• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.12
• /
• pp.9-24
• /
• 1995

In this paper, we proposed and analysed two kinds of priority control mechanism to archive the cell loss rate requirement and the delay requirement of each class. The service classes of our concern are the high time priority class(class 1) and the high loss priority class(class 2). Two kinds of priority control mechanism is divided by the method of storing the arriving class 2 cell in buffer on case of buffer full. The first one is the method which discarding the arriving class 2 cell, the second one is the mothod which storing the arriving class 2 cell on behalf of pushing out the class 1 cell in buffer. In the proposed priority schemes, one cell of the class 1 is transmitted whenever the maximum K cells of the class 2 is transmitted on case of transmitting the class 1 cell and the class 2 cell sequentially. In this paper, we analysed the cell loss rate and the mean cell delay for each class of the proposed priority scheme by using the Markov chain. The analytical results show that the characteristic of the mean cell delay becomes better for the class 1 cell and that of the cell loss rate becomes better for the class 2 cell by selecting properly the cell transfer ratio according to the condition of input traffic.

• Smart Structures and Systems
• /
• v.13 no.4
• /
• pp.547-565
• /
• 2014

This paper investigates the design of a perfect point load actuator based on flat triangular piezoelectric patches. Applying a difference of electric potential between the electrodes of a triangular patch leads to point loads at the tips and distributed moments along the edges of the electrodes. The previously derived analytical expressions of these forces show that they depend on two factors: the width over height (b/l) ratio of the triangle, and the ratio of the in-plane piezoelectric properties ($e_{31}/e_{32}$) of the active layer of the piezoelectric patch. In this paper, it is shown that by a proper choice of b/l and of the piezoelectric properties, the moments can be cancelled, so that if one side of the triangle is clamped, a perfect point load actuation can be achieved. This requires $e_{31}/e_{32}$ to be negative, which imposes the use of interdigitated electrodes instead of continuous ones. The design of two transducers with interdigitated electrodes for perfect point load actuation on a clamped plate is verified with finite element calculations. The first design is based on a full piezoelectric ceramic patch and shows superior actuation performance than the second design based on a piezocomposite patch with a volume fraction of fibres of 86%. The results show that both designs lead to perfect point load actuation while the use of an isotropic PZT patch with continuous electrodes gives significantly different results.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 2013.11a
• /
• pp.223-226
• /
• 2013

정확한 움직임 추정 기술은 원본과 가장 유사한 영상의 복원에 효과적이고 압축률에도 중요한 영향을 미친다. 하지만 기존의 전역 탐색 (Full Search) 알고리듬과 Sum of Absolute Difference (SAD)라는 정합 오차 기준은 연산량이 높고 하드웨어 구현시 비효율적이다. 이를 보완하기 위한 1비트 변환 알고리듬은 움직임 벡터의 변화량을 0과 1의 연산으로 나타내는데, 이 알고리듬은 움직임이 많아 픽셀 값의 변화가 심한 블록의 변화량도 0과 1로만 표현한다. 그렇기 때문에 정확한 움직임이 반영되지 않고 그로 인해 낮은 Peak Siganl to Noise Ratio (PSNR)을 가져온다. 이 점을 개선하고자 본 논문에서는 참조블록들의 움직임 벡터를 파악하고 분류하여 선택적으로 움직임의 변화량이 큰 영역은 전역 탐색 알고리듬을, 움직임이 작거나 없는 영역은 1비트 연산을 수행하도록 하여 기존의 알고리듬과 비교하여 Peak Siganl to Noise Ratio (PSNR)측면에서 우수한 성능을 확인할 수 있었다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.32 no.1
• /
• pp.1-6
• /
• 2008

This paper presents muscle-inspired serial digital actuators, achieving the improvement of the range-to-precision and range-to-voltage performance. We propose a weight-balanced design for the serial actuators with serpentine springs using serial arrangement of digital actuators. We have measured the displacement range, precision, and drive voltage at unit and serial actuation of 1Hz. The serial digital actuators produce a full range displacement of $28.44{\pm}0.02{\mu}m$, accumulating the unit displacement of $2.8{\pm}0.5{\mu}m$ at the operating voltage of $4.47{\pm}0.07V$. In addition, the serial digital actuators having the displacement precision of $37.94{\pm}6.26nm$ do not accumulate the precision of the unit actuators, $36.0{\pm}17.7nm$. We experimentally verify that the serial digital actuators achieve the range-to-squared-voltage ratio of $1.423{\mu}m/V^2$ and the range-to-precision ratio of 749.6.

• Fisheries and Aquatic Sciences
• /
• v.17 no.4
• /
• pp.441-448
• /
• 2014

We examined the effects of dietary nutrient content, feeding period, and feed allowance on compensatory growth, food use, chemical composition, and serum chemistry of juvenile olive flounder Paralichthys olivaceus. We placed 720 juvenile fish into 24 400-L flow-through round tanks (30 fish per tank).A $2{\time}2{\time}2$ factorial design (diet: control (C) and high protein and lipid (HPL) ${\time}$ feeding period: 8 and 6 weeks ${\time}$ feed allowance: 100% and 90% of satiation) was applied. Fish were hand-fed twice daily, based on the designated feeding schedule. Weight gain and food consumption were affected by both the feeding period and feed allowance, but not by diet. The food efficiency ratio was not affected by diet, feeding period, or feed allowance, but the protein efficiency ratio and protein retention were affected by diet and feeding period, respectively. We found that the full compensatory growth of fish was not achieved at a restricted feeding allowance.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.58-62
• /
• 2003

Silicon carbide (SiC) was etched in a $NF_3/CH_4$ inductively coupled plasma. The etch process was modeled by using a neural network called generalized regression neural network (GRNN). For modeling, the process was characterized by a $2^4$ full factorial experiment with one center point. To test model appropriateness, additional test data of 16 experiments were conducted. Particularly, the GRNN predictive capability was drastically improved by a genetic algorithm (GA). This was demonstrated by an improvement of more than 80% compared to a conventionally obtained model. Predicted model behaviors were highly consistent with actual measurements. From the optimized model, several plots were generated to examine etch rate variation under various plasma conditions. Unlike the typical behavior, the etch rate variation was quite different depending on the bias power Under lower bias powers, the source power effect was strongly dependent on induced dc bias. The etch rate was strongly correated to the do bias induced by the gas ratio. Particularly, the etch rate variation with the bias power at different gas ratio seemed to be limited by the etchant supply.

• Journal of Korean Society of Rural Planning
• /
• v.24 no.3
• /
• pp.55-62
• /
• 2018

This study analyze factors influencing business performance by types of agricultural corporation for improving performance. The number of agricultural corporations have been increasing but their profitability has been decreasing. In this situation, it is important to analyze factors influencing business performance for improving their profitability. We estimate a model including financial indexes and corporation's characters using ordinary least square. We use agricultural corporations survey data for 10years(2005~2014) of Statistics Korea. This study analyze bookkeeping recorded agricultural corporations for the same period. As a result, we find factors to influence Return on Assets(ROA). Additionally, we calculate optimized current ratio and debt ratio for ROA maximization. Operation period and the number of full-time workers also have a positive effect on ROA. Agricultural production, processing and distribution variables by business types have a positive effect on ROA, but some of their interaction terms have a negative effect on ROA. We expect that this result will help for improving corporation's business performance.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.24 no.3
• /
• pp.383-392
• /
• 2014

Purpose: In this study, we sought to understand the risk factor for chronic disease of workers by studying the association between occupational standing time and metabolic syndrome(MetS) in full-time 300 male workers. Materials: Data on age, life habit, work related information of the subjects were surveyed using self-reported questionnaire and interview. MetS was identified based on the report of Alberti et al.(2009). As for the data analysis, SPSS 19.0 was used to conduct the descriptive statistic, ANOVA, Pearson correlation coefficient and multiple logistic regression analysis. Results: Daily working hour affects on the lifting heavy objects, running and strenuous exercise(r=-0.137, p<0.01), and total physical function decreased with the increase in age(r=-0.145, p<0.01). Also, obese was significantly associated with genuflection and bend over(r=-0.110, p<0.05). On multiple logistic regression analysis for the diagnostic indices of MetS, occupational standing time were significantly associated with waist circumference(odds ratio=0.885, ${\beta}$ value=-0.122, 95% CI=0.797-0.983, p<0.05) and triglyceride (odds ratio=0.873, ${\beta}$ value=-0.136, 95% CI=0.800-0.953, p<0.01). Conclusions: These results suggest that the working posture may be important risk factor in pathogenesis and growing of MetS and cardiovascular disease.

• Journal of the Korean Solar Energy Society
• /
• v.25 no.2
• /
• pp.27-33
• /
• 2005

To improve the performance of the top-positioning space in buildings, we suggested the environment-friendly system integrating various design techniques in the previous paper. This work discussed to calculate the length of PV considering a part of metallic radiators for radiative cooling, an critical element of the whole system, for shading not to prevent the PV on roof from generating electricity. In the process of calculating the shading area, we used the geometrical relationship between the sun-rays and the variable roof. For general applications, we utilized DL, the ratio of the length of PV and that of metallic radiator on roof, as a design factor, and then used the maximum insolation and the specific insolation($200W/m^2$) to decide the distance off the axis of rotation. As a result, for DL, we found out the reasonable value of 1.0 with full covering, 1.2 with 90%, and 2.0 with 70% in PV covering.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.22 no.11
• /
• pp.788-797
• /
• 2010

This study examines the influence of fluctuating daylight illuminance on daylight dimming control systems. Field measurements were performed for a full-scale mocked-up model under various daylight conditions in winter. Fluctuating ranges for a partially-shielded photosensor were great when the variation of sky ratio was great. When solar altitude was lower the illuminance and fluctuating range of illuminance were great due to the influence of direct components of daylight and the interrefelction between surfaces in rear area of space. It implies that daylight dimming system would not function effectively, unless the desktop illuminance by daylight is enough. Fluctuation ranges of photosensor illuminance were lower than 50 lx under clear sky conditions, but they were greater than 100 lx under partly-cloudy sky conditions. It means that the fluctuation range of electric light output of lighting fixture would greater under the partly-cloudy conditions and cause potential visual annoyance to occupants. Outdoor vertical illuminance reaching the windows would be an effective factor that can be used to predict the fluctuation of photosensor signals for effective controls of daylight dimming system.