• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.47 no.2
• /
• pp.9-17
• /
• 2010

Recently, there has been much interest in orthogonal frequency division multiplexing (OFDM) for next generation wireless wideband communication systems. OFDM is a special case of multicarrier transmission, where a single data stream is transmitted over a number of lower-rate subcarriers. One of the main reasons to use OFDM is to increase robustness against frequency-selective fading or narrowband interference. However, in the radio systems it is also important to distortion introduced by high power amplifiers (HPA's) such as solid state power amplifier (SSPA) considered in this paper. Since the signal amplitude of the OFDM system is Rayleigh-distributed, the performance of the OFDM system is significantly degraded by the nonlinearity of the HPA in the OFDM transmitter. In this paper, we propose a canonical piecewise-linear (PWL) model based digital predistorter to prevent signal distortion and spectral re-growth due to the high peak-to-average power ratio (PAPR) of OFDM signal and the nonlinearity of HPA's. Computer simulation on an OFDM system under additive white Gaussian noise (AWGN) channels with QPSK, 16-QAM and 64-QAM modulation schemes and modulator/demodulator implemented with 1024-point FFT/IFFT, demonstrate that the proposed predistorter achieves significant performance improvement by effectively compensating for the nonlinearity introduced by the SSPA.

• Journal of the Korean Chemical Society
• /
• v.61 no.1
• /
• pp.29-33
• /
• 2017

Formation of Au particles in nonstoichiometric $Cu_{2-x}{^I}Cu{_2}^{II}O_{3-{\delta}}$ ($x{\approx}0.20$; ${\delta}{\approx}0.10$) oxide from aniline + hydrochloric acid mixtures and chloroauric acid in the ratios 30 : 1; 60 : 1; 90 : 1 (S1-S3) by volume and 0.01 mol of copper acetate, $Cu(OCOCH_3)_2.H_2O$, in each case is performed by sol-gel growth. Powder x-ray diffraction (XRD) results show Au particles are dispersed in tetragonal nonstoichiometric dicopper (I) dicopper (II) oxides, $Cu_{2-x}{^I}Cu{_2}^{II}O_{3-{\delta}}$ ($x{\approx}0.20$; ${\delta}{\approx}0.10$). Average crystallite sizes of Au particles determined using Scherrer equation are found to be in the approximate ranges ${\sim}85-140{\AA}$, ${\sim}85-150{\AA}$ and ${\sim}80-150{\AA}$ in S1-S3, respectively which indicate the formation of Au nano-micro size particles in $Cu_{2-x}{^I}Cu{_2}^{II}O_{3-{\delta}}$ ($x{\approx}0.20$; ${\delta}{\approx}0.10$) oxides. Hysteresis behaviour at 300 K having low loop areas and magnetic susceptibility values ${\sim}5.835{\times}10^{-6}-9.889{\times}10^{-6}emu/gG$ in S1-S3 show weakly ferromagnetic nature of the samples. Broad and isotropic electron paramagnetic resonance (EPR) lineshapes of S1-S4 at 300, 77 and 8 K having $g_{iso}$-values ${\sim}2.053{\pm}0.008-2.304{\pm}0.008$ show rapid spin-lattice relaxation process in magnetic $Cu^{2+}$ ($3d^9$) sites as well as delocalized electrons in Au ($6s^1$) nano-micro size particles in the $Cu_{2-x}{^I}Cu{_2}^{II}O_{3-{\delta}}$ ($x{\approx}0.20$; ${\delta}{\approx}0.10$) oxides. Broad and weak UV-Vis diffuse reflectance optical absorption band ~725 nm is assigned to $^2B_{1g}{\rightarrow}^2A_{1g}$ transitions, and the weak band ~470 nm is due to $^2B_{1g}{\rightarrow}^2E_g$ transitions from the ground state $^2B_{1g}$(${\mid}d_{x^2-y^2}$>) of $Cu^{2+}$ ($3d^9$) ions in octahedral coordination having tetragonal distortion.

• Journal of the Korean Ceramic Society
• /
• v.43 no.11 s.294
• /
• pp.715-723
• /
• 2006

Perovskite oxide materials are very important for the electronics industry, because they exhibit promising properties. With an interest in the obvious applications, significant effort has been invested in the growth of highly crystalline epitaxial perovskite oxide thin films in our laboratory. And the desired structure of films was formed to achieve excellent properties. $Y_1Ba_2Cu_3O_{7-x}$ (YBCO) superconducting thin films were simultaneously deposited on both sides of 3 inch wafer by inverted cylindrical sputtering. Values of microwave surface resistance R$_2$ (75 K, 145 GHz, 0 T) smaller than 100 m$\Omega$ were reached over the whole area of YBCO thin films by pre-seeded a self-template layer. For implementation of voltage tunable high-quality varactor, A tri-layer structured SrTiO$_3$ (STO) thin films with different tetragonal distortion degree was prepared in order to simultaneously achieve a large relative capacitance change and a small dielectric loss. Highly a-axis textured $Ba_{0.65}Sr_{0.35}TiO_3$ (BST65/35) thin films was grown on Pt/Ti/SiO$_2$/Si substrate for monolithic bolometers by introducing $Ba_{0.65}Sr_{0.35}RuO_3$ (BSR65/35) thin films as buffer layer. With the buffer layer, the leakage current density of BST65/35 thin films were greatly reduced, and the pyroelectric coefficient of $7.6\times10_{-7}$ C $cm^{-2}$ $K^{-1}$ was achieved at 6 V/$\mu$m bias and room temperature.

• The Plant Pathology Journal
• /
• v.18 no.6
• /
• pp.313-316
• /
• 2002

Systemic virus symptoms caused by a Potexvirus were observed on leaves of infected hosta (Hasta spp.) plants cultivated in Seoul, Korea. Symptoms on diseased hosta plants include mosaic, mottle, irregular blotchy patches, and chlorotic spots on or distortion of the leaves. No other viruses, such as Cucumber mosaic virus, Lily symptomless virus, or Potyvirus, were detected from the same plants by electron microscopy and by Western blot and RT-PCR analyses, indicating that they were singly infected by the potexvirus. The symptoms differed among cultivars and species of hosta, and affected the quality of plants for commercialization, as well as, plant growth and flowering of susceptible cultivars. Most of the cultivars and species investigated were susceptible to the virus, while some were not infected by the virus at all. Purified virus particles were of filamentous type with unaggregated forms 540 nm in length, which is a typical potexviral morphology. The virus consisted of a single-stranded RNA molecule of 6 kb long for genome and single component of coat protein (CP) about 27 kDa. The CP strongly reacted with the antiserum against Hosta vims X (HVX), suggesting that the virus is an isolate of HVX. This is the first report of the occurrence and identification of HVX from hosta plants in Korea.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.4C
• /
• pp.403-413
• /
• 2009

We compare three predistortion methods to prevent signal distortion and spectral re-growth due to the high PAPR (peak-to-average ratio) of OFDM signal and the non-linearity of high-power amplifiers. The three predistortion methods are pth order inverse, indirect learning architecture and look up table. The pth order inverse and indirect learning architecture methods requires less memory and has a fast convergence because these methods use a polynomial model that has a small number of coefficients. Nevertheless the convergence is fast due to the small number of coefficients and the simple computation that excludes manipulation of complex numbers by separate compensation for the magnitude and phase. The look up table method is easy to implement due to simple computation but has the disadvantage that large memory is required. Computer simulation result reveals that indirect learning architecture shows the best performance though the gain is less than 1 dB at $BER\;=\;10^{-4}$ for 64-QAM. The three predistorters are adaptive to the amplifier aging and environmental changes, and can be selected to the requirements for implementation.

• Nuclear Engineering and Technology
• /
• v.52 no.11
• /
• pp.2585-2593
• /
• 2020

Swift heavy ion (SHI) beam irradiation can generate desirable defects in materials by transferring sufficient energy to the lattice that favours huge possibilities in tailoring of materials. The effect of Ag¹⁵⁺ ion irradiation with energy 200 MeV on spray deposited V₂O₅ thin films of thickness 253 nm is studied at various ion doses from 5 × 10¹¹ to 1 × 10¹³ ions/㎠. The XRD results of pristine film confirmed orthorhombic structure of V₂O₅ and its average crystallite size was found to be 20 nm. The peak at 394 cm^-1 in Raman spectra confirmed O-V-O bonding of V₂O₅, whereas 917 cm^-1 arise because of distortion in stoichiometry by a loss of oxygen atoms. Raman peaks vanished completely above the ion fluence of 5 × 10¹² ions/㎠. Optical studies by UV-Vis spectroscopy shows decrement in transmittance with an increase in ion fluence up to 5 × 10¹² ions/㎠. The red shift is observed both in the direct and indirect band gaps until 5 × 10¹² ions/㎠. The surface topography of the pristine film revealed sheath like structure with randomly distributed spherical nano-particles. The roughness of film decreased and the density of spherical nanoparticles increased upon irradiation. Irradiation improved the conductivity significantly for fluence 5 × 10¹¹ ions/㎠ due to band gap reduction and grain growth.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.2C
• /
• pp.191-199
• /
• 2006

In this paper, we propose a method to implement a predistorter of the $rho$-th order inverse filter structure to prevent signal distortion and spectral re-growth due to the high PAPR (peak-to-average ratio) of the OFDM signals and the non-linearity of high-power amplifiers. We model the memory-less non-linearity of the high-power amplifier with a polynomial model and utilize the inverse of the model, the $rho$-th order inverse filter, for the predistorter. Once the non-linearity is modeled with a polynomial, since we can determine the $rho$-th order inverse filter only with the coefficients of the polynomial, large memory is not required. To update the coefficients of the non-linear high-power amplifier model, we can use LMS or RLS algorithms. The convergence speed is high since the number of coefficients is small, and the computation is simple since manipulation of complex numbers is not necessary.

• The Bulletin of The Korean Astronomical Society
• /
• v.41 no.1
• /
• pp.45.1-45.1
• /
• 2016

Spatially rotating magnetic fields have been observed in the solar wind and in the Earth's magnetopause as well as in reversed field pinch (RFP) devices. Such field configurations have a similarity with extended current layers having a spatially varying plasma pressure instead of the spatially varying guide field. It is thus expected that magnetic reconnection may take place in a rotating magnetic field no less than in an extended current layer. We have investigated the spontaneous evolution of a collisionless plasma system embedding a rotating magnetic field with a two-and-a-half-dimensional electromagnetic particle-in-cell (PIC) simulation. In magnetohydrodynamics, magnetic flux can be decreased by diffusion in O-lines. In kinetic physics, however, an asymmetry of the velocity distribution function can generate new magnetic flux near O- and X-lines, hence a dynamo effect. We have found that a magnetic-flux-reducing diffusion phase and a magnetic-flux-increasing dynamo phase are alternating with a certain period. The temperature of the system also varies with the same period, showing a similarity to sawtooth oscillations in tokamaks. We have shown that a modified theory of sawtooth oscillations can explain the periodic behavior observed in the simulation. A strong guide field distorts the current layer as was observed in laboratory experiments. This distortion is smoothed out as magnetic islands fade away by the O-line diffusion, but is soon strengthened by the growth of magnetic islands. These processes are all repeating with a fixed period. Our results suggest that a rotating magnetic field configuration continuously undergoes deformation and relaxation in a short time-scale although it might look rather steady in a long-term view.

• Korean Journal of Agricultural Science
• /
• v.47 no.3
• /
• pp.533-544
• /
• 2020

In this paper, we conducted a dynamic ex-post assessment on the grape business cessation support System. Based on the analysis results, in the short term, there was an increase in grape price due to a decrease in production and accompanying increases in the prices of consumption substitution items. However, in the long run, grape prices fell again due to an increase in grape production because of the entry of new grape farmers and the growth of adult grape trees. In addition, the analysis showed that the balloon effect caused by the conversion of crops caused indirect damage such as an increase in the production volume of substitution crops and a decrease in prices. When analyzing the social welfare measurement, the results showed that the support system for business cessation increased the overall social welfare due to an increase in producer welfare because of a price increase in the short term, but in the long term, both producer and consumer welfare decreased. In the end, it is necessary to review the system because the government's intervention may cause market distortion and inefficient resource allocation. Above all, it is necessary to minimize the indirect effect of the industry's contraction and balloon effect due to excessive business cessation. For this, conditional support should be provided in parallel with post management rather than unconditional support. In addition, it is necessary to provide a strategic support system that considers substitution items in addition to those items to be supported.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.5
• /
• pp.53-64
• /
• 2012

Deep and narrow welds can be produced by laser welding at high welding speeds with a narrow heat-affected zone (HAZ) and little distortion of the workpiece. This study aims to evaluate the usefulness of laser welding at automobile component manufacture. Microstructure observation, hardness test, tensile test and fatigue life test are performed by using the fiber laser welded SPFC590 steel sheets which is used widely in the manufacture of automotive seat frame. Three kinds of specimens are only a SPFC590 steel plate, quasi-butt joint plate and lap joint plate by laser welding. The following results that will be helpful to understand the static strength, fatigue crack initiation and growth mechanism were obtained. (1) The tensile strength of quasi butt joint specimens nearly equal to base metal specimens, but lap joint specimens fractured in shear area of weld metal. (2) The fatigue strength of quasi-butt joint specimen was approximately 8 percent lower than that of the base metal specimens. Furthermore, the lap joint specimens were less than 86 percent of the base metal specimens. (3) The lap joint fatigue specimens fractured at shear area in high level stress amplitude, while fractured at normal area in low level stress amplitude. From these results, the applicability of the laser welding to the automobile component is discussed.