• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.05b
• /
• pp.557-560
• /
• 2006

In the existed study, a fire outbreak in a reinforced concrete structure looses the organism by the different contraction and expansion of hardened cement pastes and aggregate, and causes cracks by thermal stress, leading to the deterioration of the durability. So accurate diagnosis of deterioration is needed based on mechanism of fire deterioration in general concrete structures. Fundamental information and data on the properties of concrete exposed to high temperature are necessary for accurate diagnosis of deterioration. Therefore, this study is willing to propose fundamental data for accurate diagnosis of deteriorated concrete structure by fire damage with experiment according to the curing conditions.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2014.05a
• /
• pp.256-257
• /
• 2014

Concrete made with ground granulated blast-furnace slag(GGBS) has many advantage, including improved durability, workability and economic benefits. GGBS concrete is that its strength development is considerably slower under standard 20℃ curing conditions than that of portland cement concrete, although the ultimate strength is higher for same water-binder ratio. GGBS is not therefore used in application where high early age strength is required. However, hydration of GGBS is much more sensitive to temperatures, the strength development of GGBS concrete is significantly enhanced.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2002.10a
• /
• pp.83-87
• /
• 2002

Aerospace industries are widely using honeycomb sandwich structures that it has high specific strength and stiffness, chemical material resistance and fatigue resistance. But, in repairing process of damaged areas, one of the problems is that delamination can be occurred in the sound areas during and/or after the exposure to the elevated curing temperature in case that the repair process is repeated. Therefore, this study was conducted Flatwise tensile, Drum peel and Long beam flexural strength tests to evaluate the degree of degradation of mechanical properties of the honeycomb sandwich structures by affecting thermal aging. As the results, the decrease of mechanical strength was observed at the specific specimen which is exposed over 50hrs at $127^{\circ}C$.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07a
• /
• pp.396-398
• /
• 2005

Effects of such factors as polymerization temperature and a newly synthesized oligomeric photoinitiator(PEDI380) on the electro-optic characteristics of polymer/LC composite films prepared by the UV-curing method were investigated. The polymer-dispersed liquid crystal cells were made with oligomeric photoinitiator PEDI380 by UV-curing method exhibited both low driving volta ge($V_90$) and high contrast ratio under optimum formulation condition.

• Proceedings of the KIEE Conference
• /
• 1987.11a
• /
• pp.216-219
• /
• 1987

Dielectric and Mechanical Properties of Mica flake/ Epoxy Composite are investigated. The Mica content is about 50 wt % and its thickness is about $240{\mu}m$. The finished Mica flake/Epoxy Composite contains about 0.1-1.0 wt % of aminosilane coupling agent. Ruby Mica filler and high temperature curing Epoxy resin are used. From the viewpoint of dielectric and mechanical properities. the optimum properties is obtained for the sample post cured at $130^{\circ}C$ for 5 h ours after curing at $80^{\circ}C$ for 2 hours and with 0.5 weight % silane coupling agent.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2004.11a
• /
• pp.321-324
• /
• 2004

The discharge of fly ash that is produced by coal-fired electric power plants is rapidly increasing in Korea. The utilization of fly ash in the raw materials would contribute to the elimination of an environmental problem and to the development of new high-performance materials. So it is needed to study the binder obtained by chemically activation of pozzolanic materials by means of a substitute for the exiting cement. This paper concentrated on the strength development according to the kind of chemical activators, the curing temperature, the heat curing time. Also Scanning electron microscopy and X-Ray diffraction analysis show what the reaction products of the alkali activated fly ash are.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2008.11a
• /
• pp.49-52
• /
• 2008

The present study was to develop a dry PFB method similar to the existing gypsum board construction method in order to apply the existing wet PFB method that uses fire-resistant adhesive. It was found that the existing wet method can produce concrete compressive strength of 80MPa and fire resistance of 3 hours with 30mm PF boards. The goal of development in this study was fire resistance of 3 hours through dry construction of 15mm fire-resistant boards. 1. Improved PF board was prepared by adding inorganic fiber to existing board and using aggregate with grain size of 3mm or less. Molding was done at temperature higher than that for existing PF board molding. While wet curing is used for existing PF boards, this study used dry curing in order to enhance heat insulation performance. 2. According to the results of fire resistance test, when the dry PF method was applied, the temperature of the main reinforcing bar was 116℃ in 15mm, 103.8℃ in 20mm, and 94℃ in 25mm, and these results satisfied the current standards for fire resistance control presented by the Ministry of Land, Transport and Maritime Affairs. When a 3-hour fire resistance test was performed and the external properties of the specimen were examined, the outermost gypsum board hardly remained and internal PF board maintained its form without thermal strain.

• Textile Coloration and Finishing
• /
• v.21 no.4
• /
• pp.39-45
• /
• 2009

PVA films were crosslinked with dimethylol dihydroxy ethylene urea (DMDHEU) and three polycarboxylic acids of butanetetracarboxylic acid (BTCA), citric acid and malic acid Different factors influencing the crosslinking treatment with BTCA were investigated including BTCA and sodium hypophosphite (SHP) concentration, curing temperature and time. The cured films was extracted with boiling water and gel fraction was calculated based on weight change of the PVA films. The gel fraction of PVA films increased with increasing curing temperature and time. And the resistance to water and thermal stability of the crosslinked PVA films improved with the BTCA crosslinking treatment. While crosslinking with citric acid gave the highest gel fraction among the crosslinkers, crosslinking with malic acid showed the highest absorbancy in 0.9% saline solution, which was attributed to lower crosslink density and high number-average molecular weight between crosslinks. The superabsorbent PVA films could be prepared by adjusting the crosslinking condition of PVA with polycarboxilic acids.

• Magazine of the Korea Concrete Institute
• /
• v.10 no.5
• /
• pp.89-100
• /
• 1998

본 연구는 양생온도이력이 콘크리트 강도에미치는 영향을 평가하기 위한 것으로 물 시멘트비가 60%, 45%, 26%인 3종류의 콘크리트에대하여 5$^{\circ}C$부터 5$0^{\circ}C$까지의 항온양생과 초기재령에 고온도이력을 변수로 한 변동온도양생을 실시한 공시체의 압축강도를 측정하였다. 또한 그 실험결과에 강도평가 방법의 하나인 Maturity 개념을 도입하여 강도평가에 미치는 재령, w/c, 온도이력 등에 대한 영향을 평가하였다. 항온양생 실험결과에 따르면 물시멘트비가 낮을수록 초기재령에서의 강도발현은 높게 나타나며 양생온도 5$0^{\circ}C$인 경우를 제외하고 재령7일까지의 강도발현은 양생온도가 높을수록 크게 나타나고 있다. 한편, 변동온도양생실험결과에 의하면 초기재령에서 고온양생한 콘크리트의 강도발현은 물시멘트비의 영향을 크게 받으며, 1주 이후의 양생온도가 강도발현에 미치는 영향은 1주까지의 고온도이력에 대한 영향에 비교해 2차적이다. 기존의 Maturity개념인 Saul-Bergstrom의 함수와 Ooi의 함수를 가지고 항온 및 변동온도 양생실험결과를 분석한 결과, 전체적으로 Saul-Bergstrom식에 의한 경우가 실험값과의 차이가 작게 나타났으나 두 식 모두 Maturity 가 큰 경우에는 계산에 의한 값이 실험에 의한 값보다 크게 나타나고 있어 장기 재령시 강도평가는 한계강도 개념을 고려한 새로운 Matruity함수를 제안할 필요가 있다.

• Design & Manufacturing
• /
• v.16 no.1
• /
• pp.43-49
• /
• 2022

As technologies in various industrial fields develop, high-quality parts are required. In the past, precision parts were produced by the contact machining method, but the contact machining method has clear limitations. In order to solve this problem, research on a non-contact processing method has been conducted, and laser processing and electric discharge processing are representative. However, the non-contact method has a problem in that productivity is insufficient, and there is a problem that it takes a lot of time to continuously process microholes. Researchers have developed an electron beam drilling equipment for continuous processing of fine holes, and a vaporization amplification sheet to increase the processing efficiency of the equipment. In this study, a cylindrical vaporization amplification sheet using room temperature curing type silicon was fabricated, and the metal distribution and thickness uniformity of the produced sheet were analyzed. In order to manufacture a cylindrical vaporization amplification sheet, an equipment capable of using centrifugal force was developed, and a sample in which metal powder was evenly distributed and a constant thickness was produced.