• Korea-Australia Rheology Journal
• /
• v.12 no.1
• /
• pp.55-67
• /
• 2000

In this paper, an experimental study of the rheological behavior of granular flow in a new type of storage silo is presented. The main characteristic of the new design is a hexagonal shape chosen with the objective of minimizing the stresses applied to the stored grains, and to reduce grain damage during the filling and emptying processes. Measurements of stress distribution and flow patterns are shown for a variety of granular materials. Because of the design of the silo, the granular material adopts its natural rest angle at all times eliminating collisional stresses and impacts between grains. A homogeneous, low friction flow is naturally achieved which provides a controlled stress distribution throughout the silo during filling and emptying. Secondary dynamic stresses, which are responsible for wall failure in conventional silos of the vertical type, are completely eliminated. A comparison between the two geometries is presented with data obtained for these silos and a number of granular materials. The discharge pattern inhibits powder formation in the silo and the filling system virtually eliminates unwanted material packing. Finally, notwithstanding the rheological advantages of this new design, the hexagonal cells that constitute the silo have many other advantages, such as the possible use of solar energy to control the humidity inside them. The cell type design allows for versatile storage capabilities and the elevation above the ground provides unlimited transportation facilities during emptying.

• Korean Journal of Materials Research
• /
• v.31 no.9
• /
• pp.481-487
• /
• 2021

ZnO particles are successfully synthesized at 150 ℃ for 30 min using zinc acetate as the Zn source and 1,4-butanediol as solvent using a relatively facile and convenient glycol process. The effect of ammonium hydroxide amounts on the growth behavior and the morphological evolution of ZnO particles are investigated. The prepared ZnO nanoparticle with hexagonal structure exhibits a quasi-spherical shape with an average crystallite size of approximately 30 nm. It is also demonstrated that the morphology of ZnO particles can be controlled by 1,4-butanediol with an additive of ammonium hydroxide. The morphologies of ZnO particles are changed sequentially from a quasi-spherical shape to a rod-like shape and a hexagonal rod shape with a truncated pyramidal tip, exhibiting preferential growth along the [001] direction with increasing ammonium hydroxide amounts. It is demonstrated that much higher OH^- amounts can produce a nano-tip shape grown along the [001] direction at the corners and center of the (001) top polar plane, and a flat hexagonal symmetry shape of the bottom polar plane on ZnO hexagonal prisms. The results indicate that the presence of NH⁴⁺ and OH^- ions in the solution greatly affects the growth behaviors of ZnO particles. A sharp near-band-edge (NBE) emission peak centered at 383 nm in the UV region and a weak broad peak in the visible region between 450 nm and 700 nm are shown in the PL spectra of the ZnO synthesized using the glycol process, regardless of adding ammonium hydroxide. Although the broad peak of the deep-level-emission (DLE) increases with the addition of ammonium hydroxide, it is suggested that the prominent NBE emission peaks indicate that ZnO nanoparticles with good crystallization are obtained under these conditions.

• Korean Journal of Metals and Materials
• /
• v.46 no.3
• /
• pp.169-173
• /
• 2008

Characteristics of etching and induced surface morphology variation by wet-etching of n-type GaN were investigated using phosphoric acidic solutions. Generally, the etch-rate was increased as the temperature of the etch solutions was increased, and the highest etch rate of about $300{\AA}/min$ was achieved at the temperature of $180^{\circ}C$. The morphology variation of the etched surface was observed by optical microscopy and atomic force microscopy. Initially, high density of hexagonal holes or pits were formed on the etched surface at the time of 40 min with the bimodal size of $20{\mu}m$ or $5{\mu}m$, respectively. However, as the etching time was increased further, the lateral size of the hexagonal holes or pits was increased, and finally, joined and merged together at the time of 100 min. This means that the etching of n-type GaN by phosphoric acidic solutions proceeded through the lateral widening and the merging of initial holes and pits.

• Steel and Composite Structures
• /
• v.46 no.4
• /
• pp.539-551
• /
• 2023

In order to study the fire resistance of castellated composite beams with ortho-hexagonal holes and different beam-end restraints, temperature rise tests with constant load were conducted on full-scale castellated composite beams with ortho-hexagonal holes and hinge or rigid joint constraints to investigate the temperature distribution, displacement changes and failure patterns of castellated composite beams with two different beam-end constraints during the whole course of fire. The results show that (1) During the fire, the axial pressure and horizontal expansion deformation generated in the rigid joint constrained composite beam were larger than those in the hinge joint constrained castellated composite beam, and their maximum horizontal expansion displacements were 30.2 mm and 17.8 mm, respectively. (2) After the fire, the cracks on the slab surface of the castellated composite beam with rigid joint constraint were more complicated than hinge restraint, and the failure more serious; the lower flange and web at the ends of the castellated steal beams with hinge and rigid joint constraint produced serious local buckling, and the angles of the ortho-hexagonal holes at the support cracked; the welds at both ends of the castellated composite beam with rigid joint constraint cracked. (3) Based on the simplified calculation method of solid-web composite beam, considering the effect of holes on the web, this paper calculated the axial force and displacement of the beam-end constrained castellated composite beams under fire. The calculation results agreed well with the test results.

• Structural Engineering and Mechanics
• /
• v.89 no.6
• /
• pp.557-570
• /
• 2024

Due to interfacial ageing, chemical action and interfacial damage, the interface debonding may appear in the interfaces of composite laminates. Particularly, the laminates display a side-dependent effect at small scale. In this work, a three-dimensional (3D) and anisotropic thick nanoplate model is proposed to investigate the effects of imperfect interface and nonlocal parameter on the bending deformation, vibrational response and buckling stability of one-dimensional (1D) hexagonal quasicrystal (QC) layered nanoplates. By combining the linear spring model with the transferring matrix method, exact solutions of phonon and phason displacements, phonon and phason stresses of bending deformation, the natural frequencies of vibration and the critical buckling loads of 1D hexagonal QC layered nanoplates are derived with imperfect interfaces and nonlocal effects. Numerical examples are illustrated to demonstrate the effects of the imperfect interface parameter, aspect ratio, thickness, nonlocal parameter, and stacking sequence on the bending deformation, the vibrational response and the critical buckling load of 1D hexagonal QC layered nanoplate. The results indicate that both the interface debonding and nonlocal effect can reduce the stiffness and stability of layered nanoplates. Increasing thickness of QC coatings can enhance the stability of sandwich nanoplates with the perfect interfaces, while it can reduce first and then enhance the stability of sandwich nanoplates with the imperfect interfaces. The biaxial compression easily results in an instability of the QC layered nanoplates compared to uniaxial compression. QC material is suitable for surface layers in layered structures. The mechanical behavior of QC layered nanoplates can be optimized by imposing imperfect interfaces and controlling the stacking sequence artificially. The present solutions are helpful for the various numerical methods, thin nanoplate theories and the optimal design of QC nano-composites in engineering practice with interfacial debonding.

• Journal of Sericultural and Entomological Science
• /
• v.17 no.2
• /
• pp.101-118
• /
• 1975

The pathogenicity of hexagonal and tetragonal cytoplasmic polyhedron virus to one of present leading silkworm varieties, Jam 103${\times}$Jam 104, and its parents, Jam 103 and Jam 104, was investigated. The activation of occult virus by oral inoculation of foreign virus as well as the interference phenomena between the activated and inoculated cytoplasmic polyhedron viruses was observed and the results obtained are as follows. 1. The pathogenicity of cytoplasmic polyhedrosis viruses. 1) There was a high significant difference in the pathogenicity of hexagonal polyhedron virus between the hybrid and its parents showing the lowest infection rate in the hybrid (Jam 103${\times}$Jam 104), medium infection rate in the Japanese line (Jam 103) and the highest infection rate in the Chinese line (Jam 104). In the pathogenicityof tetragonal polyhedron virus, a significant difference was observed only between the hybrid (Jam 103${\times}$Jam 104) and the Chinese line (Jam 104) by showing a higher infection rate in the Chinese line than in the hybrid. 2) The pathogenicity of both hexagonal and tetragonal polyhedron viruses showed a high significant difference in different silkworm instars inoculated by showing a higher infection rate at the second instar than at the fourth instar. 3) The pathogenicity of both hexagonal and tetragonal polyhedron viruses was increased as the concentration of viruses inoculated increased. 2. The phenomena of induction and interference by oral inoculation of foreign virus. 1) The induction rate of cytoplasmic polyhedrosis virus was higher in the parents than in the hybrid. In the parents. a higher rate in the Chinese line than in the Japanese line was observed. 2) The effect of inoculation at different instars on the induction was studied and the induction rate was higher at the second instar inoculated than at the fourth instar inoculated. 3) The degree of activation of hexagonal polyhedron virus with inoculation of tetragonal polyhedron virus was very high when a lower concentration of virus was inoculated and it was very low when a higher concentration of virus was inoculated 4) The degree of activation of tetragonal polyhedron virus with inoculation of hexagonal polyhedron virus was very low when a lower concentration of virus was inoculated and it was not observed when a higher concentration of virus was inoculated. 5) The mixed infection rate with hexagonal and tetragonal polyhedron viruses was higher at the second instar inoculated than at the fourth instar inoculated. 6) It was observed that the secondary hexagonal pc]yhedron virus activated interfered with the primary tetragonal polyhedron virus inoculated when the inoculated concentration of the primary virus is low and the primary virus inoculated interfered with the secondary virus activated when the inoculated concentration of the primary virus is high.

• Journal of the Korean Ceramic Society
• /
• v.46 no.1
• /
• pp.53-57
• /
• 2009

The h-BN powder was synthesized by amorphous $B_2O_3$ and activated carbon at $1550^{\circ}C$ in nitrogen atmosphere, whose properties were examined according to $MgB_6$ addition. Amount of $MgB_6$ addition was varied in the range of $0{\sim}$10\;wt% of the initial mixture. It was observed that $MgB_6$ addition led to an increase in the amount and the grain size of h-BN and decrease in the amount of $B_4C$ forming. When $MgB_6$ added 5 wt%, the amount and crystallinity of h-BN increased as the holding time at the synthesis temperature was prolonged. It was also confirmed that the regularity of three-dimensional ordering of h-BN increases.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.2
• /
• pp.22-27
• /
• 2017

During the water treatment process for household water supply, a reservoir is the last place the water is stored before being supplied to users, and the duration of the water's stay is an important factor that affects its safety. This may cause the concentration of the residual chlorine disinfectant to increase and thus lower the water's quality. The concentration and discharge efficiency of residual chlorine must be verified and managed, because these are key factors that affect the reservoir's performance. Because the actual verification test for analyzing the efficiency of a reservoir and the disinfectant's dilution capacity is difficult, simulations are generally conducted using the computational fluid analysis method. However, the simulation results require validation with experiments. The error and drainage efficiency were analyzed in this study by comparing and analyzing the actual tracer test and simulation so that the actual test for a hexagonal drainage can be replaced by the computational fluid analysis method. Based on the results of the efficiency analysis, the hexagonal reservoir was found to be appropriate, and the simulation's reliability was verified with a tracer test.

• Journal of Powder Materials
• /
• v.6 no.4
• /
• pp.307-313
• /
• 1999

The effect of carbon content on the shape of WC grains dispersed in the Co-rich matrix during liquid phase sintering of WC-35%Co hard metals has been determined. The shape of WC grains was observed using SEM stereography after removing cobalt matrix with boiling hydrochloric acid solution. The WC grains changed from hexagonal to trigonal prism as the carbon content increased in the two-phase region of(WC + $\beta$ - Co), while the morphology of WC grains changed from trigonal to hexagonal shape as the carbon content decreased. The morphology of WC grains changes reversibly along with carbon loss or carbon pick-up. Morphology change of WC grains is attributed to crystal structure of WC, which has an asymmetric array of carbon atoms. There are two types of prismatic planes having different numbers of broken W-C bonds in WC grains. It is scrutinized that as the carbon content increases, the high energy prism planes grow fast and the crystals change from hexagonal to trigonal shape. On the other hand, when the carbon content decreases, the high energy prism planes are dissolved accompanying split of (100) plane into (101) and (101) planes.

• Environmental Engineering Research
• /
• v.20 no.4
• /
• pp.342-346
• /
• 2015

Haloacetonitriles (HANs) are nitrogenous disinfection by-products (DBPs) that have been reported to have a higher toxicity than the other groups of DBPs. The adsorption process is mostly used to remove HANs in aqueous solutions. Functionalized composite materials tend to be effective adsorbents due to their hydrophobicity and specific adsorptive mechanism. In this study, the removal of dichloroacetonitrile (DCAN) from tap water by adsorption on thiol-functionalized mesoporous composites made from natural rubber (NR) and hexagonal mesoporous silica (HMS-SH) was investigated. Fourier-transform infrared spectroscopy (FTIR) results revealed that the thiol group of NR/HMS was covered with NR molecules. X-ray diffraction (XRD) analysis indicated an expansion of the hexagonal unit cell. Adsorption kinetic and isotherm models were used to determine the adsorption mechanisms and the experiments revealed that NR/HMS-SH had a higher DCAN adsorption capacity than powered activated carbon (PAC). NR/HMS-SH adsorption reached equilibrium after 12 hours and its adsorption kinetics fit well with a pseudo-second-order model. A linear model was found to fit well with the DCAN adsorption isotherm at a low concentration level.