• Journal of the Korean Electrochemical Society
• /
• v.19 no.3
• /
• pp.69-79
• /
• 2016

Lithium ion battery with high energy density is expanding its application area to electric automobile and electricity storage field beyond existing portable electric devices. Such expansion of an application field is demanding higher characteristic and stable long life characteristic of an anode material, the natural graphite that became commercialized in lithium ion battery. This thesis produced cathode by using natural graphite anode material, analyzed creation of the cathode SEI film created due to initial reaction by using electrolyte additives, VC (vinylene carbonate), VEC (vinyl ethylene carbonate), and FEC (fluoroethylene carbonate), and considered correlation with the accompanying electrochemical transformation. This study compared and analyzed the SEI film variation of natural graphite cathode according to the electrolyte additive with SEI that is formed at the time of initial filling and cathode of $60^{\circ}C$ life characteristic. At the time of initial filling, the profile showed changes due to the SEI formation, and SEI was formed in No-Additive in approximately 0.9 V through EVS, but for VC, VEC, and FEC, the formation reaction was created above 1 V. In $60^{\circ}C$ lifespan characteristic evaluation, the initial efficiency was highest in No-Additive and showed high contents percentage, but when cycle was progressed, the capacity maintenance rate decreased more than VC and FEC as the capacity and efficiency at the time of filling decreased, and VEC showed lowest performance in efficiency and capacity maintenance rate. Changes of SEI could not be verified through SEM, but it was identified that as the cycle of SEI ingredients was progressed through FT-IR, ingredients of Alkyl carbonate ($RCO_2Li$) affiliation of the $2850-2900cm^{-1}$ was maintained more solidly and the resistance increased as cycle was progressed through EIS, and specially, it was identified that the resistance due to No-Additive and SEI of VEC became very significant. Continuous loss of additives was verified through GC-MS, and the loss of additives from partial decomposition and remodeling of SEI formed the non-uniform surface of SEI and is judged to be the increase of resistance.

• Korean Journal of Plant Resources
• /
• v.28 no.1
• /
• pp.101-110
• /
• 2015

Parameters of mating system and pollen flow of a Pinus densiflora population in Buan, South Korea, were estimated using seven nuclear microsatellite markers. The expected heterozygosity ($H_e$) was 0.614 in mother trees and 0.624 in seeds. Fixation index (F) was 0.018 and 0.087 in each generation. There was no significant genetic difference between the generations (P > 0.05). From MLTR, the outcrossing rate ($t_m$), the biparental inbreeding ($t_m-t_s$), and the correlation of paternity ($r_p$) were 0.967, 0.057, and 0.012, respectively. tm was larger but $t_m-t_s$ and $r_p$ were smaller than those of allozyme markers in Pinus densiflora. These values were similar to those of microsatellite markers in other pine species. The optimal pollen dispersal model from TwoGener was the normal dispersal model with the effective density of 220 trees/ha and its level of genetic differentiation in pollen pool structure (${\Phi}_{ft}$) was 0.021. The average radial distance of pollen flow (${\delta}$) was calculated as 11.42 m, but no correlation between the pairwise-${\Phi}_{ft}$ and the geographical distance among mother trees was at Mantel test (r = -0.141, P > 0.05). Although the effective pollen dispersal in the population seems to be restricted, the amount of genetic variation might be maintained in each generation without a loss of genetic diversity. It might be because the genetic diversity in pollen pool was high but the genetic difference between pollen donors was small under the complete random mating condition in the Pinus densiflora population in Buan.

• Polymer(Korea)
• /
• v.32 no.2
• /
• pp.95-102
• /
• 2008

The $\alpha$,$omega$-diacrylate poly(dimethylsiloxane) (DA-PDMS) containing vinyl ester of versatic acid/vinyl acetate (Veova-10/VAc) was prepared by emulsion copolymerization of (DA-PDMS), Veova-10 (with VAc), and auxiliary agents at $85^{\circ}C$ in the presence of ammonium peroxodisulfate (APS) as an initiator. Sodium dodecyl sulfate (SDS) and nonylphenol ethylene oxide-40 units (NP-40) were used as anionic and nonionic emulsifiers, respectively. The resulting copolymers were characterized by using Fourier transform infrared spectroscopy (FT-IR). Thermal properties of the copolymers were studied by using thermogravimetric analysis(TGA) and differential scanning calorimetry (DSC). The morphology of copolymers was also investigated by scanning electron microscopy (SEM) and then the effects of variables such as temperature, agitation speed, surfactant kinds, molecular weights, initiator, and DA-PDMS concentrations on the properties of the silicone-containing Veova-10/VAc emulsions were examined. The calculation of monomer conversion versus time histories indicates that by increasing the DA-PDMS concentration the polymerization rate and the number of polymer particles decrease, respectively.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.2
• /
• pp.406-414
• /
• 2010

A novel polyacrylamide grafted hydrous ferric oxide adsorbent composite has been synthesized by using glow discharge electrolysis plasma. To optimize the synthesis conditions, the following parameters were examined in detail: applied power, discharge time, post polymerization temperature, post polymerization time, amount of crosslinking agent and hydrous ferric oxide gel added and so on. The adsorbent was characterized by Fourier transform infrared spectroscopy (FT-IR) and X-ray photoelectron spectroscopy (XPS). The removal percentage of the adsorbent in Pb(II) solution was examined and the data obtained showed that the adsorbent composite has a high capacity for lead ion. For the use in wastewater treatment, the thermodynamic and kinetic of Pb(II)-capture were also studied. Results indicated that the adsorption reaction was a spontaneous and an endothermic process, and it seems to be obeyed a pseudo-secondorder rate model. Moreover, the adsorption isotherm of Pb(II)-capture is following the Langmuir and Freundlich isotherm models.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.7
• /
• pp.1976-1980
• /
• 2010

A simple and reliable method has been developed to selectively separate and concentrate trace amounts of Fe(III) ions from water and food samples by using flame atomic absorption spectrometry. A new reagent, 5-hydroxy-4-ethyl-5,6-di-pyridin-2-yl-4,5-dihydro-2H-[1,2,4] triazine-3-thione, was synthesized and characterized by using FT-IR spectroscopy and elemental analysis. Effects of pH, concentration and volume of elution solution, sample flow rate, sample volume and interfering ions on the recovery of Fe(III) were investigated. The optimum pH was found to be 5. Eluent for quantitative elution was 10 mL of 2 M HCl. The preconcentration factor of the method, detection limit (3s/b, ${\mu}gL^{-1}$) and relative standard deviation values were found to be 25, 4.59 and 1%, respectively. In order to verify the accuracy of the method, two certified reference materials (TMDA 54.4 lake water and SRM 1568a rice flour) were analyzed. The results obtained were in good agreement with the certified values. The method was successfully applied to the determination of Fe(III) ions in water and food samples.

• The Korean Journal of Health Service Management
• /
• v.11 no.1
• /
• pp.171-180
• /
• 2017

Objectives : The objective of this study was to compare oral health behaviors and oral health indices between regular scaling group and irregular scaling group. Methods : This study was performed at M Dental Clinic in Busan on 352 dental patients treated between January 2014 and June 2015 using V6.0 software and medical interviews. The 352 patients were divided into 3 groups and oral health behavior (OHB) and oral health indices were compared. Results : The OHB scores significantly differed among Groups C and A. Group C had the lowest number of "Bad" scores for the Simplified Debris Index (S-DI), Simplified Calculus Index (S-CI), and Simplified Oral Hygiene Index (S-OHI). Groups B and A had the lowest number of "Excellent" scores. Group C had the lowest bleeding on probing (BOP), calculus rate (CR) and decayed teeth (DT). Furthermore, Group C had the highest number of missing teeth (MT) and filled teeth (FT). Conclusions : Patients who underwent regular scaling had the highest OHB and oral health index scores. This emphasizes the importance of regular scaling for prevention and early detection of oral disease.

• Journal of the Korean Society of Safety
• /
• v.32 no.1
• /
• pp.41-46
• /
• 2017

In this paper, from making an electrical fire which is thought to be the most damaging among potential dangers as a top event, minimal cut sets (MCS) about it were analyzed. For this, components of a power substation were classified into 15 items. Failure rates and modes were extracted based on Korea Electrical Safety Corporation, IEEE Gold Book, and RAC. To analyze the top event (an electrical fire), main events were assorted into "safety devices for overcurrent" and "ampere meter of detecter". Failure of components was divided into failure of VCB, COS, and MCCB. A fault tree was composed of 3 AND gate, 5 OR gates and 17 basic events. Overlapped events among the basic events are things which occur from relevant components. They were attached to the tree by distinguishing identifiers. In case of FT, two minimal cut sets of "IO_METER", "MF_METER", "DO_MCCB" and "IO_METER", "MF_METER", "DO_VCB" take 46% of electrical fires. Therefore, about basic events which are included in the top two minimum cut sets, strict control is necessary.

• Membrane and Water Treatment
• /
• v.11 no.3
• /
• pp.223-229
• /
• 2020

Here magnetic iron oxide particles (MIOPs) were synthesized under atmospheric air and which size was controlled by regulating the flow rate of alkali addition and used for efficient removal of bovine serum albumin (BSA) from water. The MIOPs were characterized using field-emission scanning electron microscopy (FE-SEM), Fourier transformation-Infrared spectroscopy (FT-IR) and vibrating sample magnetometer (VSM). The results revealed a successful preparation of the MIOPs. The removal efficiency for BSA using MIOPs was found to be about 100% at lower concentrations (≥ 10 mg/L). The maximum adsorption of 64.7 mg/g for BSA was achieved as per the Langmuir adsorption model. In addition, microfiltration membrane for removal of BSA as model protein organic foulant is also studied. The effect of various MIOPs adsorbent sizes of 210, 680 and 1130 nm on the absorption capacity of BSA was investigated. Water permeability of the BSA integrated with the smallest size MIOPs membrane was increased by approximately 22% compared by the neat BSA membrane during dead-end filtration. Furthermore, the presence of small size MIOPs were also effective in increasing the permeate flux.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2005.04a
• /
• pp.80-83
• /
• 2005

In this work, effects of oxygen plasma on surface characteristics of carbon fibers were investigated in mechanical properties interfacial of carbon fibers-reinforced composites. The surface properties of the carbon fibers were determined by acid/base values, FT-IR, and X-ray photoelectron spectroscopy (XPS). Also, the mechanical properties of the composites were studied in and critical stress intensity factor ($K_{IC}$) and critical strain energy release rate mode II ($G_{IIC}$) measurements. As experimental results, the $O_{lS}/C_{lS}$ ratio of the carbon fiber surfaces treated by oxygen plasma was increased compared to that of untreated ones, possibly due to development of oxygen-containing functional groups. The mechanical properties of the composites, including $K_{IC}$ and $G_{IIC}$ had been improved in the oxygen plasma on fibers. These results could be explained that the oxygen plasma was resulted in the increase of the adhesion of between fibers and matrix in a composite system.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.45 no.5
• /
• pp.64-70
• /
• 2013

In this study, the effect of soxhlet extraction on dewaxing of the aged beeswax-treated paper was examined. To do this, soxhlet extraction of the aged beeswax-treated paper performed with different reflux conditions and then measured the dewaxing efficiency and change in the various properties such as tensile strength, folding endurance, color and brightness. Also, an artificial aging test was executed in order to investigate the effect of soxhlet extraction on the preservability of the dewaxed paper. As the result of FT-IR analysis, a peak area of CH and COOH group, which are main band of beeswax, was decreased or removed after soxhlet extraction. The decreasing rate of each peaks were increased depending on reflux time. After dewaxing, the physical property such as MIT type folding endurance and tensile strength was decreased. And $L^*$ value and brightness were increased while $a^*$ and $b^*$ value were decreased due to the remove of color compounds in beeswax. The more color deviation (${\Delta}E$) is expected with higher reflux times. As the result of artificial aging, preservability of two dewaxed papers except of DP_SE(C) sample was higher than that of untreated paper i.e. beeswax-treated paper.