• The Journal of Korean Physical Therapy
• /
• v.21 no.1
• /
• pp.73-80
• /
• 2009

Purpose: In order to examine difference in the activity of potential of spinal neurons and cortical neurons according to muscle contraction type in post stroke hemiplegic subjects and healthy subjects, the present study conducted an experiment as follows. Methods: The subjects in the experimental group were 17 left-side hemiplegic subjects (9 female, 8 male; mean age, 63.41$\pm$9.86 years) with the right hand as the dominant hand selected among post stroke hemiplegic subjects, and 17 age matched healthy control subjects (10 female, 7 male; mean age, 64.12$\pm$12.07 years). Movement-related cortical potentials (MRCPs) were measured using surface electromyography and electroencephalography while concentric and eccentric movements were made alternately. Results: As to the pattern of the activity of MRCP, which indicates the activity of motor cortical neurons, we found that the amplitude is high (p<0.01), the length of excitement is short (p<0.01) and the ascending gradient of amplitude to the peak increases (p<0.05) in post stroke hemiplegic subjects' lesion sites different from healthy subjects. Conclusion: The activity of cortical neurons was no difference in activity according to contraction type was observed in post stroke hemiplegic subjects' lesion sites. This suggests that there is no distinction in the activity of cortical neurons between concentric contraction and eccentric contraction. Accordingly, if post stroke hemiplegic subjects' activity of motor cortex is analyzed by measuring MRCPs, it is considered useful in research on neural plasticity or as a ground of clinical effects in the area of physical therapy for the central nervous system.

• The Korean Journal of Ecology
• /
• v.27 no.1
• /
• pp.35-41
• /
• 2004

Phragmites australis is the dominant and constructive species among plant communities in the wetlands of the downstream of Yellow River, China. Its morphological characters were high variable in different habitats. Studies on Morphological and RAPD variation of 15 P. australis populations from this region showed that soil salinity was the dominant ecological factor that affected the morphological characters of P. australis. The basal diameter, height, leaf length, leaf width, internode length, internode accounts, panicle length were negatively related to salinity. 194 loci were amplified by RAPD, of which 9 loci was highly negative-related to salinity, and showed a tendency to prefer the habitats with fresh water. 4 loci were positively related to the salinity, and showed a tendency to prefer the salinized habitats. Most loci were neutral to salinity. The morphological and genetic characters of BZH were special, and the speciality should not be determined by salinity. The morphological characters were affected by genetic information and environment. The morphological characters should change gradually and continuously along environmental gradient under plasticity, but should changed continuously or not in genetic control. The relevancies among quantitive characters, ecological factors and genetic variation in natural populations still will still be a focus and difficulty of ecological genetics of P. australis in the future.

• Geomechanics and Engineering
• /
• v.36 no.3
• /
• pp.259-276
• /
• 2024

The undrained shear strength is widely acknowledged as a fundamental mechanical property of soil and is considered a critical engineering parameter. In recent years, researchers have employed various methodologies to evaluate the shear strength of soil under undrained conditions. These methods encompass both numerical analyses and empirical techniques, such as the cone penetration test (CPT), to gain insights into the properties and behavior of soil. However, several of these methods rely on correlation assumptions, which can lead to inconsistent accuracy and precision. The study involved the development of innovative methods using extreme gradient boosting (XGB) to predict the pile set-up component "A" based on two distinct data sets. The first data set includes average modified cone point bearing capacity (q_t), average wall friction (f_s), and effective vertical stress (σ_vo), while the second data set comprises plasticity index (PI), soil undrained shear cohesion (S_u), and the over consolidation ratio (OCR). These data sets were utilized to develop XGBoost-based methods for predicting the pile set-up component "A". To optimize the internal hyperparameters of the XGBoost model, four optimization algorithms were employed: Particle Swarm Optimization (PSO), Social Spider Optimization (SSO), Arithmetic Optimization Algorithm (AOA), and Sine Cosine Optimization Algorithm (SCOA). The results from the first data set indicate that the XGBoost model optimized using the Arithmetic Optimization Algorithm (XGB - AOA) achieved the highest accuracy, with R2 values of 0.9962 for the training part and 0.9807 for the testing part. The performance of the developed models was further evaluated using the RMSE, MAE, and VAF indices. The results revealed that the XGBoost model optimized using XGBoost - AOA outperformed other models in terms of accuracy, with RMSE, MAE, and VAF values of 0.0078, 0.0015, and 99.6189 for the training part and 0.0141, 0.0112, and 98.0394 for the testing part, respectively. These findings suggest that XGBoost - AOA is the most accurate model for predicting the pile set-up component.

• Transactions of Materials Processing
• /
• v.19 no.8
• /
• pp.494-501
• /
• 2010

The main objective of this study is to examine the sensitivity of calibration curves of FEA of ring compression test to frictional shear factor. Ring compression test has been investigated by measuring dimensional changes at different positions of ring specimen and they include the changes in internal diameter at the middle and top section of the specimen, outer diameter at the middle and top section, surface expansion at the top surface, respectively. Initial ring geometries employed in analysis maintain a fixed ratio of 6 : 3 : 2, i.e. outer diameter : inner diameter : thickness of the ring specimen, which is generally known as 'standard' specimen. A rigid plastic material for different work-hardening characteristics has been modeled for simulations using rigid-plastic finite element code. Analyses have been performed within a definite range of friction as well as over whole range of friction to show different sensitivities to the interfacial friction for different ranges of friction. The results of investigation in this study have been summarized in terms of a dimensionless gradient. It has been known from the results that the dimensional changes at different positions of ring specimen show different linearity and sensitivity to the frictional condition on the contact surface.

• Transactions of Materials Processing
• /
• v.13 no.1
• /
• pp.53-58
• /
• 2004

The microstructural changes of Al-Zn-Mg-Cu alloy containing Sc during hot extrusion and post heat treatment were investigated. Two kinds of Al-Sc alloys with different alloying elements (B1, B2) were hot extruded to make T-shape bars at extrusion temperature of $380^{\circ}C$, then the bars were solution treated at $480^{\circ}C$ for 2hrs followed by artificial aging at $120^{\circ}C$ for 24hrs. The interior microstructure of as extruded bar consisted of elongated grains, however, fine equiaxed grains were also observed around surface. The microstructural gradient suggested that different restoration process could proceed during the hot extrusion. For B1 and B2, different grain growth behaviors were found around the surface during the post heat treatment. Rapid grain growth behavior was observed for B1 around the surface, however, it was not observed for B2. Orientation pinning, which was related with the evolution of preferred orientation, and precipitation were thought to be responsible for the rapid grain growth.

• Transactions of Materials Processing
• /
• v.26 no.1
• /
• pp.35-40
• /
• 2017

Laser forming is an advanced process in sheet metal forming in which thermal stress originated from the laser heat source is used to shape the metal sheet. However, substantial waiting time is normally necessary for the workpiece to cool down between consecutive scans so that a steep temperature gradient can be reestablished in the next scan. In order to solve this drawback, laser bending characteristics are experimentally implemented in underwater condition. Laser forming effects under various conditions, including different laser power, scanning velocity, beam diameter, number of passes and material, are investigated. The results show that the underwater laser forming facilitates deliberate forming. The bending angle per respective laser scan is decreased with increasing the number of passes and scanning velocity.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.1 no.1 s.1
• /
• pp.117-125
• /
• 2001

This paper presented the analysis of stress regimes in and around inactive and active fault zones. The stress regime in the vicinity of an existing inactive fault zone is dependent on the orientation of the fault with respect to the current stress field and the contrast between the elastic properties of the faulted rock and those of the surrounding rock. In the analysis of stress regimes around an active fault zone, if the yielding stress is exceeded during loading, the localized shearing in a fault zone will result in weakness with mean stresses in the fault becoming lower than those in the surrounding rock. It can be expected that such stress gradients will induce fluid flow towards the faults zone.

• Transactions of Materials Processing
• /
• v.8 no.3
• /
• pp.301-301
• /
• 1999

Austenitic stainless steels such as AISI 316L have been used in equipment in which fluid flows at high speeds which can induce cavitation erosion on metallic surfaces due to the collapse of cavities, where the collapse is caused by the sudden change of local pressure within the liquid. Usually AISI 316L is susceptible to cavitation erosion. This research focuses on developing a better material to replace the AISI 316L used in equipment with high speed fluid flow, such as impellers. The effects of Rare Earth Metal (REM) additions on the cavitation erosion-corrosion resistance of duplex stainless steels were studied using metallographic examination, the potentiodynamic anodic polarization test, the tensile test, the X-ray diffraction test and the ultrasonic cavitation erosion test. The experimental alloys were found to have superior mechanical properties due to interstitial solid solution strengthening, by adding high nitrogen (0,4%), as well as by the refinement of phases and grains induced by fine REM oxides and oxy-sulfides. Corrosion resistance decreases in a gentle gradient as the REM content increases. However, REM containing alloys show superior corrosion resistance compared with that of other commercial alloys (SAF 2507, AISI 316L). Owing to their excellent mechanical properties and corrosion resistance, the alloys containing REM have high cavitation erosion-corrosion resistance.

• Transactions of Materials Processing
• /
• v.23 no.5
• /
• pp.317-322
• /
• 2014

Bursting during tube hydroforming is preceded by localized necking. The retardation of the initiation of necking is a means to enhance hydroformability. Since high strain gradients occur at the necking sites, a decrease in local strain gradients is an effective way to retard the initiation of necking. In the current study, the expansion at potential necking sites was intentionally restricted in order to reduce the strain gradient at potential necking sites. From the strain distribution obtained from FEM, it is possible to determine strain concentrated zones, which are the potential necking sites. Prior to the hydroforming of a trailing arm, an incompressible material(such as lead) is attached to the tube where the strain-concentrated zone would contact the die. Due to the incompressibility of lead, the tube expansion is locally restricted, and the resultant strain extends to adjacent regions of the tube during hydroforming. After the first stage of hydroforming, the lead is removed from the tube, and the hydroforming continues to the final targeted shape without any local restriction. This method was successfully used to fabricate a complex shaped automotive trailing arm that had previously failed during traditional hydroforming fabrication.

• Transactions of Materials Processing
• /
• v.31 no.3
• /
• pp.136-142
• /
• 2022

The purpose of this study was to investigate the effects of sample thickness and support structure on the residual stress of Hastelloy X superalloy samples fabricated by laser powder bed fusion (LPBF), which is an additive manufacturing process. The residual stresses of LPBF samples with different thicknesses and support structures were measured using X-ray diffraction. The results revealed that as the thickness of sample increased from 2.5 mm to 20 mm, its tensile residual stress gradually decreased from 443.5 MPa to 182.2 MPa. Additionally, the residual stress in the bottom region of sample was higher than that in the top region, and the residual stress difference in the bottom and top regions became more pronounced as the sample thickness decreased. The residual stress of LPBF sample also varied depending on the structure of support. The residual stress of sample decreased with increasing contract area between the sample and the support, because the larger contract area led to smaller temperature gradient throughout the sample.