• Journal of the Korean Applied Science and Technology
• /
• v.21 no.4
• /
• pp.274-278
• /
• 2004

In this study, hetero-electrode structures have been fabricated to increase luminescence efficiency. The presence of a thin layer of Sn or Ag at the organic-aluminum interface enhanced both electron injection efficiency and electroluminescence when compared to OLEDs using homogeneous electrode. In this paper, the effect of the cathode using Sn/Al hetero electrode structure is observed. Electric properties of the OLED using Sn/Al hetero cathode are improved in comparison of only Al cathode. The hetero-electrode existing different energy level induces the advanced structure of OLED can accumulate electron density. The luminescence efficiency of OLED with Sn/Al of Ag/Al cathode is higher because of their higher electron injection efficiency. And, the turn on voltage of the OLED device using Sn thin layer is lowest as about 10 V.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.10 no.3
• /
• pp.78-85
• /
• 1996

This paper experience the mechanism for the electret of polyethyleneterephthalate(PET) by using surface potentail measurement means. We investigated the internal charge production and becoming week by evaporating electrode in sample structure of electret coexist with hetero charge and homo charge, as the study based on two charge theory. We expects that the hetero charge consists of the dipole and ion displacement of internality, the homo charge consists of injected charge of externality.

• Proceedings of the KIEE Conference
• /
• 1987.11a
• /
• pp.511-514
• /
• 1987

Langmuir-Blodgett (LB) films of TCNQ(tetracyanoquinodimethane) with alkyl radical($C_{12}TCNQ$) were prepared on the sample of Al/LB film/Al type where Al are electrode, and polarization in LB film and dipolar moment of molecules in the films were measured by TSC. $Al_2O_3$ layer was yielded on the electrode by natural oxidation in air. According to the cooperation of $Al_2O_3$ dielectric layer and the polarization of $C_{12}TCNQ$-LB film, the macroscopic electrical field was yielded in LB film and $Al_2O_3$ layer. The field strength in $C_{12}TCNQ$-LB films was evaluated at about $1{\times}10^6{\sim}5{\times}10^6\;V/cm$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1995.11a
• /
• pp.240-243
• /
• 1995

The basic electrochemical and photochemical behavior of ultrathin mono- and hetero-type LB film of amphiphilic Ru bipyridine complex adsorbed on ITO electrode by the Langmuir- Blodgett(LB) method as monolayer and alternating multilayer state. With theoretical equation of cyclic voltammetry for redox species, the cyclic voltammogram were simulated successfully taking account the interaction parameters. We could fit almost all measured voltammograms with k$^{\circ}$=72s$\^$-1/, ${\alpha}$$\sub$a/=0.44, ${\alpha}$$\sub$c/=0.54, $\Gamma$$\sub$T/=1.4${\times}$10$\^$-10/, k=0.015s$\^$-1/ values. The AFM images of mono and hetero type LB film surfaces on ITO were also studied.

• Membrane Journal
• /
• v.26 no.3
• /
• pp.229-237
• /
• 2016

We prepared heterogeneous ion exchange membranes (hetero-IEMs) for the application of membrane capacitive deionization (MCDI). Hetero-IEMs were fabricated by compressing the mixture of ion exchange resin powders and liner low density polyethylene (LLDPE). Characterization and MCDI desalination experiments were carried for the fabricated membranes. Electrical resistance of membrane decreased and water content increased with increasing the resin content in the hetero-IEMs. However, transport number indicating permselectivity of membrane was similar with that of commercial homogenesous ion exchange membrane. The results of MCDI desalination experiments showed that the adsorption amount for hetero-IEM was about 90% of that of homogeneous membrane due to the high electrical resistance of hetero-IEM. Although desalination performance of hetero-IEM decreased compared with homogeneous membrane, it was thought to be applicable to MCDI because of simple preparation and low price.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.3
• /
• pp.250-254
• /
• 2006

Hetero-junction sheet actuator composed of carbon nanotubes and $V_{2}O_5$ nanowires were demonstrated in a bimetal configuration. The successive filtration of $V_{2}O_5$ nanowire solution followed by carbon nanotube dispersed water solution in the same way produced a dark-gray colored sheet. A significant actuation was observed in sodium chloride electrolyte solution with a bending direction to the carbon nanotube side at the positive bias voltage against the copper counter-electrode. As the frequency of the applied voltage increased, the amplitudes decreased, indicating a rather slow response of the hetero-film actuator in the electrolyte solution. The hybrid structure enabled an easy fabrication of the film actuator with the enhanced efficiencies.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2008.05a
• /
• pp.29-32
• /
• 2008

The electron charging and degradation of anode phosphor layers are showed major problems in high electric field with anode electrode of field emission devices. An AI metal layer on the phosphor layer may get rid of these problems. This Hetero-metal-oxide phosphor layer are formed with the roughness of phosphor surface layer without interlayer and cannot be given rise to enhance the luminance efficiency. In order to enhance the brightness, an anode layer need to be flated between phosphor layer and AI metal layer in anode electrode. After optimizing the anode phosphor layer, an anode layer with AI metal and inter layer increased the brightness and luminescence efficiency 1.2 times more than only phosphor laver in anode.

• Journal of the Semiconductor & Display Technology
• /
• v.13 no.2
• /
• pp.1-5
• /
• 2014

Transparent and conducting aluminum-doped ZnO electrodes were fabricated by atomic layer deposition methods. The electrode showed the lowest resistivity of $5.73{\times}10^{-4}{\Omega}cm$ at a 2.5% cyclic layer deposition ratio of Trimethyl-aluminum and Diethyl-zinc chemicals. The electrodes showed minimum resistivity when deposited at a temperature of $225^{\circ}C$. The electrode also showed optical transmittance of about 92% at 300 nm. An organic solar cell made with a 300-nm-thick aluminum-doped ZnO electrode exhibited 2.0% power conversion efficiency.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.36 no.5
• /
• pp.339-345
• /
• 1987

In the region of high temperature, a very appreciable short-circuit current Is was observed from M1(A1)-P(PET)-M2(Cu) system sandwitched with hetero metals without applying external field. The short-circuit current Is is greatly dependent on electrode material and it has been certified by measuring open-circuit voltage. From these experimental results, we can see that Is is due to electro-chemical action in M-P interface. In this electro-chemical reaction,the generation reaction and the solution reacftion of the oxidies from electrode are probably co-exist and the measured values of the open-circuit voltage was almost correspond to those calculated from Nernst equation.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.160-160
• /
• 2016

In this study, we applied the low temperature curing Ag paste to replace PVD System. The electrode formation of low temperature curing Ag paste for silicon Hetero-junction solar cells is important for improving device characteristics such as adhesion, contact resistance, fill factor and conversion efficiency. The low temperature curing Ag paste is composed various additives such as solvent, various organic materials, polymer, and binder. it depends on the curing temperature conditions. The adhesion of the low temperature curing Ag paste was decided by scratch test. The specific contact resistance was measured using the transmission line method. All of the Ag electrodes were experimented at various curing temperatures within the temperature range of $160^{\circ}C-240^{\circ}C$, at $20^{\circ}C$ intervals. The curing time was also changed by varying the conditions of 10-50min. In the optimum curing temperature $200^{\circ}C$ and for 20 min, the measured contact resistance is $19.61m{\Omega}cm^2$. Over temperature $240^{\circ}C$, confirmed bad contact characteristic. We obtained photovoltaic parameter of the industrial size such as Fill Factor (FF), current density (Jsc), open-circuit voltage (Voc) and convert efficiency of up to 76.2%, 38.1 mA/cm2, 646 mV and 18.3%, respectively.