• 한국식품영양학회지
• /
• 제21권1호
• /
• pp.56-63
• /
• 2008

This study investigated the quality characteristics of breads manufactured with xylito1. Four different concentrations(0, 5, 7, and 10%) of xylitol were added to the bread-making flour. Volume, color, the visco-elastic properties of the dough, and bread texture were analyzed. The dough volumes of the xylitol treatments during fermentation, as well as the final volumes of the xylitol breads were lower than those of the control dough and bread. Onset temperature slightly increased with the xylitol concentration, but entalphy changed minimally. Finally, the hardness of the bread positively increased with the xylitol concentration.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2006년 추계학술발표대회 개요집
• /
• pp.169-171
• /
• 2006

Solderability and reaction properties were investigated for four Pb-free alloys as a function of Ag contents; Sn-4.0Ag-0.5Cu, Sn-3.0Ag-0.5Cu, Sn-2.5Ag-0.5Cu, and Sn-1.0Ag-0.5Cu. The alloy of the lowest Ag content, i.e., Sn-1.0Ag-0.5Cu, showed poor wetting properties as the reaction temperature decreased to 230oC. Variation of Ag concentration in the Sn-xAg-0.5Cu alloy shifted exothermic peaks indicating the undercooling temperature in DSC curve. For the aging process at 170oC, the thickness of IMCs at the board-side solder/Cu interface increased with the Ag concentration.

• 한국세라믹학회지
• /
• 제31권10호
• /
• pp.1169-1175
• /
• 1994

Five Al2O3/SiC/metal composites with four different particle sizes of green SiC abrasive grains are grown by the directed oxidation of an commercially available Al-alloy. Oxidation was conducted in air at 100$0^{\circ}C$, 96 hours long. Slip casted SiC-fillers were placed on the alloy or SiC powder deposited up to the required layer thickness. Their microstructures are described and measurements of density, elastic constants, frexural strength, fracture toughness and work of fracture are reported. The results are compared with those of commercial dense sintered Al2O3. The properties of produced materials have a strong relationship to not only the properties of Al2O3, SiC, Al and Si but also to the phase share and phase distribution. The composite materials are dense (0.5% porosity), tough (KIC = 3.4~6.4 MPa{{{{ SQRT { m} }}), strong ({{{{ sigma }}B = 170~345 MPa) and reasonably shrinkage free producible. The reinforcements is attained mainly through the plastic deformation of ductile metal phase.

• 대한가정학회지
• /
• 제27권1호
• /
• pp.1-8
• /
• 1989

In order to investigate the mechanical properties such as tensile, bending, shearing, thickness and weight of the wool fabrics were measured by KES-F system. Samples were classified into blend ratio, weave type, fabric count. Blend ratio was classified into two groups, which are P/W blended fabric (p=63~65%, w=35~37%) and all wool fabric. Weave type was classified into four groups, which are plain, 3 harness twill, 4harness twill, satin. Cloth count was classified into three groups, which are loose, medium, tight. Statistical analysis was performed using T-test, F-test. The results were as follows; 1. There was significant difference in the thickness, tensile, bending, shearing according to the blend ratio. 2. According the weave, there was significant difference in the bending, weight and thickness in the P/W blended fabrics. There was significant difference in the tensile, weight, thickness, bending, shearing, shearing hysterisis (2HG) in the all wool fabrics. 3. There was significant difference in the shearing properties according to the fabric count.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1989년도 하계종합학술대회 논문집
• /
• pp.333-334
• /
• 1989

Electrically active part of the piezoelectric sound element is a ceramic thin circular disk cemented to a metal base plate (using a type of thermosetting epoxy). The active part is a thin lead zirconate titanate disk (PZT). The piezoelectric sound element is so dimensioned that its basic resonance frequency is approximately if the center of the audible frequency band: This frequency is mainly determined by the geometry and the sort of the metal base plate materials. In this study, four kinds of PZT ceramic and two classes of thin metal base plate were prepared. It is observed that dielectric and pizoelectric properties relate to acoustical properties (particularly sound pressure level).

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 하계학술대회 논문집
• /
• pp.336-336
• /
• 2010

Ga doped ZnO (GZO) transparent conductive films were deposited on the glass substrates at room temperature by facing target sputtering (FTS) method. The sputtering targets were 100 mm diameter disks of GZO($Ga_2O_3$ 3.w.t%) and Zn metal. The GZO thin films were deposited as a various $PO_2$ (oxygen gas content). Base pressure was $2{\times}10^{-6}$torr, and a working pressure was 1mTorr. The properties of thin films on the electrical and optical properties of the deposited films were investigated by using a four-point probe, a Hall Effect measurement and an UV/VIS spectrometer. The minimum resistivity of film was $6.5{\times}10^{-4}$[$\Omega$-cm] and the average transmittance of over 80% was seen in the visible range.

• 전자공학회논문지A
• /
• 제29A권8호
• /
• pp.49-55
• /
• 1992

We Have investigated the properties of the titanium nitrite films widely used in VLSI devices as diffusion barrier in Al-based metallization. TiN films were formed by reactive sputtering from Ti target in Ar-N$_2$ mixtures, varying deposition parameters such as N$_2$ partial pressure, substrate temperature, power, and total pressure. All the samples received the heat treatment at 45$0^{\circ}C$ for 30 min. The resulting films are characterized by mechanical stylus($\alpha$-step), x-ray diffraction(XRD), scanning electron microscopy(SEM), and four point probe method. The Tin film properties strongly depend on the deposition condition. The stoichiometry and Ti deposition rate are critically affected by nitrogen partial pressure, and the resistivity, in particular, is dependent on both the substrate temperature and sputtering power.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 1999년도 추계학술발표대회 논문집
• /
• pp.234-238
• /
• 1999

This study suggests the design of the functionally gradient composite, [0/90/0/core]$_s$ cross-ply laminate, to prevent stress concentration induced from the difference of rigidity between the bone and the artificial hip joint and to reinforce the wear property of the surface and the expectation of their mechanical properties. First, the four-point bending test is done about wet bones and dry bones to know the mechanical properties of the cortical bones. In result, the wet bone shows the viscoelastic behavior and the dry bone shows the elastic behavior. Moreover, we expect the properties of the proposed gradient composites as a function of carbon fiber volume fraction in each layer to apply Halpin-Tsai equation, CLPT(classical laminate plate theory), and Bernoulli beam theory etc. and decide the thickness ratio of each lamina in order to match Young's modulus of the anisotropic cortical bone with the proposed gradient composites.

• Rapid Communication in Photoscience
• /
• 제2권2호
• /
• pp.52-55
• /
• 2013

Proteorhodopsin (PR) is a photoinduced proton pump found abundantly in ocean and fresh water habitat, and has an important role in photoenergy conversion to bioenergy in the living cells. Numerous sequences that encode PR protein variants were discovered by environmental genome sequencing and they indicated the high sequence similarity. A new-type of PR (YS-PR) which had been discovered from the surface of Yellow Sea was found to have only 5 amino acid differences from the previously known green-light absorbing PR (GPR) protein, but showed different photochemical properties. This YS-PR showed a 10 nm red-shifted absorption maximum, when compared with GPR. It also showed slower photocycling rate than GPR. However, the photoconversion rate of YS-PR was fast enough to pump protons. Four different amino acids out of 5 were similar to Blue-light absorbing PR (BPR), suggesting that those residues might be responsible for the observed spectral and photoconverting properties.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1992년도 한국자동제어학술회의논문집(국제학술편); KOEX, Seoul; 19-21 Oct. 1992
• /
• pp.146-151
• /
• 1992

A two-compartment four-cell model is developed for the adiabatic autoclave slim type reactor for free radical polymerization of low density polyethylene(LDPE). The mass and energy balances give rise to a set of ordinary differential equations, and by analyzing the system it is possible to predict properly not only the reactor performance but also the properties of polymer product. The steady state multiplicity is found to exist and examined by constructing the bifurcation diagram. The effects of various operation parameters on the reactor performance and polymer properties are investigated systematically to show that the temperature distribution plays the central role for the properties of polymer product. Therefore, it is essential to establish a good control strategy for the temperature in each compartment. In this study it is shown that the reactor system can be adoptively controlled by pole-placement algorithm with conventional PID controller. To accomplish a satisfactory control, the estimator and controller are initialized during the period of start-up.