• Structural Engineering and Mechanics
• /
• 제62권1호
• /
• pp.11-20
• /
• 2017

The base force element method (BFEM) is a new finite element method. In this paper, a degenerated 4-mid-node plane element from concave polygonal element of BFEM was proposed. The performance of this quadrilateral element with 4 mid-edge nodes in the BFEM on complementary energy principle is studied. Four examples of linear elastic analysis for plane frame structure are presented. The influence of aspect ratio of the element is analyzed. The feasibility of the 4 mid-edge node element model of BFEM on complementary energy principles researched for plane frame problems. The results using the BFEM are compared with corresponding analytical solutions and those obtained from the standard displacement finite element method. It is revealed that the BFEM has better performance compared to the displacement model in the case of large aspect ratio.

• Journal of the Korean Society of Safety
• /
• 제17권3호
• /
• pp.1-6
• /
• 2002

A dynamic characteristics of shock absorber in the various excitation is investigated experimentally. Work diagrams and characteristic curves are used as a experimental standard. The various excitation conditions temperature and noise are very important factors in associated with the reduction of damping force. It is found that the heat occurrence from shock absorber, the gas shock absorber is much higher than oil shock absorber and increased in high speed. As to the variation of damping force, there are no change when the speed is low but we fixed amount of variation by increasing speed and change of new and old decrease. The sound pressure of the swash noise from cycle of shock absorber, we compared with theory sound pressure by experiment.

• Environmental Analysis Health and Toxicology
• /
• 제23권1호
• /
• pp.47-51
• /
• 2008

The toxicity of environmental pollutants was measured between a image of the surface topography in HeLa cells using atomic force microscopy for the possibility of toxic effect measurement and environmental monitoring. A image of the surface topography by AFM were estimated as toxic endpoints. The surface topography by AFM was observed a change of the cell surface in the environmental pollutants, but the standard of the measurement requires for the dose-effect degree. The overall results indicate that the possibility of measurement using AFM were confirmed a dose-effect degree related toxic effects, but it requres correlation between more various biomarker and AFM's measurements if the possibility of the toxic effect measurement was established.

• Tribology and Lubricants
• /
• 제6권2호
• /
• pp.43-49
• /
• 1990

The Dynamic Behavior in line contacts between the vane tip and camring in an oil hydraulic vane pump with intravanes has been investigated. Variations of the radial acting force of a vane were calculated from previously measured results of dynamic infernal pressure in four chambers surrounding a vane, and variations of the behavior were estimated in both the rotational speed range from 1200 to 2700 rpm and in the delivery pressure range from 10 to 21Mpa. The results indicate the variations of the radial acting force. Under the standard operating condition (to 14 Mpa, 1800 rpm), the radial acting force on the vane is governed by internal dynamic pressures, but it is more influenced by rotating speed at higher than 2000 rpm relatively.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1996년도 한국자동제어학술회의논문집(국내학술편); 포항공과대학교, 포항; 24-26 Oct. 1996
• /
• pp.1083-1086
• /
• 1996

Cold rolling mill process in steel works uses stands of rolls to flatten a strip to a desired thickness. At cold rolling mill process, precalculation determines the mill settings before a strip actually enters the mill and is done by an outdated mathematical model. A corrective neural network model is proposed to improve the accuracy of the roll force prediction. Additional variables to be fed to the network include the chemical composition of the coil, its coiling temperature and the aggregated amount of processed strips of each roll. The network was trained using a standard backpropagation with 4,944 process data collected from no.1 cold rolling mill process from March 1995 through December 1995, then was tested on the unseen 1,586 data from Jan 1996 through April 1996. The combined model reduced the prediction error by 32.8% on average.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 한국펄프종이공학회 2007년도 추계학술발표논문집
• /
• pp.325-330
• /
• 2007

Uniaxial tensile test are generally much simpler than uniaxial compressive test. Uniaxial compressive test is experimentally more difficult because of the low buckling resistance of a sheet of paper. In order to avoid buckling, many researchers have applied various lateral restraint techniques to investigate paper uniaxial compression behavior. Adding unnecessary force to inhibit compressive deformation of the sheet is unwanted, but sufficient force must be used to inhibit buckling. This study has been carried out to develop new uniaxial compressive standard test method without exerting unnecessary force to paper specimen to prevent buckling.

• Journal of Institute of Control, Robotics and Systems
• /
• 제13권8호
• /
• pp.777-782
• /
• 2007

Human Robot Interaction(HRI) through a haptic interface plays an important role in controlling robot systems remotely. The augmented usage of bio-signals in the haptic interface is an emerging research area. To consider operator's state in HRI, we used bio-signals such as ECG and blood pressure in our proposed force reflection interface. The variation of operator's state is checked from the information processing of bio-signals. The statistical standard variation in the R-R intervals and blood pressure were used to adaptively adjust force reflection which is generated from environmental condition. To change the pattern of force reflection according to the state of the human operator is our main idea. A set of experiments show the promising results on our concepts of human adaptive interface.

• Proceedings of the KSME Conference
• /
• 대한기계학회 2001년도 춘계학술대회논문집A
• /
• pp.837-841
• /
• 2001

The column-type sensing element in building and mechanical construction parts was designed as three forces and three moments sensor by attaching strain gages approximately. Compared to conventional multi-component sensor, the designed sensor can solve the problem about low stiffness and high cost. The radius of the column was designed analytically and compared with finite element analysis. The coupling errors between components were minimized by using addition and subtraction procedure of signals. The fabricated sensor was tested by using a deadweight force standard machine and a six-component force calibration machine in Korea Research Institute of Standards and Science(KRISS). The calibration showed that the multi-component force/moment sensor had coupling error less than 19.8 % between $F_x$ and $M_y$ components, and 9.0 % in case of other components.

• Journal of Institute of Control, Robotics and Systems
• /
• 제9권1호
• /
• pp.30-36
• /
• 2003

Driving and pick-off using electromagnetic force for a cylindrical vibratory gyroscope is considered. A gyroscope consisting of thin cylindrical vibrating element and electromagnetic drive and pick-off element is designed, fabricated and tested. The results of the proposed pick-off method were compared with the results of the highly precise laser interferometer and eddy current sensor as it was used as the reference standard. Through the experiment, it is verified that the proposed electromagnetic driving and pick-off method can be an effective alternative to conventional electrostatic or piezo-electric methods.

• Structural Engineering and Mechanics
• /
• 제40권1호
• /
• pp.121-148
• /
• 2011

Closed form solutions for equilibrium and flexibility matrices of the Mindlin-Reissner theory based eight-node rectangular plate bending element (MRP8) using Integrated Force Method (IFM) are presented in this paper. Though these closed form solutions of equilibrium and flexibility matrices are applicable to plate bending problems with square/rectangular boundaries, they reduce the computational time significantly and give more exact solutions. Presented closed form solutions are validated by solving large number of standard square/rectangular plate bending benchmark problems for deflections and moments and the results are compared with those of similar displacement-based eight-node quadrilateral plate bending elements available in the literature. The results are also compared with the exact solutions.