• Ocean Systems Engineering
• /
• 제14권3호
• /
• pp.301-314
• /
• 2024

In this study, the lift coefficient and wave deformations for a two-dimensional flat-plate in non-cavitating condition were computed using a closed-form (analytic) solution. This plate moves at a constant speed beneath a free surface in water of finite depth. The model represents the flat-plate using a lumped vortex element within the constraints of potential flow theory. The kinematic and dynamic free surface conditions were combined and linearized. This linearized free surface condition was then applied to get the total velocity potential. The method of images was utilized to account for the effects of finite depth in the calculations. The lift coefficient of the flat-plate and wave elevations on the free surface were calculated using the closed-form solution. The lift coefficients derived from the present analytic solution were validated by comparing them with Plotkin's method in the case of deep water. Wave elevations were also compared with those obtained from a numerical method. A comprehensive discussion on the impact of Froude number, submergence depth of flat-plate from the calm free surface, the angle of attack and the depths of finite bottom on the results - namely, lift coefficients and free surface deformations - is provided.

• 대한조선학회지
• /
• 제19권2호
• /
• pp.13-18
• /
• 1982

The method of Rankine source distribution is emerging as a powerful yet simple alternative for the solution of complicated free surface problems. But it has been uncertain whether the radiation condition could be satisfied exactly by distributing the simple sources on the free surface only. In this paper, it is proved rigorously that the Rankine sources, whose intensities are varying sinusoidally along the axis satisfying the free surface boundary condition, generate the radiation waves both in the infinite and finite-depth flows. A formula is derived to give the upper and lower bounds of the errors in the induced velocity computation that will be introduced by truncating the extent of source distribution on the free surface. Since the truncation is inevitable in the numerical analysis, this formula may be used as a criterion to limit the position of the field points, where velocity computation is made, away from the truncation boundary. A typical analysis shows that the maximum error will be 3.4 percent of the exact induced velocity when the field point is on the free surface two wave lengths away from the truncation boundary.

• 한국운동역학회지
• /
• 제26권3호
• /
• pp.257-264
• /
• 2016

Objective: The purpose of this study was to determine the periodicity of shank-foot segment coupling and free torque before and after fatigue induced by prolonged running. Method: Fifteen young healthy male participants with a rear-foot strike ran on instrumented dual-belt treadmills at 70% of their maximum oxygen uptake for 65 min. Kinematic and ground reaction force data were collected for 20 continuous strides at 5 and 65 min (considered the fatigued condition). The approximate entropy tool was applied to assess the periodicity of the shank internal-external rotation, foot inversion-eversion, shank-foot segment coupling, and free torque for the two running conditions. Results: The periodicity of all studied parameters, except foot inversion-eversion, decreased after 65 min of running (fatigued condition) for 80% of the participants in this study. Furthermore, 60% of the participants showed similarities in the change of periodicity pattern in shank internal-external rotation, coupling, and free torque. Conclusion: The findings indicated that the foot inversion-eversion motion may pose a higher risk of injury than the shank internal-external rotation, coupling, and free torque in the fatigued condition during prolonged running.

• 한국방재학회 논문집
• /
• 제10권1호
• /
• pp.103-109
• /
• 2010

본 연구에서는 자유수면 흐름에 적용할 수 있는 연직방향에 대해 좌표변환된 3차원 동수압 모형을 제시하였다. 제시한 모형은 자유수면과 동수압의 해석을 위하여, 2중 예측-수정(double predictor-corrector)방법을 적용하였다. 본 연구에서는 정확한 동역학적 경계조건(자유수면에서의 압력은 0인 조건)을 적용하는 방법을 검토하였고, 제시한 모형을 이용한 수치모의 결과를 해석해와 비교하여 본 연구에서 제시한 모형의 우수성을 검증하였다.

• 한국해양공학회지
• /
• 제12권2호통권28호
• /
• pp.97-110
• /
• 1998

The numerical damping and dispersion error characteristics associated with difference schemes and a panel shift method used for the calculation of steady free surface flows by a panel method are an analysed in this paper. First, 12 finite difference operators used for the double model flow by Letcher are applied to a two dimensional cylinder with the Kelvin free surface condition and the numerical errors with these schemes are compared with those by the panel shift method. Then, 3-D waves due to a submerged source are calculated by the difference schemes, the panel shift method and also by a higher order boundary element method(HOBEM). Finally, the waves and wave resistance for Wigley's hull are calculated with these three schemes. It is shown that the panel shift method is free of numerical damping and dispersion error and performs better than the difference schemes. However, it can be concluded that the HOBEM also free of the numerical damping and dispersion error is the most stable, accurate and efficient.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2000년도 봄 학술발표회 논문집
• /
• pp.159-166
• /
• 2000

Non-destructive out-hole tests, impact-echo and impact-response are widely applied to evaluate integrity of drilled shafts. In these tests, vibratory motions of drilled shafts are interpreted, which induced by impacts on the shaft head. In applying the tests to evaluating integrity of shaft, it has been attended whether the tests have resolutions enough to distinguish existence of slime at between the shaft end and a bearing soil deposit. To distinguish existence of slime by tests, modes of shaft vibrations need to be reasonably interpreted, which generally vary according to a shaft boundary condition such as, a free-free or a free-fixed condition. The boundary condition of a shaft is, however, found to be significantly affected by stiffness of soil deposits around shaft as well as penetration depths of shaft into a bearing soil deposit. Thus, these effects on the boundary condition of a shaft should be considered reasonably in interpreting test results to decide the existence of slime. To investigate the effects, in this study, vibratory motions of shafts constructed in various soil conditions and end penetration depths are examined analytically. Based on the studies, variations of boundary condition are characterized in terms of soil stiffness contrast between a shaft perimeter and a shaft end, and also the ratio of a penetration depth to a shaft length. The results can be applied to verify the applicability of tests to identify the slime.

• Ocean Systems Engineering
• /
• 제6권3호
• /
• pp.245-264
• /
• 2016

The iterative boundary element method (IBEM) developed originally before for cavitating two-dimensional (2-D) and three-dimensional (3-D) hydrofoils moving under free surface is modified and applied to the case of 2-D (two-dimensional) airfoils and 3-D (three-dimensional) wings over water. The calculation of the steady-state flow characteristics of an inviscid, incompressible fluid past 2-D airfoils and 3-D wings above free water surface is of practical importance for air-assisted marine vehicles such as some racing boats including catamarans with hydrofoils and WIG (Wing-In-Ground) effect crafts. In the present paper, the effects of free surface both on 2-D airfoils and 3-D wings moving steadily over free water surface are investigated in detail. The iterative numerical method (IBEM) based on the Green's theorem allows separating the airfoil or wing problems and the free surface problem. Both the 2-D airfoil surface (or 3-D wing surface) and the free surface are modeled with constant strength dipole and constant strength source panels. While the kinematic boundary condition is applied on the airfoil surface or on the wing surface, the linearized kinematic-dynamic combined condition is applied on the free surface. The source strengths on the free surface are expressed in terms of perturbation potential by applying the linearized free surface conditions. No radiation condition is enforced for downstream boundary in 2-D airfoil and 3-D wing cases and transverse boundaries in only 3-D wing case. The method is first applied to 2-D NACA0004 airfoil with angle of attack of four degrees to validate the method. The effects of height of 2-D airfoil from free surface and Froude number on lift and drag coefficients are investigated. The method is also applied to NACA0015 airfoil for another validation with experiments in case of ground effect. The lift coefficient with different clearance values are compared with those of experiments. The numerical method is then applied to NACA0012 airfoil with the angle of attack of five degrees and the effects of Froude number and clearance on the lift and drag coefficients are discussed. The method is lastly applied to a rectangular 3-D wing and the effects of Froude number on wing performance have been investigated. The numerical results for wing moving under free surface have also been compared with those of the same wing moving above free surface. It has been found that the free surface can affect the wing performance significantly.

• 한국표면공학회지
• /
• 제25권4호
• /
• pp.181-186
• /
• 1992

To investigate how to produce the crack free and chromium deposits, bath compositions, additives, electrolysis conditions and other electroplating parameters, such as cathodic current efficiency, surface hard-ness, crack density and corrosion rate of deposits were examined carefully. The crack free chrome deposits were well obtained using both wetting agents and two kind of additives. At 60 A/d$\m^2$, $60^{\circ}C$ electrolysis condition, crack free bright hard chromium deposits were well obtained to a thickness $300\mu\textrm{m}$ in Additive-I and Additive-II added solution.

• Ocean Systems Engineering
• /
• 제7권4호
• /
• pp.371-398
• /
• 2017

Calm water wave resistance plays a very important role in ship hull design. Numerical methods are meaningful for this reason. In this study, two prevailing methods, the Neumann-Kelvin and the Rankine source method, were implemented and compared. The Neumann-Kelvin method assumes linearized free surface boundary condition and only needs to mesh the hull surface. The Rankine source method considers nonlinear free surface boundary condition and meshes both the ship hull surface and free surface. Both methods were implemented and the wave resistance of a Wigley III and three Series 60(Cb=0.6, 0.7, 0.8) hulls were analyzed. The results were compared with experimental results and the merits of both numerical techniques were quantified. Based on the results, it is concluded that the Rankine source method is more accurate in the calculation of the wave-making resistance. Using the Neumann-Kelvin method, it is found to be easier to model the hull and can be used for slender ships to solve problems like wave current coupling calculation.

• 대한토목학회논문집
• /
• 제28권6B호
• /
• pp.691-696
• /
• 2008

본 연구에서는 자유수면 흐름에 적용할 수 있는 연직방향에 대해 좌표변환된 3차원 동수압 모형을 제시하였다. 제시한 모형은 자유수면과 동수압의 해석을 위하여, 2중 예측-수정(double predictor-corrector)방법을 적용하였다. 본 연구에서는 정확한 동역학적 경계조건(자유수면에서의 압력은 0인 조건)을 적용하는 방법을 검토하였고, 이 경계조건은 기존에 개발된 모형에 미소한 수정을 통하여 적용 가능함을 보여주었다. 본 연구에서 제시한 모형과 기존 모형의 계산결과를 비교하였을 때 동역학적 경계조건의 정확한 적용이 매우 중요함을 알 수 있다.