• International Journal of Highway Engineering
• /
• v.17 no.4
• /
• pp.41-51
• /
• 2015

PURPOSES: This study investigates the mechanical performance of carbon-capturing concrete that mainly contains blast furnace slag. METHODS: The mixture variables were considered; these included Portland cement content, which was varied from 10% to 40% of the blast furnace slag by weight. The specimens were exposed to different conditions such as high $N_2$ and $O_2$ concentrations, laboratory conditions and high $CO_2$ conditions. Mechanical performances, including compressive and flexural strengths and carbon-capturing depth, were evaluated. RESULTS : The slump, air content and unit weight were not affected significantly by the variation in cement content. The strength development when the specimens were exposed to high purity air was slightly greater than that when exposed to high $CO_2$. As the cement content increased the compressive and flexural strength increased but not considerably. The carbon-capturing capacity decreased as the cement content increased. The specimens exposed in the field for 70 days had flexural strength greater than 3 MPa. CONCLUSIONS : The results indicate that cement content is not an important parameter in the development of compressive and flexural strengths. However, the carbon-capturing depth was higher for less cement content. Even after field exposure for 70 days, neither any significant damage on the surface nor any decrease in strength was observed.

• Journal of the Korean Applied Science and Technology
• /
• v.32 no.2
• /
• pp.188-193
• /
• 2015

Blast Furnace Slag is good for enhancing the qualities of concrete such as reducing hydration heat increasing fluidity, long-term strength and durability, but it has some problems: construction time is increased or the rotation rate of form is decreased due to low development of early strength. In this study, an aqueous alkali solution for alkali activated reaction was obtained by the electrolysis using concentrated water discharged from seawater desalination process. Prepared aqueous alkali solution was applied to produce mortars using blast furnace slag. The results can be summarized as follows : For the mortar, compressive strength was decreased below 2% of NaOH and increased below 6% of NaOH. And compressive strength was increased gradually with increasing NaOCl contents. However, NaCl contents of mortars caused a decrease of 28days strength above early strength.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.208.2-208.2
• /
• 2015

최근 산화물 반도체에 대한 연구가 활발하게 이루어지고 있다. 비정질 산화물 반도체인 In-Ga-Zn-O(IGZO)는 기존의 비정질 실리콘에 비해 공정 단가가 낮으며 넓은 밴드 갭으로 인한 투명성을 가지고 있고, 저온 공정이 가능하여 다양한 기판에 적용이 가능하다. 반도체의 공정 과정에서 열처리는 소자의 특성 개선을 위해 필요하다. 일반적인 열처리 방법으로 furnace 열처리 방식이 주로 이용된다. 그러나 furnace 열처리는 시간이 오래 걸리며 일반적으로 고온에서 이루어지기 때문에 최근 연구되고 있는 유리나 플라스틱, 종이 기판을 이용한 소자의 경우 기판이 손상을 받는 단점이 있다. 이러한 단점들을 극복하기 위하여 저온 공정인 마이크로웨이브를 이용한 열처리 방식이 제안되었다. 마이크로웨이브 열처리 기술은 소자에 에너지를 직접적으로 전달하기 때문에 기존의 다른 열처리 방식들과 비교하여 에너지 전달 효율이 높다. 또한 짧은 공정 시간으로 공정 단가를 절감하고 대량생산이 가능한 장점을 가지고 있으며, 저온의 열처리로 기판의 손상이 없기 때문에 기판의 종류에 국한되지 않은 공정이 가능할 수 있을 것으로 기대된다. 따라서 본 연구에서는 마이크로웨이브 열처리가 소자의 전기적 특성 개선에 미치는 영향을 확인하였다. 제작된 IGZO 박막 트렌지스터는 p-type bulk silicon 위에 thermal SiO2 산화막이 100 nm 형성된 기판을 사용하였다. RCA 클리닝을 진행한 후 RF sputter를 사용하여 In-Ga-Zn-O (1:1:1) 을 70 nm 증착하였다. 이후에 Photo-lithography 공정을 통하여 active 영역을 형성하였고, 전기적 특성 평가가 용이한 junctionless 트랜지스터 구조로 제작하였다. 후속 열처리 방식으로 마이크로웨이브 열처리를 1000 W에서 2분간 실시하였다. 그리고 기존 열처리 방식과의 비교를 위해 furnace를 이용하여 N2 가스 분위기에서 $600^{\circ}C$의 온도로 30분 동안 열처리를 실시하였다. 그 결과, 마이크로웨이브 열처리를 한 소자의 경우 기존의 furnace 열처리 소자와 비교하여 우수한 전기적 특성을 나타내는 것을 확인하였다. 따라서 마이크로웨이브를 이용한 열처리 공정은 향후 저온 공정을 요구하는 소자 공정에 활용될 수 있을 것으로 기대된다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.210.1-210.1
• /
• 2015

최근 산화물 반도체에 대한 연구가 활발하게 이루어지고 있다. 비정질 산화물 반도체인 In-Ga-Zn-O (IGZO)는 기존의 비정질 실리콘에 비해 공정 단가가 낮으며 넓은 밴드 갭으로 인한 투명성을 가지고 있고, 저온 공정이 가능하여 다양한 기판에 적용이 가능하다. 반도체의 공정 과정에서 열처리는 소자의 특성 개선을 위해 필요하다. 일반적인 열처리 방법으로 furnace 열처리 방식이 주로 이용된다. 그러나 furnace 열처리는 시간이 오래 걸리며 일반적으로 고온에서 이루어지기 때문에 최근 연구되고 있는 유리나 플라스틱, 종이 기판을 이용한 소자의 경우 기판이 손상을 받는 단점이 있다. 이러한 단점들을 극복하기 위하여 저온 공정인 마이크로웨이브를 이용한 열처리 방식이 제안되었다. 마이크로웨이브 열처리 기술은 소자에 에너지를 직접적으로 전달하기 때문에 기존의 다른 열처리 방식들과 비교하여 에너지 전달 효율이 높다. 또한 짧은 공정 시간으로 공정 단가를 절감하고 대량생산이 가능한 장점을 가지고 있으며, 저온의 열처리로 기판의 손상이 없기 때문에 기판의 종류에 국한되지 않은 공정이 가능할 수 있을 것으로 기대된다. 따라서 본 연구에서는 마이크로웨이브 열처리가 소자의 전기적 특성 개선에 미치는 영향을 확인하였다. 제작된 IGZO 박막트렌지스터는 p-type bulk silicon 위에 thermal SiO2 산화막이 100 nm 형성된 기판을 사용하였다. RCA 클리닝을 진행한 후 RF sputter를 사용하여 In-Ga-Zn-O (1:1:1)을 70 nm 증착하였다. 이후에 Photo-lithography 공정을 통하여 active 영역을 형성하였고, 전기적 특성 평가가 용이한 junctionless 트랜지스터 구조로 제작하였다. 후속 열처리 방식으로 마이크로웨이브 열처리를 1000 W에서 2분간 실시하였다. 그리고 기존 열처리 방식과의 비교를 위해 furnace를 이용하여 N2 가스 분위기에서 $600^{\circ}C$의 온도로 30분 동안 열처리를 실시하였다. 그 결과, 마이크로웨이브 열처리를 한 소자의 경우 기존의 furnace 열처리 소자와 비교하여 우수한 전기적 특성을 나타내는 것을 확인하였다. 따라서, 마이크로웨이브를 이용한 열처리 공정은 향후 저온 공정을 요구하는 소자 공정에 활용될 수 있을 것으로 기대된다.

• Journal of the Institute of Electronics Engineers of Korea TE
• /
• v.39 no.1
• /
• pp.31-36
• /
• 2002

Low energy boron ions were implanted into the preamorphized and crystalline silicon substrates to form 0.2${\mu}m$ $p^+-n$ junctions. The rapid thermal annealing(RTA) was used to annihilate the crystal defects due to implantation and to activate the implanted boron ions, and the furnace annealing was employed to reflow the BPSG(bolo-phosphosilicate glass). The implantation conditions for Gepreamorphization were the energy of 45keV and the dose of 3$\times$1014cm-2. BF2 ions employed as a p-type dopant were implanted with the energy of 20keV and the dose of 2$\times$1015cm-2. The thermal conditions of RTA and furnace annealing were $1000^{\circ}C$/10sec and $850^{\circ}C$/40min, respectively. The junction depths were measured by SIMS and ASR techniques, and the 4-point probe was used to measure the sheet resistances. The electrical characteristics were analyzed via the leakage currents of the fabricated diodes. The single thermal processing with RTA produced shallow junctions of good qualities, and the thermal treatment sequence of furnace anneal and RTA yielded better junction characteristics than that of RTA and furnace anneal.

• Analytical Science and Technology
• /
• v.12 no.2
• /
• pp.130-135
• /
• 1999

A graphite furnace atomic absorption spectrometry (GFAAS) with matrix modification has been used to determine trace amounts of arsenic, lead and selenium in rice flour samples. A mixed solution of palladium and magnesium nitrate was used as a matrix modifier to convert the analyte elements into a phase of higher thermostability and to increase the volatility of concomitants in graphite furnace. Matrix modification effects by the mixed solution were investigated for several elements (As, Cd, Cu, Pb, Se, Zn). It has been found that the matrix modifier substantially increase the pyrolysis and atomization temperature, and absorbance for As, Pb and Se. The concentration of As, Pb and Se in rice flour samples were determined by standard addition method with Zeeman background correction after microwave acid digestion. In this method the characteristic concentrations of As, Pb and Se are 26 ng/g, 18 ng/g, 24 ng/g on the basis of dry sample respectively.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.10a
• /
• pp.27.1-27.1
• /
• 2011

The recent extensive research of one-dimensional (1D) nanostructures such as nanowires (NWs) and nanotubes (NTs) has been the driving force to fabricate new kinds of nanoscale devices in electronics, optics and bioengineering. We attempt to produce silicon oxide nanowires (SiOxNWs) in a simple way without complicate deposition process, gaseous Si containing precursors, or starting material of $SiO_2$. Nickel (Ni) nanoparticles (NPs) were applied on Si wafer and thermally treated in a furnace. The temperature in the furnace was kept in the ranges between 900 and $1,100^{\circ}C$ and a mixture of nitrogen ($N_2$) and hydrogen ($H_2$) flowed through the furnace. The SiOxNWs had widths ranging from 100 to 200 nm with length extending up to ~10 ${\mu}m$ and their structure was amorphous. Ni NPs were acted as catalysts. Since there were no other Si materials introduced into the furnace, the Si wafer was the only Si sources for the growth of SiOxNWs. When the Si wafer with deposition of Ni NPs was heated, the liquid Ni-Si alloy droplets were formed. The droplets as the nucleation sites induce an initiation of the growth of SiOxNWs and absorb oxygen easily. As the droplets became supersaturated, the SiOxNWs were grown, by the reaction between Si and O and continuously dissolving Si and O onto NPs. Photoluminescence (PL) showed that blue emission spectrum was centered at the wavelength of 450 nm (2.76 eV). The details of growth mechanism of SiOxNWs and the effect of Ni NPs on the formation of SiOxNWs will be presented.

• Resources Recycling
• /
• v.20 no.3
• /
• pp.40-47
• /
• 2011

In this study, we investigated the strength, shrinkage and durability of alkali-activated mortar using blast furnace slag only, and admixed with blast-furnace slag and fly ash as cementious materials in oder to develop cementless alkali-activated concrete. In order to compare with the alkali-activated mortar, the normal mortar using ordinary portland cement was also test. In view of the results, we found out that strength development, the resistance to shrinkage and freezing-thawing of the cementless alkali-activated mortar have better than the mortar using ordinary portland cement. Especially, using the combined with blast furnace slag and fly ash develop high strength of above 60 MPa, reduce shrinkage of about 40% and improve freezing-thawing durability of approximately 20%, but promote the velocity of carbonation of 2~3 times.

• Journal of Environmental Health Sciences
• /
• v.35 no.5
• /
• pp.411-416
• /
• 2009

This study was initiated to improve the cooling water quality by chemical coagulation and sedimentation in steel mills. Due to the inefficient flocculation in the settling tanks of blast furnace cooling water systems, the solid particles in the cooling water overflow accumulate and clog the cooling system. To protect the cooling water system from such fouling, proper flocculants must be continuously used. Laboratory tests were performed for the indirect cooling water system of a plate mill. The batch test in the gas scrubbing cooling water system of a blast furnace showed that the proposed coagulant was more effective for the improvement of coagulation and sedimentation than the existing one. During the tests, cationic flocculants were more effective than use of only an anionic flocculant. The suggested combination of anionic and cationic flocculants can probably improve the turbidity removal efficiency of the cooling water. Proper control of the overflow rate by the designed residence time would help turbidity removal efficiency in the settling tank. In addition, the settling can be enhanced by adopting rapid and slow mixing alternatively. Scale problems in blast furnace cooling water system were reduced to some extent by efficient settling.

• Journal of computational fluids engineering
• /
• v.17 no.4
• /
• pp.16-23
• /
• 2012

Current display manufacturing processes apply thermal treatment of glass backplanes widely for hydrogen degassing, crystallization of thin-films, tempering, forming, and precompaction. Estimation of the characteristics of transient heating stages and thermal non-uniformities on a single glass substrate or in a stack of glasses are extremely helpful to understand non-homogeneity of mechanical and electronic features of nano/micro structures of end products. Based on simple heat transfer models and using an electric muffle furnace, temperature variations in a glass stack were predicted and measured for glass backplanes of $1.5{\times}1.85m^2$ in size and 0.7 mm in thickness. Except for the period of putting glass backplanes into the furnace, thermal radiation was the major heating mechanism for the treatment and theoretical predictions agreed well to the experimental temperatures on the backplanes. Using the theoretical model, thermal fields for a glass stack of glass-size, $2.2{\times}2.5m^2$, and of the number of sheets, 1 to 12, were calculated for practical design and manufacturing of the muffle furnace for large-scale displays, e.g. up to $8^{th}$ generation.