• Journal of the Korean Geotechnical Society
• /
• v.30 no.12
• /
• pp.41-49
• /
• 2014

The 3D numerical analysis is carried out to investigate the settlement behavior of flexible mat foundations subjected to vertical loads. Special attention is given to the improved analytical method (YS-MAT) that reflects the mat flexibility and soil spring coupling effect. The soil model captures the stiffness of the soil springs as well as the shear interaction between the soil springs. The proposed method has been validated by comparing the results with other numerical methods and a field measurement on mat foundation. Through comparative studies, the settlement of the proposed method was in relatively good agreement with those of a field measurement and other numerical methods. The results permit us to estimate the response of the mat foundation subjected to vertical loads that should be taken into account in the combination of mat flexibility and soil continuity characteristics.

• Journal of the Korean Geotechnical Society
• /
• v.29 no.1
• /
• pp.161-170
• /
• 2013

In this paper, numerical pile segment analysis is conducted with an advanced soil elastoplastic model to investigate the diameter effects on skin friction behaviour of a drilled shaft in sand. Ultimate skin friction and 't-z' behavior from the pile segment analyses for drilled shafts show good agreement with those from design methods. Higher ultimate skin friction for the smaller diameter pile is related to the greater increase in the effective radial stress at the interface due to the localized dilation at and near the pile interface. Stiffer t-z curve for the smaller diameter pile is related to the early occurrence of three shear stages (early, dilation, constant volume shear stages). The diameter effects on ultimate skin friction of drilled shafts are more prominent for denser sand and lower confining pressure.

• Structural Engineering and Mechanics
• /
• v.72 no.6
• /
• pp.675-687
• /
• 2019

As the bridges are an integral part of the transportation network, their function as one of the most important vital arteries during an earthquake is fundamental. In a design point of view, the bridges piers, and in particular the wall piers, are considered as effective structural elements in the seismic response of bridge structures due to their cantilever performance. Owing to reduced seismic load during design procedure, the response of these structural components should be ductile. This ductile behavior has a direct and decisive correlation to the development of plastic hinge region at the base of the wall pier. Several international seismic design codes and guidelines have suggested special detailing to assure ductile response in this region. In this paper, the parameters which affect the length of plastic hinge region in the reinforced concrete bridge with wall piers were examined and the sensitivity of these parameters was evaluated on the length of the plastic hinge region. Sensitivity analysis was accomplished by independently variable parameters with one standard deviation away from their means. For this aim, the Monte Carlo simulation, tornado diagram analysis, and first order second moment method were used to determine the uncertainties associated with analysis parameters. The results showed that, among the considered design variables, the aspect ratio of the pier wall (length to width ratio) and axial load level were the most important design parameters in the plastic hinge region, while the yield strength of transverse reinforcements had the least effect on determining the length of this region.

• Journal of the Korean Geotechnical Society
• /
• v.28 no.4
• /
• pp.115-124
• /
• 2012

The responses of stone column-improved ground under seismic loading are investigated using a series of 1g shaking table tests. These tests show similar results to those of one dimensional numerical models for stone column-improved ground based on Baez's assumption on the soil and stone-column interaction. The experimental and numerical results show that the stone column can prevent large shear deformations incurred due to cyclic softening in clayey deposits, but they also show that the surface acceleration in the improved clayey deposits may amplify more than that in unimproved clayey deposits when subjected to short periodic seismic motions.

• Journal of the Korean Geotechnical Society
• /
• v.27 no.12
• /
• pp.85-96
• /
• 2011

A breakwater is a important structure for both calmness of harbor and protection of the port facilities from waves generated from typhoons or wind. This study adopted the rubble mound breakwater, which is one of the most popular type of breakwaters in Korea. Rubble mound breakwater had been designed by considering only static condition previously. Recently, a dynamic wave-load due to waves has been also considered in designing breakwater. In design, the wave-load is assumed as an uniform load which only acts in the front slope of the breakwater. However, the assumption is not applicable in reality. In this study, therefore, a real-time wave-load acting on the breakwater instead of the uniform load is considered, and it is assumed to be acting on the seabed too. Based on the numerical analysis, it is found that there is a significant difference in the maximum settlement compared with the result predicted by the existing design method.

• Journal of the Korean Geotechnical Society
• /
• v.33 no.10
• /
• pp.59-69
• /
• 2017

The tension load of the ground anchor inserted in the ground gradually changes over time. In this regard the change of the initial tension load is primarily decreased by the fixation condition of the fixing head and the mechanical characteristics of the tensile material. The subsequent additional tension load is a time-dependent loss mostly due to the fixing conditions of the bonded length and the surrounding ground properties of the field. In this paper, therefore, a measurement system using a relative displacement detector that can relatively easily measure the change of tension load is discussed. As a result of the review, it was confirmed that the results using the relative displacement detector are similar to those of the real scale model test, and it was also confirmed that similar results were obtained with the result of the pull-out test conducted on the ground anchors fixed to weathered rocks condition. In addition, a pull-out test was conducted on the test anchors whose initial tension load loss was relatively large and through this test pull-out behavior of the tension type ground anchors was verified.

• Journal of the Korean Geotechnical Society
• /
• v.34 no.7
• /
• pp.29-38
• /
• 2018

Three-dimensional continuum modeling of dynamic soil-pile-structure interaction embedded in a liquefiable sand was carried out. Finn model which can model liquefaction behavior using effective stress method was adopted to simulate development of pore water pressure according to shear deformation of soil directly in real time. Finn model was incorporated into Non-linear elastic, Mohr-Coulomb plastic model. Calibration of proposed modeling method was performed by comparing the results with those of the centrifuge tests performed by Wilson (1998). Excess pore pressure ratio, pile bending moment, pile head displacement-time history according to depth calculated by numerical analysis agreed reasonably well with the test results. Validation of the proposed modeling method was later performed using another test case, and good agreement between the computed and measured values was observed.

• Geotechnical Engineering
• /
• v.5 no.4
• /
• pp.37-46
• /
• 1989

The object of this paper is to study the general characteristics of overconsolidated silty clays subjected to repeated loading. The samples are first remolded. overconsolidated and a series of strain - controlled triaxial repeated tests are carried out. Generally the relationship of deviator stress - axial strain of overconsolidated clay is similar in pattern to the normally consolidated clay under single load. But the behavior of the pore water pressure build up in the sample subjected to repeated loading is dependent upon the consolidation history and the level of repeated stress. Therefore through the series of the tests, the characteristics of stress -strain relationship of soils which are differentlly overconsolidated are investigated, analysed and then compared with each soils. And also, from the relationship of test results, the strength and strain characteristics of soils are obierved. The equilibrium lines which presents the critical repeated stress and equilibrium state in the sample under repeated loading, are often straight, but may be curved. And the tendency of the equilibrium lines is observed as to the variation of overconsolidation ratio.

• Journal of the Korean Geotechnical Society
• /
• v.18 no.3
• /
• pp.33-41
• /
• 2002

Soil nailing type of retaining structures has been widely used in Korea far the purpose of the temporary and permanent support in excavations and slope stability. The important factors in application of soil nailing systems in urban excavation site nearby the existing structures are the displacement of the wall and tensile farce of the nails, etc. In this paper, the fled back analyses are carried out at 11 excavation sites to investigate the behavior of tensile farce of nails at stepwise excavation in the multi-layered strata including various rock layers. The results of the fled back analysis are less than about 50% of the measured ones. The distance of active zone by measurements are shown almost larger than that of fled back analysis when the distance of active Bone is defined from the surface of wall to the potential failure surface. And the results of fled back analysis are within the range proposed by the project CLOUTERRE and Cartier & Gigan (1983) which were 0.3$H_f$, and 0.5$H_f$, of the final excavation depth ($H_f$,) respectively, but the values of the measurement were larger than these values.

• Journal of the Korean Geotechnical Society
• /
• v.18 no.3
• /
• pp.43-50
• /
• 2002

This paper describes a simplified numerical procedure for analyzing the response of bridge pier foundations due to riverbed scouring. A computationally efficient algorithm to analyze the behavior of a pile group is proposed by considering soil-pile, pile-cap, and pile-fluid interactions. The complex phenomenon of the pile-soil interaction is modeled by discrete nonlinear soil springs (p-y, t-z and q-z curves). The pile-cap interaction is considered by geometric configuration of the piles in a group and connectivity conditions between piles and the cap. The pile-fluid interaction is incorporated into the procedure by reducing the stiffness of the soil-pile reactions as a result of nonlinearity and degradation of the soil stiffness with river bridge scouring. Through the numerical study, it is shown that the maximum bending moment increases with increasing scour depth. Thus it is desirable to check the stability elf pile groups based on soil-pile and pile-cap interactions by considering scouring depth in the riverbed.