• Fire Science and Engineering
• /
• v.22 no.4
• /
• pp.85-94
• /
• 2008

The purpose of this study is to obtain the fundamental fire resistance performance of engineered cementitious composites (ECC) under fire temperature in order to use the fire protection material in high-strength concrete structures. The present study conducted the experiment to simulate fire temperature by employing of ECC and investigated experimentally the explosion and cracks in heated surface of these ECC. In the experimental studies, 5 HSC specimens are being exposed to fire, in order to exami ne the influence of vari ous parameters (such as depth of layer=20, 30, 40 mm; construction method=lining and repairing type) on the fire performance of HSC structures. Employed temperature curve were ISO 834 criterion (3 hr), which are severe in various criterion of fire temperature in building structures. The numerical regressive analysis and proposed equation to calculate ambient temperature distribution is carried out and verified against the experimental data. By the use of proposed equation, the HSC members subjected to fire loads were designed and discussed.

• Structural Engineering and Mechanics
• /
• v.9 no.3
• /
• pp.241-256
• /
• 2000

The major sources of energy dissipation in steel frames with partially restrained (PR) connections are evaluated. Available experimental results are used to verify the mathematical model used in this study. The verified model is then used to quantify the energy dissipation in PR connections due to hysteretic behavior, due to viscous damping and at plastic hinges if they are formed. Observations are made for two load conditions: a sinusoidal load applied at the top of the frame, and a sinusoidal ground acceleration applied at the base of the frame representing a seismic loading condition. This analytical study confirms the general behavior, observed during experimental investigations, that PR connections reduce the overall stiffness of frames, but add a major source of energy dissipation. As the connections become stiffer, the contribution of PR connections in dissipating energy becomes less significant. A connection with a T ratio (representing its stiffness) of at least 0.9 should not be considered as fully restrained as is commonly assumed, since the energy dissipation characteristics are different. The flexibility of PR connections alters the fundamental frequency of the frame. Depending on the situation, it may bring the frame closer to or further from the resonance condition. If the frame approaches the resonance condition, the effect of damping is expected to be very important. However, if the frame moves away from the resonance condition, the energy dissipation at the PR connections is expected to be significant with an increase in the deformation of the frame, particularly for low damping values. For low damping values, the dissipation of energy at plastic hinges is comparable to that due to viscous damping, and increases as the frame approaches failure. For the range of parameters considered in this study, the energy dissipations at the PR connections and at the plastic hinges are of the same order of magnitude. The study quantitatively confirms the general observations made in experimental investigations for steel frames with PR connections; however, proper consideration of the stiffness of PR connections and other dynamic properties is essential in predicting the dynamic behavior.

• Steel and Composite Structures
• /
• v.36 no.3
• /
• pp.355-367
• /
• 2020

The current work, present dynamic analysis of the FG-sandwich plate seated on elastic foundation with various kinds of support using refined shear deformation theory. The present analytical model is simplified which the unknowns number are reduced. The zero-shear stresses at the free surfaces of the FG-sandwich plate are ensured without introducing any correction factors. The four equations of motion are determined via Hamilton's principle and solved by Galerkin's approach for FG-sandwich plate with three kinds of the support. The proposed analytical model is verified by comparing the results with those obtained by other theories existing in the literature. The parametric studies are presented to detect the various parameters influencing the fundamental frequencies of the symmetric and non-symmetric FG-sandwich plate with various boundary conditions.

• Asian-Australasian Journal of Animal Sciences
• /
• v.15 no.4
• /
• pp.494-499
• /
• 2002

The objectives of this study were to document the reproductive traits of mares as influenced by the month of the year in Taiwan. Reproductive records, lactation traits, foal birth weight (FBW) and foal height (FBH) were collected from Holi Equine Station of Taiwan. The effects of month on these parameters were analyzed. The length of estrus (LE) was shortest in December each year. The increasing trend was recorded from January to September with a significantly (p<0.05) longer period of $12.4{\pm}0.4$ days in September than in January and February. A gradual shortening in LE was observed from September to December ($10.1{\pm}0.6$ days, p<0.05), when the shortest period of the year was observed. Mares showed signs of estrus throughout the year, but more than 80% were found in estrus during March through October. The FBW was significantly (p<0.05) affected by the breeding month of the year. The lowest foal weights were recorded in both September ($36.7{\pm}0.7$ kg) and December ($36.8{\pm}0.9$ kg), which were also significantly lower than those in other months except in March, August, and November. A trend of lower FBH from September to December (93.5-93.8 cm) than those from January to August was observed. The greatest FBH was in June (96.2 cm). Breeding months and onset of estrus of the mares exerted a significant effect on the incidence of agalactia during the lactation period. These analyses provide fundamental information on adaptive processes in respect to reproductive characteristics of mares, which indicated an extent of acclimation by these animals in subtropical Taiwan.

• Journal of Fisheries and Marine Sciences Education
• /
• v.25 no.4
• /
• pp.928-936
• /
• 2013

This thesis is the fundamental study on the adaptation of escape device for reducing small fishes in set-net. The escape devices for experiments were made the mesh-type devices with three different mesh sizes (60.6, 75.8 and 120.0mm). The experiments of size selectivity on escape devices were conducted by using two kinds of species as black rockfish (Sebastes schlegeli) and sea perch (Lateolabrax maculatusi) in the experimental tank. The size selectivity curve was fitted by using a logistic function and the parameters of selectivity curve were estimated by a maximum likelihood method. In the results; 50% selection ranges for the mesh-type escape devices with three different mesh sizes were; a black rockfish was 18.99 in mesh size 60.6mm and 21.96 in mesh size 75.8mm (120mm could not estimate). A sea perch was 22.02 in mesh 60.6mm and 24.46 in mesh size 75.8mm (120mm could not estimate). The 50% selection range of a black rockfish was wilder than a sea perch about 1.1~.2 time. Therefore, the small fishes are able to reduce by using the mesh type escape device. However, the optimum mesh size should be decided to consider the size of target species and economics of catches.

• Applied Chemistry for Engineering
• /
• v.5 no.3
• /
• pp.537-546
• /
• 1994

The physical characteristics of polymer modified asphalt depend on many parameters, such as, the polymer nature, polymer content and the asphalt properties. The objective of this study is to investigate the temperature susceptibility of polymer modified asphalt. The asphalts employed in this study were two different grades : a soft(200/300) grade and a hard(85/100) grade. And chlorinated polyethylene of two different characteristics were used : plastomer(Tyrin 2552) and elastomer(Tyrin CM0730). Temperature susceptibility of asphalt is a fundamental feature for characterizing asphalt and modified asphalt. It can be quantified by the penetration index(PI) and pen-vis number(PVN). These indices were obtained from the measurements of penetration and viscosity of the asphalt samples. For both of asphalts, the addition of the polymers increases the value of PI and PVN. Plastomer modified asphalt shows higher value of PI and PVN than elastomer modified asphalt. Soft grade shows more temperature susceptibility than hard grade at elevated temperatures.

• Korean Journal of Environmental Biology
• /
• v.38 no.2
• /
• pp.222-230
• /
• 2020

Temperature-dependent development models for Hydrochara affinis were built to estimate the ecological parameters as fundamental research for monitoring the impact of climate change on rice paddy ecosystems in South Korea. The models predicted the number of lifecycles of H. affinis using the daily mean temperature data collected from four regions (Cheorwon, Dangjin, Buan, Haenam) in different latitudes. The developmental rate of each life stage linearly increased as the temperature rose from 18℃ to 30℃. The goodness-of-fit did not significantly differ between the models of each life stage. Unlike the optimal temperature, the estimated thermal limits of development were considerably different among the models. The number of generations of H. affinis was predicted to be 3.6 in a high-latitude region (Cheorwon), while the models predicted this species to have 4.3 generations in other regions. The results of this study can be useful to provide essential information for estimating climate change effects on lifecycle variations of H. affinis and studies on biodiversity conservation in rice fields.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.21 no.5
• /
• pp.549-555
• /
• 2001

Ultrasonic is a powerful nondestructive technique for getting the information of flaws and material properties of in-services facilities. We prepared 4 different 1Cr-1Mo-0.25V specimens by Isothermal aging at $630^{\circ}C$. We evaluated material degradation using ultrasonic parameters, velocity, attenuation and harmonic generation. Attenuation and nonlinear parameter derived from harmonic generation efficiency increased as degradation. Especially the second harmonic of the fundamental wave in the 1,820h aging material was observed to exceed 20dB more than that in the un-aged material. But velocity remained virtually the same for all specimens. We concluded that nonlinear parameter and attenuation are sensitive to material degradation, but velocity was not. It'll be a good parameter for evaluating the material degradation.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.3
• /
• pp.88-94
• /
• 2002

Recently, the life cycle and the lead-time of a product are to be shortened in order to satisfy consumer's demand. It is thus important to reduce the time and cost in manufacturing trial products. Several technique have been developed and successfully commercialized in the market of RPM(Rapid Prototyping and Manufacturing). However, most commercial systems currently use resins or waxes as the raw materials. So, the limited mechanical strength for functional testing is regarded as an obstacle towards broader application of rapid prototyping techniques. To overcome these problems, high-speed machining technology is being investigated worldwide for rapid manufacturing and even for direct rapid tooling application. In this paper, some fundamental experiments and analyses are carried out to obtain the filling time, materials, method, and process parameters for HisRP(High-Speed RP) process. HisRP is a new RP process that is combined high-speed machining with automatic filling. In filling process, Bi58-Sn alloy is chosen as filling material because of the properties of low-melting point, low coefficient of thermal expansion and no harm to environment. Also the use of filling wire it if advantage since it needs simple and flexible mechanism. Then the rapid product, for example a skull, is manufactured for aluminum material by HisRP process with an automatic set-up device thor 4-faces machining.

• Journal of Korean Society on Water Environment
• /
• v.22 no.6
• /
• pp.991-995
• /
• 2006

The layered double hydroxide with the insertion of chloride ions (LDH-Cl), which was synthesized by the co-precipitation method, was applied to investigate the fundamental aspects of the absorptive agent for phosphate removal from wastewater. The adsorption capacity was best described by the Langmuir-FreundIich isotherm, and the estimated isotherm parameters indicate that the LDH-CI capacity for the phosphate removal is much higher than that observed using a natural adsorbent material such iron oxide tailing. The kinetic experiment also showed that the LDH-Cl adsorption reaction rapidly at the adsorptive rate of 0.55 mg-P/g-LDH/min, implying that this adsorbent can be of use in the full-scale applications. The pH had a minimal effect on the LDH adsorption capacity in the range of 5 to 11, although the capacity dropped at the low pHs because of the change in LDH surface properties. Furthermore, other anions such as $Cl^-$ and $NO_3{^-}$ commonly found in the wastewater streams insignificantly affected the phosphate removal efficiencies, while $HCO_3{^-}$ ions had a negative effect on the LDH adsorption capacity due to its high selectivity. The phosphate removal experiment using the actual secondary effluent from a wastewater treatment plant showed the similar decrease in adsorption capacity, indicating that the bicarbonate ions in the wastewater were competing with phosphate for the adsorptive site in the surface of the LDH-Cl. Overall, the synthetic adsorbent material, LDH-Cl, can be a feasible alternative over other conventional chemical agents, since the LDH-Cl exhibits the high phosphate removal capacity with the low sensitivity to other environmental conditions.