• 한국가스학회지
• /
• 제13권1호
• /
• pp.9-13
• /
• 2009

가스히터의 가동으로 인하여 발생하는 소음 및 진동의 주 원인은 연소음(combustion roar)과 연소진동음(combustion oscillation)이다. 연소음(combustion roar)의 특징은 음압이 넓은 주파수대에 걸쳐 있고, 크기도 비교적 일정 하다. 반면 연소진동음(combustion oscillation)은 연소실내 기체의 고유진동수에 대하여 버너계가 Positive Feedback을 일으켜 공진할 때 발생되는 소음 및 진동이다. 따라서 소음 및 진동을 해결 할 수 있는 방법은, 공진을 피하는 것이다. 첫 번째, 버너에서 연료와 공기량의 비율을 조절하여 진동수를 변화시키거나, 연소실내에서의 연료와 공기의 혼합속도를 변화시키는 방법이 있다. 두 번째, 연소실의 길이나 이코노마이저(Economizer)의 형상을 바꾸어 고유진동수를 변경시키는 방법이 있다. 본 논문에서는 이코노마이저(Economizer)를 변경하여 공명을 회피하였다.

• 대한안전경영과학회지
• /
• 제17권2호
• /
• pp.229-234
• /
• 2015

Depending on the living styles, the types of energy consumed by households have changed, and the consumption has increased rapidly. Consequently, those have led to environmental issues, such as exhaustion of energy and the climate changes. As one of solutions to such issues, energy efficiency can be approached. Therefore, in this study, the gas water heater(115S type Rheem products) that made in Germany and obtain hot water using gas as a heat source is selected. a $1.0m^3$ water tank with a 6kW electronic heater is installed and a water temperature and pressure is maintain constantly also thermometer is injected. Two of gas meter, one of pressure regulator and three of time measurement devices are installed in a combustion facility and fuelling facility with a magnet valve so it can observe and record combustion reactions. Quantity of hot water that heated by boiler is recorded using a quantity measurement tank, and have been heated by the boiler have been to record and measure the amount and utilized the data acquired through measurement of all factors that are applied to acquire hot water in order to calculate the use rate of final energy. In conclusion, this researcher drew the economic strong points of the hot water generated by gas.

• Transactions on Electrical and Electronic Materials
• /
• 제13권1호
• /
• pp.27-30
• /
• 2012

This paper proposes a micro gas sensor for measuring $H_2S$ gas. This is based on a $SnO_2$-CuO multi-layer thin film. The sensor has a silicon diaphragm, micro heater, and sensing layers. The micro heater is embedded in the sensing layer in order to increase the temperature to an operating temperature. The $SnO_2$-CuO multi layer film is prepared by the alternating deposition method and thermal oxidation which uses an electron beam evaporator and a thermal furnace. To determine the effect of the number of layers, five sets of films are prepared, each with different number of layers. The sensitivities are measured by applying $H_2S$ gas. It has a concentration of 1 ppm at an operating temperature of $270^{\circ}C$. At the same total thickness, the sensitivity of the sensor with multi sensing layers was improved, compared to the sensor with one sensing layer. The sensitivity of the sensor with five layers to 1 ppm of $H_2S$ gas is approximately 68%. This is approximately 12% more than that of a sensor with one-layer.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2006년 제4회 한국유체공학학술대회 논문집
• /
• pp.313-316
• /
• 2006

As Decentralized Generation(DG) becomes more reliable and economically feasible, it is expected that a higher application of DG units would be interconnected to the existing grids. This new market penetration of DG technologies is linked to a large number of factors like technologies costs and performances, interconnection issues, safety, market regulations, environmental issues or grid connection constrains. Korea Electric Power Corporation (KEPCO) has researched performance characteristics of the 60k W class 1) basic start-up & shutdown operation analysis 2) interconnection test 3) MGT -absorption chiller-heater system in the local condition. Variations of heat recovery from exhaust gas has measured according to micro gas turbine output of 15, 30, 45, 60kW. From those results, the performance of the MGT-absorption chiller/heater system has been evaluated. The suggested strategy and experience for the evaluation of the distributed generation will be used for the introduction of other distributed generation technologies into the grid in the future.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 제5회 압연심포지엄 신 시장 개척을 위한 압연기술
• /
• pp.119-125
• /
• 2004

Radiant tube heaters are widely used for indirect heating in heat treatment processes such as continuous annealing line(CAL) or continuous galvanizing line(CGL). Main issues for radiant tube are temperature uniformity, lifetime, thermal efficiency. To achieve higher heat release, the radiant tubes are fired at a higher fuel rate and therefore local overheating occur. A numerical simulation based on a commercial code FLUENT has been performed to investigate local overheating of radiant tube heaters. To minimize local overheating, the effects of radiating fins, flue gas recirculation(FGR), two-stage combustion were investigated. More uniform temperature distribution was achieved in the longitudinal direction within the tube with radiating fins and this contributed to increase the life of radiant tubes. Furthermore, the radiant tube with radiating fins was proven to be more efficient than the one without fins. The effects of flue gas recirculation and two stage combustion on the efficiency of the radiant tube were also considered and the results were presented.

• 한국가스학회:학술대회논문집
• /
• 한국가스학회 1999년도 추계학술발표회 논문집
• /
• pp.175-178
• /
• 1999

• 한국가스학회:학술대회논문집
• /
• 한국가스학회 2005년도 추계학술발표회 논문집
• /
• pp.98-103
• /
• 2005

• 한국수소및신에너지학회논문집
• /
• 제27권4호
• /
• pp.431-440
• /
• 2016

Electric or hydrogen energy source is expected to solve a various issues including energy security and exhaust pollution. However, it is required a lot of time and a variety of development to apply for commercialization. Therefore, it is needed to translation fuels between the future and the present. DME (Dimethyl Ether) can play a reduce exhaust emission from medium- to heavy-duty engines that are mostly used in commercial sector. It have applied to the DME fuel as a various alternative fuel including power generation in many countries. Especially, it is necessary to secure the energy of energy-poor areas that are widely distributed around the world. And Korea also has the energy-poor areas due to geographical characteristics. These areas has been covered by their own energy through some small diesel generators, diesel boiler etc. If DME fuels are supplied in new demand such as rural sector with energy poor area, DME fuel will be available in the wider sector. In this study, it investigated performance and emission characteristics of agricultural generator and air heater using DME fuel. So the existing equipment of generator and air heater was modified to apply DME fuel. And combustion characteristics and properties of exhaust gas according to the contents of the DME fuel were evaluated. DME fuel showed a potential application in agricultural generator and air heater.

• 대한기계학회논문집 C: 기술과 교육
• /
• 제3권1호
• /
• pp.45-53
• /
• 2015

해양플랜트에서 생산된 석유 또는 가스를 파이프라인을 통해 운반하는 경우, 가스 하이드레이트나 왁스와 같은 고형물이 쉽게 발생하고 이를 방지하기 위한 유동 안정성을 확보하는 것이 매우 중요하다. 해양플랜트 파이프라인에서 생성된 가스 하이드레이트 또는 왁스를 제거 또는 방지하기 위해 최근 파이프라인 외벽에 히터를 감아 전기적으로 가열하는 방법이 채택되고 있다. 본 연구에서는 파이프라인을 가열하는 기존의 외부 가열형 방식에 비해, 새로운 형식의 내부 스월형 히터를 고안, 설계 및 제작하여 파이프라인 내에 설치하여 유동 안정성을 실험적으로 평가하였다. 고안된 내부 스월형 히터와 기존의 외부 가열형 히터의 파이프라인 출구 단면에서의 온도 분포와 열적 혼합 등의 열 및 유동 성능 평가 결과, 내부 스월형 히터가 외부 가열형 히터에 비해 열적 성능이 보다 우수한 것으로 확인되었다.

• 한국산학기술학회:학술대회논문집
• /
• 한국산학기술학회 2006년도 춘계학술발표논문집
• /
• pp.223-226
• /
• 2006

The micro-gas sensor based on carbon nanotubes (CNTs) was fabricated and its gas sensing characteristics on nitrogen dioxide ($NO_2$) have been investigated. The sensor consists of a heater, an insulating layer, a pair of contact electrodes, and CNT-sensing film on a micromachined diaphragm. The heater plays a role in the temperature change to modify sensor operation. Gas sensor responses of CNT-film to $NO_2$ at room temperature are reported. The sensor exhibits a reversible response with a time constant of a few minutes at thermal treatment temperature of $130^{\circ}C$.