• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.17 no.3
• /
• pp.232-242
• /
• 2005

It has been recognized that solar water heating systems are economically inferior to conventional gas water-heaters and boilers using light oil as fuel in spite of having practical possibilities among other alternative energy facilities in Korea. The solar system, however, should be revaluated due to the sharp rise of oil prices recently. We have calculated the energy amount and cost through a series of research projects for the system by experiment and simulation, which lead to analyzing reliable life cycle costs. For the economic analysis, the gas water-heater and light oil boiler were taken as base cases while the solar systems implemented with these facilities were compared as alternatives. As a result, the solar system using the light oil as an auxiliary fuel surpassed the light oil boiler in economics. And a $50\%$ government subsidy for the initial cost is needed to maintain competitiveness with the gas hot-water heater. With this support, the simple payback period of the system can approach 12.8 years under $20\%$ additional curtailment of expenditure.

• Journal of Energy Engineering
• /
• v.16 no.4
• /
• pp.194-201
• /
• 2007

HHV (Higher Heating Value) of biomass fuel is calculated by using ultimate analysis data and has been proposed by using correlation equation, and compared with the experiment the adequacy about each correlation equation with measured HHV and examined. Samples used for experiment are prepared by mixing biomass (i.e. rice husk and sawdust) with organic waste (i.e. polystyrene polypropylene and waste paper) of 10, 30, 50 wt% of composition. Ultimate analysis and measurement of HHV are respectively measured by using KS standard method. The average error value of estimated HHV results is about 880 kJ/kg(about 3.8% of measured HHV). The corresponding correlation coefficients ($R^2$) of experimental result and estimated HHV result are $0.957{\sim}0.996$.

• Journal of Bio-Environment Control
• /
• v.31 no.4
• /
• pp.468-475
• /
• 2022

This study was conducted to find out the efficiency of heating initiative temperature and carbon dioxide fertilization in summer squash (Cucurbita moschata D.). The heating start temperature experiment was performed at 9℃, 12℃, and 15℃ using an electric heater and operated when the temperature was lower than the target temperature. The CO₂ fertilization concentration experiment was performed from 7 to 12 with the control, 500 µmol·mol^-1, and 800 µmol·mol^-1 using liquefied carbon dioxide. Investigation items were plant height, stem diameter, number of leaves, leaf area, fresh weight, dry weight, also economic analysis was conducted by surveying only fruits exceeding 100 g. Photosynthesis was measured for the upper leaf position to calculate the saturation point according to the control. The photo saturation point was 587 µmol·m^-2·s^-1, and the CO₂ saturation point was 702 µmol·mol^-1. A_max values by carbon dioxide were 13.4, 17.8, 17.2, 19.6, and 17.5 µmolCO₂·m^-2·s^-1 in the order of 9℃, 12℃, 15℃, 500 µmol·mol^-1, and 800 µmol·mol^-1. In the temperature experiment, 9℃ in growth did not grow normally and no fruiting was performed. 12℃ and 15℃ were higher than 9℃, but there was no significant difference in growth and production. The CO₂ fertilization experiment showed no significant difference between the treatment in growth, but the productivity of 800 µmol·mol^-1 was the best. Comprehensively, the heating initiative temperature of 15℃ was good for crop growth and production, but there is no significant difference from 12℃, so it is good to set the heating start temperature to 12℃ economically, and maintaining of 800 µmol·mol^-1 is effective in increasing production.

• Journal of Radiopharmaceuticals and Molecular Probes
• /
• v.3 no.1
• /
• pp.38-43
• /
• 2017

Tc-99m labeled sestamibi ($^{99m}Tc$-MIBI) is one of most widely used radiopharmaceuticals for myocardial SPECT imaging. Radiolabeling of $^{99m}Tc$-MIBI is recommended by heating in $100^{\circ}C$ water bath for 15 min. However, the water bath might be a source of contamination. Thus, if radiolabeling of $^{99m}Tc$-sestamibi can be performed at room temperature, then it would be more convenient to use in clinical application. In this study, we performed the radiolabeling of $^{99m}Tc$-MIBI in different temperature conditions or using different instruments to find out the efficient labeling condition. We studied the $^{99m}Tc$-MIBI labeling at room temperature or $100^{\circ}C$ heating block, and checked the labelling yields every 1 min for 10 min using radio-TLC with 2 different eluents-saline and acetone. From the experiment, we confirmed that the $^{99m}Tc$-MIBI can be labeled over 90% yield but not completed at room temperature. However, the $^{99m}Tc$-MIBI labeling was completed when it was performed in the $100^{\circ}C$ heating block. Finally, we proved that heating is essential for complete $^{99m}Tc$-MIBI labelling, furthermore using heating block is also possible instead of water bath.

• Journal of The Association for Neo Medicine
• /
• v.1 no.1
• /
• pp.103-113
• /
• 1996

It is thought that the quantity and quality of the heat stimulation and the mechanism of heating process are important to understand the moxa-combustion. In order to get the basic data on the effective moxa-combustion method, combustion temperature changes (average temperature, peak temperature, average gradient temperature and maximum gradient temperature) of the heating period were measured respectively by the density of moxa material. For the experiment, samples of $300mg/0.26cm^3$ , $400mg/0.26cm^3$ and $500mg/0.26cm^3$ of moxa material were molded in a conical mold with each 10mm in diameter and height. 1. The average temperature and peak temperature of heating period on the moxa-combustion showed higher in the $400mg/0.26cm^3$ and $300mg/0.26cm^3$ than in the $500mg/0.26cm^3$ sample respectively. 2. The average gradient temperature of heating period on the moxa-combustion rose quickly in the $300mg/0.26cm^3$, $400mg/0.26cm^3$ and $500mg/0.26cm^3$ in that order and the maximum gradient temperature rose more quickly in the $300mg/0.26cm^3$ and $400mg/0.26cm^3$ than in the $500mg/0.26cm^3$ sample respectively. According to the above results, it is concluded that the density of moxa material is (the) more important (factor) than the weight or volume of moxa material on the combustion temperature changes of the heating period for the evaluation of the quality and quantity of moxa-combustion.

• Korean Journal of Materials Research
• /
• v.8 no.11
• /
• pp.987-992
• /
• 1998

Titanium aluminide intermetallic compound was formed from high purity elemental Ti and A1 foils by selfpropagating, high-temperature synthesis(SHS1 in hot press. Formation of $TiAl_3$ intermetallics at the interface between Ti and Al foil was observed to be controlled by temperature, pressure and heating rate. Especially, the heating rate is the most important role to form intermetallic compound by SHS reaction. According to DTA experiment, the SHS reactions appeared at two different temperatures below and above the melting point of Al. It was also observed that both SHS reaction temperatures increased with increasing the heating rate. After the SHS reaction of alternatively layered 10 Ti and 9 A1 foils at the heating rate of $20^{\circ}C$/min, the $700\mu\textrm{m}$ thick titanium aluminide sheet was formed by heat treatment at $810^{\circ}C$ for 4hours.

• Economic and Environmental Geology
• /
• v.50 no.2
• /
• pp.159-170
• /
• 2017

The temporal and spatial temperature distribution of the heat storage mortar made of porous feldspar was measured and the thermal properties and electricity consumption were analyzed. For the experiment, two real size chambers (control model and test model) with hot water pipes were constructed. Two large scale models with hot water pipes were constructed. The surface temperature change of the heat storage layer was remotely monitored during the heating and cooling process using infrared thermal imaging camera and temperature sensor. The temperature increased from $20^{\circ}C$ to $30^{\circ}C$ under the heating condition. The temperature of the heat storage layer of the test model was $2.0-3.5^{\circ}C$ higher than the control model and the time to reach the target temperature was shortened. As the distance from the hot water pipe increased, the temperature gap increased from $4.0^{\circ}C$ to $4.8^{\circ}C$. The power consumed until the surface temperature of the heat storage layer reached $30^{\circ}C$ was 2.2 times that of the control model. From the heating experiment, the stepwise temperature and electricity consumption were calculated, and the electricity consumption of the heat storage layer of the test model was reduced by 66%. In the cooling experiment, the surface temperature of the heat storage layer of the test model was maintained $2^{\circ}C$ higher than that of the control model. The heat storage effect of the porous feldspar mortar was confirmed by the temperature experiment. With considering that the time to reheat the heat storage layer is extended, the energy efficiency will be increased.

• The Journal of the Convergence on Culture Technology
• /
• v.7 no.3
• /
• pp.553-564
• /
• 2021

This study analyzed the the risk of halogen lamp for pigsty heating and its fire prevention. Halogen lamps are used for keeping warm in pen because of their excellent economy and convenience. However, there is a high risk of fire due to poor safety management and exposure to animal movements. In fact, after exploring old pigsty and cattle shed, it was easy to confirm that they were exposed to fire risks. We noted this point and studied the possibility of fire by experiment due to combustible contact with halogen lamp and carelessness in use. The experiment was conducted under conditions similar to the actual use environment. After installing halogen lamps to the height used in actual pen, the temperature change was observed with infrared camera with straw, sawdust and rice husks on the floor. And assuming abnormal conditions, the experiment was also conducted under conditions the lamp dropped on the floor or combustible material came into contact with the glass tube inside the lamp. If halogen lamps were used in normal condition, there was no risk of fire. However, in abnormal use environments, smoke comes out or even ignited. Even if it is convenient for use or highly utilized, high risk of fire will require setting up fire prevention measures or regulation of use. Through in-depth fire investigation and research, we should promote the risk of fire and make efforts to prevent fire to minimize human life and property damage.

• KIEAE Journal
• /
• v.17 no.4
• /
• pp.33-39
• /
• 2017

Purpose: The use of renewable energy system is essential for building energy independence and saving energy consumption in the building sector. Among renewable energy technologies, ground source heat pump(GSHP) system is more energy-efficient and environmental-friendly than other heat source systems due to utilize stable ground heat source. However, the GSHP system requires a high initial installation cost and installation space in limited urban area, so it is difficult to have superiority in the market of heat source system. Therefore, it is necessary to develop the installation method of low-cost and improve system performance. This paper aims to evaluate the performance of double u-tube ground heat exchanger(GHX) and verify system feasibility through real-scale experiment. Method: In this study, the real-scale experiment of vertical closed-type GSHP system was conducted using double u-tube GHX and high-efficiency grout. Through the verification experiment, heat source temperature, heat exchange rate(HER) and seasonal performance factor(SPF) were measured according to the long-term operation. In addition, the feasibility analysis was conducted comparing to the single u-tube system. Result: In the results of experiment, average HER was 136.27 W/m and average SPF was 5.41. Furthermore, compared to the single u-tube, the installation cost of the developed system could be reduced about 70% in the same heating load condition.

• The Korea Journal of Herbology
• /
• v.26 no.2
• /
• pp.25-30
• /
• 2011

Objectives : This study was carried out to investigate an antioxidant ability, the change of antioxidant ability, antimicrobial activity and anticancer in functional meat ball and sausage prepared from Lentinus edoes mycelium and texturized soy protein. Methods : This experiments was carried out to investigate antioxidant ability(TBARS, DPPH, SOD-like ability), antibacterial activity and anticancer ability using sarcoma 180 extracts from Lentinus edoes mycelium. Result : Anticancer ability of Lentinus edoes mycelium showed a 28% survival rate and 63% of inhibition rate of tumor, which showed $1.30{\pm}0.4g$ of tumor weight. These results revealed an effective Lentinus edoes mycelium resources as anticancer sources. After heating peoducts prepared from Lentinus edoes mycelium, these products doesn't showed difference between after heating and before heating in measuring of SOD-like activity and DPPH. In DPPH experiment, ethanol extracts showed a high DPPH value as 90.85%, but hot water extracts showed 82.14% in DPPH value. Conclusion : In conclusion, it is very useful resources for preparing functional food on the basis of results from antioxidant(TBARS, DPPH, SOD-like ability), antibacterial activity and anticancer ability using sarcoma 180.