waste have been disposed by landfill and incineration without recycling. Due to strict environmental regulations it is necessary to develop fractionation technique to recycle the disposable diaper waste. In this study the fractionation technique using pilot-scale stock preparation units was investigated. Process for separation of plastic and fibers from disposable diaper waste was composed by the combination of pilot-scale pulper, drum screen, screen and cleaner. Recovery rate of plastics and fiber was checked according to the various operating conditions. In drum screen, recovery rate of plastic was high when the cut size of disposable diaper waste was $5cm{\times}5cm$. The highest recovery rate of fiber was achieved with 0.3 mm slot screen. It is important to control the neutral state of SAP for improvement of recovery rate of fiber since SAP can be swelled easily in water. Therefore SAP can be controlled efficiently by the addition of calcium chloride into the pulper. Consequently recovery rates of plastics and fibers were over 90 and 80% under the optimum pilot operating conditions.

• 마이크로전자및패키징학회지
• /
• 제22권4호
• /
• pp.83-89
• /
• 2015

본 논문에서는 졸-침투와 직접-패턴 공정을 이용하여 향상된 압전 후막의 전기적 특성과 우수한 패터닝 특성을 동시에 만족할 수 있는 제작 방법을 제시한다. 저온(< $850^{\circ}C$) 공정 후 후막의 고밀도 및 직접-패턴의 목적을 달성하기 위해서, 감광성 티탄산 지르콘산 연 ($Pb(Zr,Ti)O_3$, PZT) 졸을 스크린인쇄된 PZT 후막 내부로 침투시켰다. 직접-패턴된 PZT막은 포토크롬마스크와 UV 조사에 의해서 일정한 간격으로 인쇄된 후막 위에 성공적으로 형성되었다. 스크린인쇄된 후막은 분말형태의 기공성 구조를 갖고 있어 조사된 UV빛이 산란되기 때문에, 감광성 졸-침투 공정을 할 때 PZT 후막의 특성을 증가시키기 위한 공정의 최적화가 필요하다. 침투된 감광성 PZT 졸의 농도, 조사된 UV 시간 및 용매 현상 시간을 최적화한 결과, 0.35 M의 PZT 농도, 4 분의 UV 조사시간과 15 초의 용매 현상시간으로 졸-침투된 PZT 후막은 $800^{\circ}C$ 소결 온도에서 입자들의 성장에 의해 치밀화 정도가 증가되었다. 또한 PZT후막의 강유전 특성(잔류분극 및 항복 전압)도 향상되었다. 특히 잔류분극값은 스크린인쇄된 후막보다 약 4배정도 증가되었다. 이렇게 제작된 후막은 어레이타입의 압전형 마이크로미터크기의 센서 및 액츄에이터 등에 응용 가능성을 제시할 수 있었다.