• Journal of the Korean Applied Science and Technology
• /
• v.35 no.4
• /
• pp.1108-1119
• /
• 2018

As the interest on the air pollution is gradually rising at home and abroad, automotive and fuel researchers have been studied on the exhaust and greenhouse gas emission reduction from vehicles through a lot of approaches, which consist of new engine design, innovative after-treatment systems, using clean (eco-friendly alternative) fuels and fuel quality improvement. This research has brought forward two main issues : exhaust emissions (regulated and non-regulated emissions, PM particle matter) and greenhouse gases of vehicle. Exhaust emissions and greenhouse gases of automotive had many problem such as the cause of ambient pollution, health effects. In order to reduce these emissions, many countries are regulating new exhaust gas test modes. Worldwide harmonized light-duty vehicle test procedure (WLTP) for emission certification has been developed in WP.29 forum in UNECE since 2007. This test procedure was applied to domestic light duty diesel vehicles at the same time as Europe. The air pollutant emissions from light-duty vehicles are regulated by the weight per distance, which the driving cycles can affect the results. Exhaust emissions of vehicle varies substantially based on climate conditions, and driving habits. Extreme outside temperatures tend to increasing the emissions, because more fuel must be used to heat or cool the cabin. Also, high driving speeds increases the emissions because of the energy required to overcome increased drag. Compared with gradual vehicle acceleration, rapid vehicle acceleration increases the emissions. Additional devices (air-conditioner and heater) and road inclines also increases the emissions. In this study, three light-duty vehicles were tested with WLTP, NEDC, and FTP-75, which are used to regulate the emissions of light-duty vehicles, and how much emissions can be affected by different driving cycles. The emissions gas have not shown statistically meaningful difference. The maximum emission gas have been found in low speed phase of WLTP which is mainly caused by cooled engine conditions. The amount of emission gas in cooled engine condition is much different as test vehicles. It means different technical solution requires in this aspect to cope with WLTP driving cycle.

• Journal of Bio-Environment Control
• /
• v.32 no.4
• /
• pp.302-311
• /
• 2023

This study aimed to investigate the changes in bioactive compounds across the ripening stages of three pepper cultivars, each characterized by unique skin colors. The samples used in this study consisted of three pepper cultivars distinguished by their skin colors as green, purple, and yellow green at breaker ripening stage. Samples were harvested at each of the four ripening stages, including premature, breaker, turning, and mature, and subjected to analysis for various bioactive compounds, including capsaicin, ascorbic acid, kaempferol, quercetin, and sugars. In all cultivars with varying skin colors, the capsaicin content within green pepper fruits consistently increased as the ripening stages advanced. Ascorbic acid was most abundant during the premature stage of development in purple and green cultivars, subsequently declining as maturation progressed. In the case of the purple cultivar, kaempferol content decreased by approximately 30% at the mature stage, while the green cultivar exhibited a gradual increase in kaempferol content with maturation. Conversely, the kaempferol content of the yellow green cultivar rapidly declined as maturation progressed. Regarding quercetin content, the purple and green cultivars tended to decrease with maturity, while the yellow green cultivar displayed an increasing trend. Furthermore, the accumulation patterns of glucose, fructose, and sucrose, the predominant free sugars in green pepper fruit, demonstrated an inclination to increase as the maturation stage advanced in both purple and green cultivars. In contrast, the yellow green cultivar initially showed an elevation in free sugar content during the immature stage, followed by a minor reduction during maturation and a subsequent rise during the mature stage. Each pepper cultivar, distinguished by its unique skin color, exhibits varying levels of bioactive substances at different ripening stages. Therefore, optimal harvesting and utilization should align with periods when the desired substance content is at its peak.

• Journal of Oral Medicine and Pain
• /
• v.31 no.1
• /
• pp.1-16
• /
• 2006

The most important progress in diagnostic sciences is the increased sensitivity and specificity in diagnostic procedures due to the development of micromethodologies and increasing availability of immunological and molecular biological reagents. The technological advances led to consider the diagnostic use of saliva for an array of analytes and DNA source. The purpose of the present study was to compare DNA from saliva with those from blood and buccal swab, to evaluate diagnostic and forensic application of saliva, to investigate the changes of genomic DNA in saliva according to the storage temperature and period of saliva samples, and to evaluate the integrity of the DNA from saliva stored under various storage conditions by PCR analysis. Peripheral venous blood, unstimulated whole saliva, stimulated whole saliva, and buccal swab were obtained from healthy 10 subjects (mean age: $29.9{\pm}9.8$ years) and genomic DNA was extracted using commercial kit. For the study of effects of various storage conditions on genomic DNA from saliva, stimulated whole saliva were obtained from healthy 20 subjects (mean age: $32.3{\pm}6.6$ years). After making aliquots from fresh saliva, they were stored at room temperature, $4^{\circ}C$, $-20^{\circ}C$, and $-70^{\circ}C$. Saliva samples after lyophilization and dry-out procedure were stored at room temperature. After 1, 3, and 5 months, the same experiment was performed to investigate the changes in genomic DNA in saliva samples. In case of saliva aliquots stored at room temperature and dry-out samples, the results in 2 weeks were also included. Integrity of DNA from saliva stored under various storage conditions was also evaluated by PCR amplification analysis of $\beta$-globin gene fragments (989-bp). The results were as follows: 1. Concentration of genomic DNA extracted from saliva was lower than that from blood (p<0.05), but there were no significant differences among various types of saliva samples. Purities of genomic DNA extracted from stimulated whole saliva and lyophilized one were significantly higher than that from blood (p<0.05). Purity of genomic DNA extracted from buccal swab was lower than those from various types of saliva samples (p<0.05). 2. Concentration of genomic DNA from saliva stored at room temperature showed gradual reduction after 1 month, and decreased significantly in 3 and 5 months (p<0.05, p<0.01, respectively). Purities of DNA from saliva stored for 3 and 5 months showed significant differences with those of fresh saliva and stored saliva for 1 month (p<0.05). 3. In the case of saliva stored at $4^{\circ}C$ and $-20^{\circ}C$, there were no significant changes of concentration of genomic DNA in 3 months. Concentration of DNA decreased significantly in 5 months (p<0.05). 4. There were no significant differences of concentration of genomic DNA from saliva stored at $-70^{\circ}C$ and from lyophilized one according to storage period. Concentration of DNA showed decreasing tendency in 5 months. 5. Concentration of genomic DNA immediately extracted from saliva dried on Petri dish were 60% compared with that of fresh saliva. Concentration of DNA from saliva stored at room temperature after dry-out showed rapid reduction within 2 weeks (p<0.05). 6. Amplification of $\beta$-globin gene using PCR was successful in all lyophilized saliva stored for 5 months. At the time of 1 month, $\beta$-globin gene was successfully amplified in all saliva samples stored at $-20^{\circ}C$ and $-70^{\circ}C$, and in some saliva samples stored at $4^{\circ}C$. $\beta$-globin gene was failed to amplify in saliva stored at room temperature and dry-out saliva.

• Journal of the Korean Wood Science and Technology
• /
• v.2 no.4
• /
• pp.4-14
• /
• 1974

The total forest land area in Korea accounts for some 67 percent of the nation's land total. Its productivity, however, is very low. Consequently, forest production accounts for only about 2 percent of the gross national product and a minor proportion of no more than about 5 percent versus primary industry. In this case, however, only the direct income from forestry is taken into account, making no reference to the forestry output induced by other industrial sectors. The value added Or the induced forestry output in manufacturing the primary wood products into higher quality products, makes a larger contribution to the economy than direct contribution. So, this author has tried to analyze the structure of forestry and compute the repercussion effect and the induced output of primary forest products when utilized by other industries for their raw materials, Hsing the input-output table and attached tables for 1963 and 1966 issued by the Bank of Korea. 1. Analysis of forestry structure A. Changes in total output Durng the nine-year period, 1961-1969, the real gross national product in Korea increased 2.1 times, while that of primary industries went up about 1. 4 times. Forestry which was valued at 9,380 million won in 1961, was picked up about 2. 1 times to 20, 120 million won in 1969. The rate of the forestry income in the GNP, accordingly, was no more than 1.5 percent both in 1961 and 1962, whereas its rate in primary industries increased 3.5 to 5.4 percent. Such increase in forestry income is attributable to increased forest production and rise in timber prices. The rate of forestry income, nonetheless, was on the decrease on a gradual basis. B. Changes in input coefficient The input coefficient which indicates the inputs of the forest products into other sectors were up in general in 1966 over 1963. It is noted that the input coefficient indicating the amount of forest products supplied to such industries closely related with forestry as lumber and plywood, and wood products and furniture, showed a downward trend for the period 1963-1966. On the other hand, the forest input into other sectors was generally on the increase. Meanwhile, the input coefficient representing the yolume of the forest products supplied to the forestry sector itself showed an upward tendency, which meant more and more decrease in input from other sectors. Generally speaking, in direct proportion to the higher input coefficient in any industrial sector, the reinput coefficient which denotes the use of its products by the same sector becomes higher and higher. C. Changes in ratio of intermediate input The intermediate input ratio showing the dependency on raw materials went up to 15.43 percent m 1966 from 11. 37 percent in 1963. The dependency of forestry on raw materials was no more than 15.43 percent, accounting for a high 83.57 percent of value added. If the intermediate input ratio increases in any given sector, the input coefficient which represents the fe-use of its products by the same sector becomes large. D. Changes in the ratio of intermediate demand The ratio of the intermediate demand represents the characteristics of the intermediary production in each industry, the intermediate demand ratio in forestry which accunted for 69.7 percent in 1963 went up to 75.2 percent in 1966. In other words, forestry is a remarkable industry in that there is characteristics of the intermediary production. E. Changes in import coefficient The import coefficient which denotes the relation between the production activities and imports, recorded at 4.4 percent in 1963, decreased to 2.4 percent in 1966. The ratio of import to total output is not so high. F. Changes in market composition of imported goods One of the major imported goods in the forestry sector is lumber. The import value increased by 60 percent to 667 million won in 1966 from 407 million won in 1963. The sales of imported forest products to two major outlets-lumber and plywood, and wood products and furniture-increased to 343 million won and 31 million won in 1966 from 240million won and 30 million won in 1963 respectively. On the other hand, imported goods valued at 66 million won were sold to the paper products sector in 1963; however, no supply to this sector was recorded in 1963. Besides these major markets, primary industries such as the fishery, coal and agriculture sectors purchase materials from forestry. 2. Analysis of repercussion effect on production The repercussion effect of final demand in any given sector upon the expansion of the production of other sectors was analyzed, using the inverse matrix coefficient tables attached to the the I.O. Table. A. Changes in intra-sector transaction value of inverse matrix coefficient. The intra-sector transaction value of an inverse matrix coefficient represents the extent of an induced increase in the production of self-support products of the same sector, when it is generated directly and indirectly by one unit of final demand in any given sector. The intra-sector transaction value of the forestry sector rose from 1.04 in 1963 to 1, 11 in 1966. It may well be said, therefore, that forestry induces much more self-supporting products in the production of one unit of final demand for forest products. B. Changes in column total of inverse matrix coefficient It should be noted that the column total indicates the degree of effect of the output of the corresponding and related sectors generated by one unit of final demand in each sector. No changes in the column total of the forestry sector were recorded between the 1963 and 1966 figures, both being the same 1. 19. C. Changes in difference between column total and intra-sector transaction amount. The difference between the column total and intra-sector transaction amount by sector reveals the extent of effect of output of related industrial sector induced indirectly by one unit of final demand in corresponding sector. This change in forestry dropped remarkable to 0.08 in 1966 from 0.15 in 1963. Accordingly, the effect of inducement of indirect output of other forestry-related sectors has decreased; this is a really natural phenomenon, as compared with an increasing input coefficient generated by the re-use of forest products by the forestry sector. 3. Induced output of forestry A. Forest products, wood in particular, are supplied to other industries as their raw materials, increasng their value added. In this connection the primary dependency rate on forestry for 1963 and 1966 was compared, i. e., an increase or decrease in each sector, from 7.71 percent in 1963 to 11.91 percent in 1966 in agriculture, 10.32 to 6.11 in fishery, 16.24 to 19.90 in mining, 0.76 to 0.70 in the manufacturing sector and 2.79 to 4.77 percent in the construction sector. Generally speaking, on the average the dependency on forestry during the period 1963-1966 increased from 5.92 percent to 8.03 percent. Accordingly, it may easily be known that the primary forestry output induced by primary and secondary industries increased from 16, 109 million won in 1963 to 48, 842 million won in 1966. B. The forest products are supplied to other industries as their raw materials. The products are processed further into higher quality products. thus indirectly increasing the value of the forest products. The ratio of the increased value added or the secondary dependency on forestry for 1963 and 1966 showed an increase or decrease, from 5.98 percent to 7.87 percent in agriculture, 9.06 to 5.74 in fishery, 13.56 to 15.81 in mining, 0.68 to 0.61 in the manufacturing sector and 2.71 to 4.54 in the construction sector. The average ratio in this connection increased from 4.69 percent to 5.60 percent. In the meantime, the secondary forestry output induced by primary and secondary industries rose from 12,779 million Wall in 1963 to 34,084 million won in 1966. C. The dependency of tertiary industries on forestry showed very minor ratios of 0.46 percent and 0.04 percent in 1963 and 1966 respectively. The forestry output induced by tertiary industry also decreased from 685 million won to 123 million won during the same period. D. Generally speaking, the ratio of dependency on forestry increased from 17.68 percent in 1963 to 24.28 percent in 1966 in primary industries, from 4.69 percent to 5.70 percent in secondary industries, while, as mentioned above, the ratio in the case of tertiary industry decreased from 0.46 to 0.04 percent during the period 1963-66. The mining industry reveals the heaviest rate of dependency on forestry with 29.80 percent in 1963 and 35.71 percent in 1966. As it result, the direct forestry income, valued at 8,172 million won in 1963, shot up to 22,724 million won in 1966. Its composition ratio lo the national income rose from 1.9 percent in 1963 to 2.3 per cent in 1966. If the induced outcome is taken into account, the total forestry production which was estimated at 37,744 million won in 1963 picked up to 105,773 million won in 1966, about 4.5 times its direct income. It is further noted that the ratio of the gross forestry product to the gross national product. rose significantly from 8.8 percent in 1963 to 10.7 percent in 1966. E. In computing the above mentioned ratio not taken into consideration were such intangible, indirect effects as the drought and flood prevention, check of soil run-off, watershed and land conservation, improvement of the people's recreational and emotional living, and maintenance and increase in the national health and sanitation. F. In conclusion, I would like to emphasize that the forestry sector exercices an important effect upon the national economy and that the effect of induced forestry output is greater than its direct income.

• Journal of the Korean Wood Science and Technology
• /
• v.15 no.2
• /
• pp.26-52
• /
• 1987

Among the diffuse-porous woods which arc dominant in Korea and used as construction materials due to their wood quality, ten species of six genus involving seven species of three genus in Betulaceae were studied on the radial variation of structural demenb. The species studied were Betula platyphylla var. japonica, B. ermanii, B. davurica, B. scstata, B. schmidtii, Carpinus laxifora, Alnus japonica, Prunus sargentii. Acer mono and Diospyros kaki. Wood fiber, vessel elements and ray increased rapidly in size from pith to a certain annual ring. After then the radial variation in size of the main structural elements seemed to be divided into three types; levelled off curve pattern indicating constant size(type I), continuously increasing curve pattern showing ever increase in size (type II) and parabolic curve pattern showing the gradual decrease after the maximum (type III), but the variation types by structural dements were different even in the same species. Based on the results from this study, it appears to be reasonable to consider the stabilized age of wood fiber, vessel elements and ray rather than considering wood fiber length in distinguishing mature woods from juvenile woods.