• Earthquakes and Structures
• /
• v.26 no.1
• /
• pp.77-86
• /
• 2024

To investigate the seismic performance of steel pipe-aeolian sand recycled concrete columns, this study designed and produced five specimens. Low-cycle repeated load tests were conducted while maintaining a constant axial compression ratio. The experiment aimed to examine the impact of different aeolian sand replacement rates on the seismic performance of these columns. The test results revealed that the mechanical failure modes of the steel pipe-recycled concrete column and the steel pipe-aeolian sand recycled concrete column were similar. Plastic hinges formed and developed at the column foot, and severe local buckling occurred at the bottom of the steel pipe. Interestingly, the bulging height of the damaged steel pipe was reduced for the specimen mixed with an appropriate amount of wind-deposited sand under the same lateral displacement. The hysteresis curves of all five specimens tested were relatively full, with no significant pinching phenomenon observed. Moreover, compared to steel tube-recycled concrete columns, the steel tube-aeolian sand recycled concrete columns exhibited improved seismic energy dissipation capacity and ductility. However, it was noted that as the aeolian sand replacement rate increased, the bearing capacity of the specimen increased first and then decreased. The seismic performance of the specimen was relatively optimal when the aeolian sand replacement rate was 30%. Upon analysis and comparison, the damage analysis model based on stiffness and energy consumption showed good agreement with the test results and proved suitable for evaluating the damage degree of steel pipe-wind-sand recycled concrete structures.

• The Journal of Internal Korean Medicine
• /
• v.45 no.1
• /
• pp.55-74
• /
• 2024

Objectives: This study reviewed the status of adverse event (AE) reporting in VigiAccess using anti-obesity agents as examples and explored the possibility of its use and future challenges. Methods: AE reports related to some representative drugs among herbal medicines (HMs), complex HM prescriptions, ingredients of supplements, and over-the-counter and prescription medicines were investigated using VigiAccess on February 1, 2024. Results: AE reports on prescription drugs were overwhelmingly higher than those on HMs or supplements. Although most reports were submitted from North America, reports on Ephedra sinica and green tea extract (GTE) were more from Asia and Europe, respectively. The female population reported more, and the difference in the sex ratio was the smallest for Ephedra spp. The age group was concentrated on young adults, but many older patients reported GLP-1 receptor agonist-related AEs. Symptoms related to the gastrointestinal and nervous systems were most commonly reported, but mental and cardiac disorders were common in Ephedra-type HMs. Hepatobiliary disorders are also commonly found in GTE-related reports. Conclusions: VigiAccess was useful for easily checking the global status of AE reporting for prescription drugs. However, several limitations were observed in using VigiAccess for HMs because of the few reports. Thus, it is necessary to increase the number of reports by education and to promote AE reporting among HM prescribers and users. The full range of HMs should be included in the pharmacovigilance system, and the coding and classification of HMs should be revised.

• Archives of Plastic Surgery
• /
• v.50 no.6
• /
• pp.621-626
• /
• 2023

In the first half of the third century B.C., Herophilus and Erasistratus performed the first systematic dissection of the human body. For subsequent centuries, these cadaveric dissections were key to the advancement of anatomical knowledge and surgical techniques. To this day, despite various instructional methods, cadaver dissection remained the best way for surgical training. To improve the quality of education and research through cadaveric dissection, our institution has developed a unique method of perforator-preserving cadaver injection, allowing us to achieve high-fidelity perforator visualization for dissection studies, at low cost and high efficacy. Ten full body cadavers were sectioned through the base of neck, bilateral shoulder, and hip joints. The key was to dissect multiple perfusing arteries and draining veins for each section, to increase "capture" of vascular territories. The vessels were carefully flushed, insufflated, and then filled with latex dye. Our injection dye comprised of liquid latex, formalin, and acrylic paint in the ratio of 1:2:1. Different endpoints were used to assess adequacy of injection, such as reconstitution of eyeball volume, skin turgor, visible dye in subcutaneous veins, and seepage of dye through stab incisions in digital pulps. Dissections demonstrated the effectiveness of the dye, outlining even the small osseous perforators of the medial femoral condyle flap and subconjunctival plexuses. Our technique emphasized atraumatic preparation, recreation of luminal space through insufflation, and finally careful injection of latex dye with adequate curing. This has allowed high-fidelity perforator visualization for dissection studies.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.27 no.3
• /
• pp.311-318
• /
• 2024

In this paper, a design for a radio frequency(RF) and infrared(IR) absorber with metasurfaces is discussed in microwave frequency bands. The RF absorber includes double layers of metasurfaces to operate in S- and X-bands. Effects of sheet resistance of the metasurfaces and thicknesses of dielectric supporting layers on reflection responses are investigated. An IR stealth layer incorporates an array of conductive grids with slits to reflect IR signals but to transmit RF signals and visible rays. Periodicity of the grids and slits is studied for transmission responses in the X-band and a surface area ratio. Reflection responses of the RF/IR multispectral absorber are found to be lower than -10 dB and -16 dB in the S- and X-bands, respectively, from full-wave simulation. Finally, the RF/IR multispectral absorber is fabricated and its reflection responses are measured to verify designed performance.

• Journal of the Korea Concrete Institute
• /
• v.24 no.6
• /
• pp.705-714
• /
• 2012

Precast reinforced concrete bridge columns with hollow rectangular section were tested under cyclic lateral load with constant axial force to investigate its seismic performance. After all the precast column segments were erected, longitudinal reinforcement was inserted in the sheath prefabricated in the segments, which were then mortar grouted. Main variables of the test series were column aspect ratio, longitudinal reinforcement ratio, amount of lateral reinforcement, and location of segment joints. The aspect ratios were 4.5 and 2.5, and the longitudinal steel ratios were 1.15% and 3.07%. The amount of lateral reinforcement were 95%, 55%, 50%, and 27% of the minimum amount for full ductility design requirements in the Korean Bridge Design Code. The locations of segment joints in plastic hinge region were 0.5 and 1.0 times of the section depth from the bottom column end. The test results of cracking and failure mode, axial-flexural strength, lateral load-displacement relationship, and displacement ductility are presented. Then, safety of the ductility demand based seismic design in the Korean Bridge Design Code is discussed. The column specimens showed larger ductility than expected, because buckling of longitudinal reinforcing bar was prevented due to confinement developed not only by transverse steel but also by sheath and infilling mortar.

• Asian-Australasian Journal of Animal Sciences
• /
• v.24 no.11
• /
• pp.1547-1551
• /
• 2011

Bakery waste (BW) is much cheaper than barley (20 to 40% the price of barley). Bakery waste and barley grain have similar chemical composition; they contain 99 and 97% organic matter (OM), 1.1 and 1.8% fat, 18 and 15% neutral detergent fibre (NDF) and 14.0 and 14.5% crude protein (CP), respectively (DM basis). The objectives of this study were to determine the effect of substituting BW for barley grain in high concentrate fattening diets for lambs on nutrient intake, growth and carcass characteristics. Forty Awassi lambs (21.75${\pm}$1 kg) weaned at the age of 65 days were assigned randomly to four experimental fattening diets differing in BW ratio in a completely randomized design. The control diet (CON) contained 20, 60, 11, 7, and 2% (DM basis) wheat straw, barley grain, soybean meal, corn grain, and minerals and vitamin mix, respectively. Bakery waste substituted barley grain by 10, 20 and 30% of the diet DM in the LBW, MBW and HBW diets, respectively. The experiment lasted for 56 days. Dry matter intake (DMI) decreased (p<0.05) in LBW diet compared to the CON diet by approximately 10%. No further reduction in DMI was observed with the higher substitution levels. Metabolizable energy intake for the CON diet (3.6 Mcal/d) was also reduced (p<0.05) compared with LBW, MBW and HBW diets (3.4, 3.4 and 3.3 Mcal/d, respectively). Final body weight for lambs fed the CON diet (34.8 kg) was higher (p<0.05) compared with lambs fed the LBW, MBW and HBW diets (30.6, 32.0 and 31.1 kg, respectively). Growth rate for lambs fed the CON diet (232 g/d) was also higher (p<0.05) compared to lambs fed the LBW, MBW and HBW diets (170, 189, and 167 g/d, respectively). Feed to gain ratio was higher (p<0.05) for lambs fed the LBW, MBW and HBW diets (7.2, 6.6 and 7.3, respectively) compared with lambs that consumed the CON diet (5.7). Body weight gain cost was reduced by approximately 8% by the MBW and HBW diets as compared with the CON diet. Dressing percentage, full gut weight, empty gut weight and liver weights were all unaffected by the BW addition to the diets and averaged 48.9%, 6.8 kg, 2.8 kg and 0.444 kg, respectively. However, fat tail weight was increased (p<0.05) with the higher levels of the BW inclusion. In conclusion, substituting BW for barley grain reduced DMI and growth performance. However, when BW substituted barley grain at the 20 and 30% of the diet DM, body weight gain cost was reduced by approximately 8%.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.18 no.3
• /
• pp.151-161
• /
• 2016

This study was conducted to find out influence of dormancy level and carbon concentration on freezing hardiness in bourse shoot of 'Fuji' apple tree. Bourse shoot of 'Fuji' adult apple tree grafted on M.26 and M.9 rootstocks were used as experimental materials. Dormancy levels of bourse shoot were categorized according to the periods as follows the internal dormancy (late January), the early days after internal dormancy breaking (early February), the late days after internal dormancy breaking (late February), the bud break (late March), and the full bloom (late April). Chilling temperatures with bourse shoot were ranged from 0 to $-40^{\circ}C$. Also, the freezing hardiness according to carbon concentrations were investigated on 'Fuji'/M.9 apple tree that defoliated severely by Marssonina blotch (defoliation) and that of below the average 20 cm in shoot length through heavy crop load (weakness). Results showed that freezing hardiness of bourse shoot may become weaker after internal dormancy breaking. There was no differences in the carbon concentration of bourse shoot of 'Fuji' apple tree grafted on M.9 and M.26, so may be resulted in no difference in freezing hardiness both of bourse shoot grafted on M.9 and M.26 rootstock. Carbon concentration in bourse shoots with weakness and C/N ratio in bourse shoots with defoliation were lower than that of healthy. It may be shown that the freezing hardiness of defoliation and weakness were weaker than that of healthy.

• Science of Emotion and Sensibility
• /
• v.13 no.3
• /
• pp.501-510
• /
• 2010

The knowledge base on emotional information is one of the key elements in the implementation of emotion retrieval systems for contents design of Mobile devices. This study proposed a new approach to the knowledge base implementation by automatically extracting color components from full-color images. In this study, the validity of the proposed method was empirically tested. Database was developed using 100 interior images as visual stimuli and a total of 48 subjects participated in the experiment. In order to test the reliability of the proposed 'emotional information knowledge base', firstly 'recall ratio' that refers to frequencies of correct images from the retrieved images was derived. Secondly, correlation Analysis was performed to compare the ratings by the subjects to what the system calculated. Finally, the rating comparison was used to run a paired-sample t-test. The analysis demonstrated satisfactory recall ration of 62.1%. Also, a significant positive correlation (p<.01) was observed from all the emotion keywords. The paired Sample t-test found that all the emotion keywords except "casual" retrieved the images in the order from more relevant to less relevant images and the difference was statistically significant (t(9)=5.528, p<.05). Findings of this study support that the proposed 'emotional information knowledge base' established only with color information automatically extracted from images can be effectively used for such visual stimuli search tasks as commercial interior images.

• Korean journal of food and cookery science
• /
• v.29 no.4
• /
• pp.353-359
• /
• 2013

The effect of the addition of dough ripe stage rice (DRSR) and yellow ripe stage rice (YRSR) on the quality characteristics of Backsulgi was investigated. The DRSR and YRSR addition ratio of 30% was selected by preliminary sensory evaluation study for which backsulgi was prepared with DRSR added to full ripe stage rice (FRSR, control) as the weight ratio of 0, 20, 30 and 50%. The pasting properties of 30% added DRSR and YRSR flours, analyzed with rapid viscosity analyzer (RVA), were compared with FRSR flour. The RVA values of holding, breakdown, final viscosities were higher in 30% DRSR and YRSR flours than in control. Backsulgi prepared with 30% DRSR and YRSR showed lower moisture content along with higher greenness and yellowness than control. As a result of analysis with texture analyzer, adhesiveness, springiness, cohesiveness, chewiness and resilience were lower in backsulgis with 30% DRSR and YRSR than in control. In the sensory evaluation, backsulgis with 30% DRSR and YRSR were assessed as having more intensive green color, and more greenish and delicious taste than control. Furthermore, backsulgi with 30% DRSR showed higher score of overall acceptability than 30% YRSR (p<0.05), and not significantly different score with control (p>0.05). Therefore, the addition of 30% DRSR could give favorable color and flavor to backsulgi.

• The Korean Journal of Nuclear Medicine Technology
• /
• v.20 no.2
• /
• pp.49-53
• /
• 2016

Purpose Recently, Cadmium-zinc-telluride (CZT) semiconductor myocardial SPECT (Single Photon Emission Computed Tomography) has been used myocardial scintigraphy. In this study, the performance of Semiconductor SPECT and conventional SPECT systems was compared by a comprehensive analysis of phantom SPECT images. Materials and Methods Methods: We evaluated the DSPECT CZT SEPCT (Spectrum-dynamic) and INFINA conventional (GE). Physical performance was compared on reconstructed SPECT images from a phantom. Results For count sensitivity on cardiac phantom images ($counts{\cdot}sec^{-1}{\cdot}MBq^{-1}$), DSPECT had a sensitivity of conventional SPECT. This classification was similar to that of myocardial counts normalized to injected activities from phantom images (respective mean values, $counts{\cdot}sec^{-1}{\cdot}MBq^{-1}$: 195.83 and 52.83). For central spatial resolution: DSPECT, 9.47mm; conventional SPECT, 16.90mm. For contrast-to-noise ratio on the phantom: DSPECT, 4.2; conventional SPECT, 3.6. Conclusion The performance of CZT cameras is dramatically higher than that of conventional SPECT. However, CZT cameras differ in that spatial resolution and contrast-to-noise ratio are better with conventional SPECT, whereas count sensitivity is markedly higher with the DSPECT.