• International Journal of Aeronautical and Space Sciences
• /
• 제12권1호
• /
• pp.57-62
• /
• 2011

The effects of swirl chamber's diameter and length on injector's dynamic characteristics were investigated through an experimental study. A mechanical pulsator was installed in front of the manifold of a swirl injector which produces pressure oscillations in the feed line. Pressure in the manifold, liquid film thickness in the orifice and the pressure in the orifice were measured in order to understand the dynamic characteristic of the simplex swirl injector with varying geometry. A direct pressure measuring method (DPMM) was used to calculate the axial velocity of the propellant in the orifice and the mass flow rate through the orifice. These measured and calculated values were analyzed to observe the amplitude and phase differences between the input value in the manifold and the output values in the orifice. As a result, a phase-amplitude diagram was obtained which exhibits the injector's response to certain pressure fluctuation inputs. The mass flow rate was calculated by the DPMM and measured directly through the actual injection. The effect of mean manifold pressure change was insignificant with the frequency range of manifold pressure oscillation used in this experiment. Mass flow rate was measured with the variation of injector's geometries and amplitude of the mass flow rate was observed with geometry and pulsation frequency variation. It was confirmed that the swirl chamber diameter and length affect an injector's dynamic characteristics. Furthermore, the direction of geometry change for achieving dynamic stability in the injector was suggested.

• 한국도로학회논문집
• /
• 제7권4호
• /
• pp.203-210
• /
• 2005

바인더의 노화로 인한 성능변화는 침입도 또는 점도시험을 실시하여 판정하여왔다. 기존의 시험방법으로 아스팔트 바인더의 점탄성 특성과 실제거동을 평가할 수 없기 때문에 새로운 분석방법이 요구되어 왔다. 본 연구에서는 기존시험 방법을 사용하여 침입도지수와 잔류침입도를 판정하였고, 양방향 반복회전 모드와 일방향 반복회전 모드 시험을 실시하여 단기 노화된 아스팔트 바인더의 유변학적 특성을 분석하였다. 시험결과 단기 노화된 아스팔트 바인더는 시험주기(frequency) 즉, 차량속도의 변화에 따라 서로 다른 복합계수와 위상각을 나타냈으며 단기 노화 전후의 크리프 컴플라이언스 및 전단점도 시험결과에도 영향을 미치는 것으로 나타나서 포장 설계시 이러한 특성이 고려되어야 한다.

• 전력전자학회논문지
• /
• 제14권6호
• /
• pp.472-480
• /
• 2009

본 논문은 3상 NPC형 3레벨 인버터의 과변조 SVPWM 기법과 변조비에 대한 출력전압의 고조파를 분석하였다. 3상 NPC형 3레벨 인버터는 SVPWM을 적용하여 선형영역을 0.907까지 확장하였고 과변조 영역에서는 푸리에 급수에 의한 추종전압의 보상기법을 적용하여 6 스텝영역까지 운전할 수 있도록 하였다. PWM 형태인 출력전압의 고조파 특성분석에는 PD방식의 멀티 캐리어 기법에 대하여 이중 푸리에 급수를 적용하여 해석하였다. 시뮬레이션은 PSIM을 사용하여 구현하였고 3레벨 인버터의 영역도의 각 영역에 대해서 고조파의 특성을 확인하였다. NPC형 3레벨 인버터의 고조파 분포는 선형영역에서는 캐리어 주파수의 측대 고조파가 분포되고, 과변조 영역으로 넘어가면서 기본파에 의한 고조파 성분이 점차 증가하고 캐리어 주파주의 사이드 밴드의 고조파 성분은 감소함을 확인하였다. 본 논문에서의 고조파 해석을 검증하기 위하여 동일한 조건에서 시뮬레이션과 실험을 수행하였다.

• 한국전기전자재료학회논문지
• /
• 제17권8호
• /
• pp.840-845
• /
• 2004

The microstructure and microwave dielectric properties of $(1-x){Mg}_4{Ta}_2{O}_9-xTi{O}_2(x=0\sim0.9)$ ceramics were investigated. The specimens were prepared by the conventional mixed oxide method with sintering temperature of 140$0^{\circ}C$∼150$0^{\circ}C$. To improve the quality factor and the temperature coefficient of resonant frequency,$ Ti{O}_2(\varepsilon\Gamma=100, Q\times f_\Gamma=40,000 GHz,\ta_f= +450 ppm\diagup^{\circ}C $ was added in ${Mg}_4{Ta}_2{O}_9$ceramics. The dielectric and structural properties were investigated. According to the XRD patterns, $(1-x){Mg}_4{Ta}_2{O}_9-xTi{O}_2(x=0\sim0.9)$ ceramics had the ${Mg}_4{Ta}_2{O}_9$ phase(hexagonal) and ${MgTi}_2{O}_5$phase(orthorhombic). The dielectric constant($\varepsilon_r$). quality($Qtimes{f}_r$${\tau}_f$) of the $(1-x){Mg}_4{Ta}_2{O}_9-xTi{O}_2(x=0\sim0.9)$ ceramics were 8.12∼18.59, 18,750∼186,410 GHz and －36.02∼＋3.46 ppm/$^{\circ}C$, respectively.

• 천문학회지
• /
• 제48권5호
• /
• pp.237-255
• /
• 2015

The Interferometric Monitoring of Gamma–ray Bright Active galactic nuclei (iMOGABA) program provides not only simultaneous multifrequency observations of bright gamma–ray detected active galactic nuclei (AGN), but also covers the highest Very Large Baseline Interferometry (VLBI) frequencies ever being systematically monitored, up to 129 GHz. However, observation and imaging of weak sources at the highest observed frequencies is very challenging. In the second paper in this series, we evaluate the viability of the frequency phase transfer technique to iMOGABA in order to obtain larger coherence time at the higher frequencies of this program (86 and 129 GHz) and image additional sources that were not detected using standard techniques. We find that this method is applicable to the iMOGABA program even under non–optimal weather conditions.

• 대한방사선기술학회지:방사선기술과학
• /
• 제18권2호
• /
• pp.49-59
• /
• 1995

Recently, general radiography became to variety because of the continuous development of Inverter type generator and ortho chromatic system. Therefore, we must re-evaluate about patient exposure dose and image quality. I studied about chest radiography which has frequency among general radiography being used during FEB. to AUG., 1994 over 151 medical facilities from medical facilities that are located in Seoul area. The result obtained were as follows ; 1) The rectification method of the generator were employing mainly single phase full wave in 82.8 %, three phase full wave in 11.26 % and Inverter type in 4.64 % and condenser type is 1.32 %. 2) Exposure kV was used below 80 kV in most medical facilities and 21.8 % of the medical facilities was using high tube voltage higher than 120 kV. 3) The exposure time was used below the 0.05 sec in 28.4 %, in 29.8 % of the medical facilities used above 0.1 sec. 4) The usage frequency of the added filter is 15.3 %, and among them compound filter was used only 4 %. 5) Rare earth screen was used in 37.7 %. 6) The average skin entrance dose was 0.25 mSv, the range of dose is $0.05{\sim}0.79\;mSv$ in each medical facilities. 7) The average density of the lung field is 1.76, 0.49 in lung side, 0.30 in mediastinum and 0.37 in heart shadow. Therefore it is required to improve all of these for increasing image quality and reducing patient exposure dose as soon as possible.

• 대한조선학회논문집
• /
• 제56권5호
• /
• pp.418-426
• /
• 2019

To derive a simplified analytic solution which can be utilized as a fundamental solution for the wave maker design, a segment of the wave board has been idealized as a submerged line segment in a two dimensional domain of a wave flume. The lower end of the line segment could be located at arbitrary depth of the wave flume and the upper end of the board could be also submerged to any depth from the free surface. The freely oscillating motion of the wave board is assumed to be defined by determining the condition of horizontal oscillation on both ends differently. The submerged wave board oscillating in horizontal direction could be specified by selecting the amplitude, frequency and the phase lag differently on lower and upper ends of the board. The simplified two dimensional wave generated by the wave board segment has been obtained by the first order perturbation method. It is found that the general solution of the freely oscillating wave board in two dimensional domain could be decomposed into the solution of flap motion with lower end hinge and swing motion with upper end hinge. The case study of the analytic solutions has been carried out to evaluate the effect on the wave height due to the difference of oscillation frequency, phase difference and variation of stroke between for the motion of both ends. It is found that the solution of the freely oscillating wave board could be utilized for the development of high performance wavemaker especially for irregular waves.

• 한국재료학회지
• /
• 제8권6호
• /
• pp.526-531
• /
• 1998

HVPE(hydride vapor phase epitaxy)법으로 (111) $MgAl_2O_4$기판 위에 $10~240\mu{m}$두께의 GaN를 성장하고, GaN의 두께에 따 광학적 성질을 조사하였다. $MgAl_2O_4$기판 위에 성장된 GaN의 PL 특성은 결정성장온도에서 기판으로부터 Mg이 out-diffusion하여 auto-doping 됨으로써 불순물이 첨가된 GaN의 PL 특성을 나타내었다. 10K의 온도데서 측정된 PL 스펙트럼은 자유여기자와 속박여기자의 재결합천이에 의한 피크들과 불순물과 관련된 도너-억셉터 쌍 사이의 재결합 및 이의 포논 복제에 의한 발광으로 구성되었으며, 깊은 준위로부터의 발광은 나타나지 않았다. 중성 도너에 속박된 여기자 발광 에너지와 라만 $E_2$모드 주파수는 GaN의 두께가 증가함에 따라 지수 함수적으로 감소하였으며, GaN 내의 잔류 응력에 대하여 라만 E2 모드 주파수는$\Delta$$\omega$=3.93$\sigma$($cm^{-1}$/GPa)의 관계로 변화하였다.

• 조명전기설비학회논문지
• /
• 제20권3호
• /
• pp.36-44
• /
• 2006

일반적으로 PWM인버터에 발생된 고조파와 노이즈는 스위칭 주파수, dv/dt와 di/dt, PWM 스위칭 방법에 의해 영향을 받는다. 멀티레벨 인버터가 고전력 시스템에 적용되어 낮은 주파수에서 동작할 때 이것은 큰 고조파 성분과 노이즈를 발생하게 된다. 따라서 멀티레벨 인버터에 출력 필터가 요구된다. 본 논문에서는 H-bridge 7레벨 인버터 시스템을 사용한 3상 유도 전동기 구동 시스템의 고조파와 노이즈 감소를 위해 출력 필터를 설계하였다. 가격이 저렴하고 간단한 구조를 가지며, 고조파와 노이즈를 효과적으로 감소시킬 수 있는 수동필터는 멀티레벨 인버터 시스템을 사용한 3상 유도전동기 구동시스템에 적용되었다. 설계된 시스템은 향상되었고, 시뮬레이션과 실험을 통해 그 타당성을 증명하였다.

• 전기학회논문지
• /
• 제60권11호
• /
• pp.2000-2006
• /
• 2011

Asynchronous phenomenon occurs on the synchronous generators under power system when a generator's amplitude of electromagnetic force, phase angle, frequency and waveform etc become different from those of other synchronous generators which can follow instantly varying speed of turbine. Because the amplitude of electromagnetic force, phase frequency and waveform differ from those of other generators with which are to be put into parallel operation due to the change of excitation condition for load sharing and the sharing load change, if reactive current in the internal circuit circulates among generators, the efficiency varies and the stator winding of generators are overheated by resistance loss. Where calculation method of protection settings and Logic for Protection of Generator Asynchronization will be recommended, A distance relay scheme is commonly used for backup protection. This scheme, called a step distance protection, is comprised of 3 steps for graded zones having different operating time. As for the conventional step distance protection scheme, Zone 2 can exceed the ordinary coverage excessively in case of a transformer protection relay especially. In this case, there can be overlapped protection area from a backup protection relay and, therefore, malfunctions can occur when any fault occurs in the overlapped protection area. Distance relays and overcurrent relays are used for backup protection generally, and both relays have normally this problem, the maloperation, caused by a fault in the overlapped protection area. Corresponding to an IEEE standard, this problem can be solved with the modification of the operating time. On the other hand, in Korea, zones are modified to cope with this problem in some specific conditions. These two methods may not be obvious to handle this problem correctly because these methods, modifying the common rules, can cause another coordination problem. To overcome asynchronizing protection this paper describes an improved backup protection coordination scheme using a new Logic that will be suggested.