• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2009.05b
• /
• pp.97-100
• /
• 2009

This study is a basic experiment to complement the problems in decrease of strength in case we change lots of fly ash("FA" here in after) in ordinary portland cement("OPC" here in after). Mixing plaster that is known to be effective in improvement in hydration of blast furnace slag powder("BS" here in after). After FA changed concrete is mixed, the study physical proporties such as compression strength, increased proportionaly. When second-class BS 5 % and gypsum 2 % changed, compare to OPC strength approximately 120 % was recorded after one day. In FA 20 % case, according to the ratio of gypsum changed results showed similar trend, but compared to FA 10 % changed concrete, expression strength improvement was lower.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2017.11a
• /
• pp.81-82
• /
• 2017

This study analyzed the compressive and flexural strength characteristics and the permeability coefficient of the trial product of amorphous metallic fiber reinforced porous block using high volume blast furnace slag powder.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2017.11a
• /
• pp.161-162
• /
• 2017

As the use of cement increases with the development of modern society along with the increase of buildings, environmental pollution intensifies and researches on industrial byproducts are continuing. Research on blast furnace slag and fly ash as industrial byproducts is increasing, and research on industrial byproducts such as polysilicon sludge and paper ash used in this study is increasing. Blast furnace slag, which is one of the industrial byproducts, has been widely studied as a material used with cement. However, in this study, we fabricated lightweight matrix of polysilicon sludge and paper ash replaced based on blast furnace slag, and performed SEM analysis.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2017.11a
• /
• pp.167-168
• /
• 2017

In this research, the blast-furnace slag powder using the hydrometer also attempted to analysis the influence factor due to the temperature change of water and sample, and the number of upside down turns at the time of rapid evaluation. As a result, the influence of the number of turn was not large, but was the temperature of the water and sample are greatly affected.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2013.11a
• /
• pp.164-165
• /
• 2013

This study is on the performance evaluation of concrete being used the CaMg based low carbon cement(LCC) as a binder and the rapidly cooled electric arc furnace oxidizing slag(EAF slag) as a fine aggregate. When using the sand as a fine aggregate, compressive strength of the concrete using LCC, as a binder, was reduced 9% comparing with that of OPC concrete. However, when using the EAF slag as a fine aggregate, the compressive strength was increased by 9%. We found that combination LCC and EAF slag contribute to the strength properties of concrete.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2013.05a
• /
• pp.78-79
• /
• 2013

As a part of study to maximize the amount used of the ground granulated blast-furnace slag, the study deals with setting properties of paste that is mixed the ground granulated blast-furnace slag with CaO-Al₂O₃ based inorganic blinder. The results of the experiment show that the setting time is most fast in the mix of 25% rate of CaO-Al₂O₃ based inorganic blinder. It is generally needed 2 hours for work time in precast concrete products. In this study, this requirement is achieved when using the retarder of 0.5%.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2013.05a
• /
• pp.318-320
• /
• 2013

The spherical bead manufactured by rapidly cooling process shows high density of 3.64g/㎤, high unit volume weight of 2.6kg/l, and high solid volume of 71%. When it applies to the grouter, it is possible to obtain even high fluidity with only a small amount. This study, focusing the grouter using a rapidly-cooled electric arc furnace oxidizing slag(RC-EAFS), deals with the properties of flow and setting time in fresh state, compressive strength and length variation at 1, 3, 7 and 28 curing day in hardened state. As the results, even though the grouter with RC-EAFS shows comparative low strength, it will be possible to development the competitive product due to the properties of increasing flow and low cost.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2013.05a
• /
• pp.89-90
• /
• 2013

This study is to predict the compressive strength for the concrete of ground granulated blast-furnace slag, and use Plowman's, Gompertz's model. The results are as follows; The prediction compressive strength were simiar using Rastrup's equivalent age model. but The prediction compressive strength using Freiesleben's equivalent age model weren't simiar in bfs replacement Ratio of 50%, because it is analyzed as the activation energy.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2011.05a
• /
• pp.57-58
• /
• 2011

In the experiment, we add to NaOH, Ca(OH)₂ and Calcium Hydroxide as the Slag stimulus also mixed the cement stimulus such as NaSCN, TEA and CaCl₂ for improving compressive strenth of concrete which added the Blast Furnace Slag Powder at 1 and 3 days. In the result of strength test, It showed that 2percentage of activator 1 and 5percentage Ca(OH)₂, 1percentage of activator 3 and 5percentage of Ca(OH)₂ are higher than 100 percentage OPC.

• Journal of the Korean Society of Safety
• /
• v.18 no.4
• /
• pp.85-91
• /
• 2003

In this study, We have investigated leaching characteristics of heavy metals for recycled plastic composites containing EAF(Electric Arc Furnace) dust & EAF slag. EAF dust & EAF slag used that is generated in the 3 steel-making compaines in domestic. The physical and chemical properties of EAF dust & slag was examined by measuring specific surface area. porosity, oil absorption test and chemical wetting analysis etc. Results of total analysis indicated that EAF dust, slag contained significant amount of hazardous metals such as Cu, Pb, Cd and Cr. But, In the leaching test of the recycled plastic composites containing EAF dust, slag by Korean Standard Leaching Procedure, composites shows much lower leaching concentration of heavy metals. It was concluded that the recycled plastic composites containing EAF dust, slag showed good physical and chemical characteristics. This means that the EAF dust, slag can be effectively used as a functional filler.