• Journal of the Korean Wood Science and Technology
• /
• 제36권2호
• /
• pp.73-78
• /
• 2008

Inorganic chemical treated wood was prepared by impregnation of calcium or magnesium chloride ($CaCl_2$ or $MgCl_2$) solution and immersion in saturated solution of ammonium fluoride ($NH_4F$) as a reactant in order to make an introduction of a refractory fluorides with fungicidal and insecticidal effects in wood. The weight percent gains (WPGs) were increased with increase in concentration of calcium chloride or magnesium chloride solution, and were higher in treatment with calcium chloride than with magnesium chloride. Inorganic substances were produced mainly in the lumina of tracheides. These substances were proved to be the calcium fluoride or magnesium fluoride by the energy dispersive X-ray analyzer in conjunction with a scanning electron microscope (SEM-EDX). The treated wood showed good decay resistance because the weight losses were hardly occurred by the test fungi such as Tyromyces palustris and Trametes versicolor. The fire resistance effect was superior to the treated wood compared with that of the untreated wood.

• Journal of Pharmaceutical Investigation
• /
• 제4권1_2호
• /
• pp.1-6
• /
• 1974

S-Benzylthiuronium chloride reacts with ethylene glycol, derived from hydrolysis of the fluorides, to produce a crystalline substances. Using this, the fluorides can be indentified by measuring melting point. And when the zirconium-alizarin solution reacts with ethylenefluoro hydrin or ${\beta}-fluoroethyl$ acetate, the red-violet color disappears to produce a yellow dye, which exhibits absorption maximum at about $530\;m{\mu}$ using the 250-microgram standard. Using these properties, the fluorine compounds can be determined conveniently by this method.

• 대한화학회지
• /
• 제6권1호
• /
• pp.73-77
• /
• 1962

Yields of hydrogen, methane, carbon monoxide, formaldehyde and ethylene glycol by gamma-radiolysis of methanol have been determined at room temperature and compared with values reported in the literature. The G-values obtained by the present studies are as follows: $G(H_2)=4.98,\;G(CH_4)=0.28,\;G(CO)=0.09,\;G(HCHO)=2.14\;and\;G(C_2H_6O_2)=3.07.$ The effects of water, methyl borate and alkali halides added to methanol prior to radiolysis have also been investigated. It is observed that alkali iodides and bromides affect the G-values, particularly, of hydrogen, formaldehyde and/or ethylene glycol, whereas alkali chlorides and fluorides have less pronounced effects.

• 공업화학
• /
• 제20권5호
• /
• pp.557-560
• /
• 2009

본 연구에서는 글라스를 $100{\mu}m$ 이하의 두께로 박판화하기 위한 새로운 습식 에칭방법 및 에칭 용액을 검토하였다. $NH_4F$ 또는 $NH_4HF_2$를 주성분으로 황산 또는 질산을 첨가한 경우 에칭 용액의 불산 함유량을 저감하는 데에 효과가 있었다. 혼산 용액의 조성과 온도의 영향을 검토하였으며, 음이온계 계면활성제의 첨가는 에칭반응에 의해 생성되는 슬러지의 부착을 억제해주는 효과가 있었다. 수류 발생부를 가지는 새로운 파일럿 장비를 사용하여 상용 무알칼리 글라스와 소다라임 글라스의 에칭 실험을 실시하였다. $640{\mu}m$ 두께의 무알칼리 글라스를 $45{\mu}m$ 두께로 $500{\mu}m$ 두께의 소다라임 글라스를 $100{\mu}m$ 두께로 박판화하였으며, 에칭 후의 표면 조도는 $0.01{\sim}0.02{\mu}m$를 유지하였다.

• 대한소아치과학회지
• /
• 제24권1호
• /
• pp.148-172
• /
• 1997

Sixty human premolar teeth were used for this in vitro study. After each tooth was sectioned mesiodistally, one half was used for the experimental group and the other half for the control. Three groups were made for each fluoride applying method and twenthy teeth were assigned to each group. Ten teeth were used for evaluating total fluoride amount and the other ten were used for firmly-bound fluoride. Fluorshield was used for fluoride-releasing sealant and 1.23% APF, 0.05% NaF were used for topical application fluorides. Each tooth was cleaned with a tooth brush using nonfluoride containing pumice before the experiment. In the sealant group, fluoroshield was applied to the enamel surface without etching procedure and stored in $37^{\circ}C$ saline for 30 days. After 30 days, sealant was removed with explorer without scratching the enamel surface and washed with distilled water and dried. In the APF group, each tooth was immersed in 1.23% APF for 30 min then washed and dried in the same manner. In the NaF group, each tooth was immersed in 0.05% NaF for 24 hours then washed and dried as described above. After each fluoride regimen was applied, ten teeth were randomly selected from each group and immersed in 1M KOH solution for 24 hours to remove loosely-bound fluoride possibly deposited by the three different fluorides applied. In each group, total fluoride amount deposited and the amount of enamel removed by acid biopsy were calculated. After loosely-bound fluoride was removed, firmly-bound fluoride deposited and the amount of enamel removed by acid biopsy were also calculated. Total fluoride amount deposition was significantly increased in the APF and NaF groups, but not in the sealant group. Amount of enamel removed by acid-biopsy was also significantly diminished in the APF and NaF groups, but not in the sealant groups. After loosely-bound fluoride was removed from each groups, no statistical difference was found in the amount of firmly-bound fluoride in any groups. Also no effect of firmly-bound fluoride on enamel dissolution was shown in any groups after loosely-bound fluoride was removed from each group. In conclusion, topical application method of APF or NaF is more effective than fluoride-releasing sealant application to make $CaF_2$ coating on enamel surface and $CaF_2$ coating is the main source for anticariogenic effect of fluoride. However, longterm anticariogenic effect of fluoride-releasing sealant should be further evaluated.

• Restorative Dentistry and Endodontics
• /
• 제40권3호
• /
• pp.209-215
• /
• 2015

Objectives: The aim of this study was to evaluate the fluoride release of conventional glass ionomer cements (GICs) and resin-modified GICs. Materials and Methods: The cements were grouped as follows: G1 (Vidrion R, SS White), G2 (Vitro Fil, DFL), G3 (Vitro Molar, DFL), G4 (Bioglass R, Biodinamica), and G5 (Ketac Fil, 3M ESPE), as conventional GICs, and G6 (Vitremer, 3M ESPE), G7 (Vitro Fil LC, DFL), and G8 (Resiglass, Biodinamica) as resin-modified GICs. Six specimens (8.60 mm in diameter; 1.65 mm in thickness) of each material were prepared using a stainless steel mold. The specimens were immersed in a demineralizing solution (pH 4.3) for 6 hr and a remineralizing solution (pH 7.0) for 18 hr a day. The fluoride ions were measured for 15 days. Analysis of variance (ANOVA) and Tukey's test with 5% significance were applied. Results: The highest amounts of fluoride release were found during the first 24 hr for all cements, decreasing abruptly on day 2, and reaching gradually decreasing levels on day 7. Based on these results, the decreasing scale of fluoride release was as follows: G2 > G3 > G8 = G4 = G7 > G6 = G1 > G5 (p < 0.05). Conclusions: There were wide variations among the materials in terms of the cumulative amount of fluoride ion released, and the amount of fluoride release could not be attributed to the category of cement, that is, conventional GICs or resin-modified GICs.

• 농업과학연구
• /
• 제43권4호
• /
• pp.522-536
• /
• 2016

Fluorine is unique chemical element which occurs naturally, but is not an essential nutrient for plants. Fluoride toxicity can arise due to excessive fluoride intake from a variety of natural or manmade sources. Fluoride is phytotoxic to most plants. Plants which are sensitive for fluorine exposure even low concentrations of fluorine can cause leave damage and a decline in growth. All vegetation contains some fluoride absorbed from soil and water. The highest levels of F in field-grown vegetables are found up to $40mg\;kg^{-1}$ fresh weight although fluoride is relatively immobile and is not easily leached in soil because most of the fluoride was not readily soluble or exchangeable. Also, high concentrations of fluoride primarily associated with the soil colloid or clay fraction can increase fluoride levels in soil solution, increasing uptake via the plant root. In soils more than 90 percent of the natural fluoride ranging from 20 to $1,000{\mu}g\;g^{-1}$ is insoluble, or tightly bound to soil particles. The excess accumulation of fluorides in vegetation leads to visible leaf injury, damage to fruits, changes in the yield. The amount of fluoride taken up by plants depending on the type of plant, the nature of the soil, and the amount and form of fluoride in the soil should be controlled. Conclusively, fluoride is possible and long-term pollution effects on plant growth through accumulation of the fluoride retained in the soil.

• 대한소아치과학회지
• /
• 제24권2호
• /
• pp.436-448
• /
• 1997

Topical fluoride application for children is a widely performed procedure in the field of Pediatric Dentistry for its dental caries prevention effects. However, it is recently recognized as having some unwanted effects on several esthetic restorative materials as it roughens the surfaces of the restorative materials. In order to evaluate the surface changes in esthetic restorative materials, the author immersed composite resin, glass ionomer cement, and resin-modified glass ionomer cement specimens in various topical fluoride agents and measured the weight loss and also, examined the specimens under the scanning electron microscope. The followings are the results : 1. All the specimens immersed in APF gel for 4 minutes showed statistically significant weight loss. (paired t-test, P<0.05). 2. There was no statistically significant weight loss for the resin-modified glass ionomer cement and composite resin groups immersed in sodium fluoride solution (paired t-test, P>0.05). 3. When the glass ionomer cement group was immersed in APF gel for 1 and 4 minutes, there was a statistically significant weight loss compare to other esthetic restorative materials (ANOVA, P<0.05). 4. In the resin-modified glass ionomer cement group and the composite resin group, weight loss in the APF gel 4 minutes immersion group was greater than the 1 minute immersion group, and it was statistically significant (ANOVA, P<0.05). 5. When the specimens were examined under scanning electron microscope, the surface changes were greatest in the order of glass ionomer cement, resin-modified glass ionomer cement, composite resin and also in the order of APF gel 4 minute immersion group, 1 minute immersion group, sodium fluoride immersion group, and control group.

• 대한소아치과학회지
• /
• 제31권3호
• /
• pp.381-390
• /
• 2004

Normal pulsed Nd:YAG 레이저 조사와 불소화합물이 산성음료수에 의해 탈회된 법랑질의 표면 미세경도에 미치는 재광화 효과를 평가하고자 한다. 법랑질 시편을 제작하여 50ml 플라스틱 시험관 5개에 코카콜라를 채운 후 30개의 소구치를 6개씩 나누어 넣고 탈회시켰다. 법랑질 표면에 6W 출력하의 50mJ 에너지 밀도, 20Hz의 pulse rate로 레이저를 조사하였다. 레이저가 조사된 법랑질 표면에 각 군별로, 여러 형태의 불소화합물을 처리한 후 탈회 전, 후의 미세경도 및 Diagnodent를 측정하였다. 동일한 방법으로 탈회된 법랑질에 레이저를 조사했을 때와 레이저가 조사된 법랑질 표면에 불소화합물을 처치한 후에 미세경도 및 Diagnodent를 측정하였다. 법랑질 표면을 산성 음료에 탈회 후, 레이저 조사 후, 불소화합물 처치 후의 각각의 시편에 대하여, 주사전자현미경으로 1500배 확대하여 관찰하였다. 1. 산성 탈회된 법랑질 표면의 미세경도(VHN)가 레이저를 조사한 후와 불소 도포 후에 증가하였으나, 레이저 조사 후의 경도와 불소도포후의 경도간의 차이는 유의하지 않았다. 2. 초기 경도, 탈회 후 경도, 레이저 조사 후 경도, 불소 도포 후 경도에서 불소군 간의 차이는 모두 유의하지 않았고, 불소용액 군과 불소 젤 군에서는 레이저 조사 후의 경도와 불소 도포 후의 경도간에 유의한 차이가 없었으나, 불소 바니쉬 군에서는 유의한 차이가 있었다. 3. Diagnodent 측정치의 변화에서 초기 점수, 탈회 후 점수, 레이저 조사 후의 점수와 불소 도포 후의 점수간에는 유의한 차이가 있었고, 레이저 조사 후 점수와 불소 도포 후의 점수가 불소 도포 군 사이에서는 유의한 차이가 없었다. 4. 산성 음료수에 탈회된 법랑질 표면에의 Nd:YAG 레이저 조사는 재광화에 효과적이며, 불소화합물의 처치는 레이저의 효과를 증가시키는 부가적인 효과를 갖는다. 5. 주사 전자 현미경상에서 Nd:YAG 레이저가 조사된 법랑질 표면은 전체 표면이 법랑소주가 녹아내려 융합된 매끈한 바닥에 균열이 생기고 분화구가 퍼져 있는 양상을 보였으며 불소 도포 후에는 균열과 분화구 형태는 뚜렷하지 않으며 탈회된 후의 표면에 가까운 양상을 보였다.

• 대한소아치과학회지
• /
• 제33권2호
• /
• pp.262-268
• /
• 2006

연구목적은 산성 음료수에 의해 탈회된 법랑질의 표면에 대한 Nd:YAG레이저 조사의 재광화 효과와 불화물 도포의 효과를 평가하는 것이다. 치아우식증, 색소, 손상, 부착물이 없는 건전한 사람의 유치의 평활면으로부터 법랑질 시편을 제작하고, 코카콜라에 12시간 동안 담가 탈회시켰다. 탈회된 법랑질 표면에 6W출력, 50mJ, 20Hz pulse rate의 에너지 밀도로 Nd:YAG 레이저를 조사하였다. 탈회 전후와 레이저 조사 후에 미세경도 및 Diagnodent 점수를 측정한 후, 0.05% 불소 용액, 1.23% 불소 젤, 0.1%불소 바니쉬 중의 한 가지를 도포하였으며 미세경도 및 Diagnodent측정을 통하여 레이저의 재광화 효과와 불소의 효과를 평가하였다. 1. Diagnodent 측정치의 변화에서, 탈회 후에는 초기 점수의 23.51%로 감소하였고, 레이저 조사 후에는 초기 점수의 37.37%로 증가하였으며, 불소도포 후에는 초기 점수의 51.34%로 증가하였고, 전체적으로 보면 초기 점수, 탈회 후 점수. 레이저 조사 후의 점수, 불소도포 후의 점수 및 그 백분율 사이에 모두 유의한 차이가 있었다(P<0.05). 3개 불소군 사이의 차이는 초기점수 및 불소도포 후 점수와 백분율에서 모두 유의하지 않았으며 각 불소군 내에서는 불소 용액군과 불소 바니쉬군에서 초기 점수, 탈회 후 점수, 레이저 조사 후의 점수, 불소도포 후의 점수 및 그 백분율사이에 모두 유의한 차이가 있었고, 불소 젤군에서는 레이저 조사 후와 불소도포 후의 점수 및 백분율 사이에 유의한 차이가 없었다. 2. 미세경도의 변화에서, 탈회 후의 경도는 초기 경도의 33.58%로 감소하였고, 레이저 조사 후의 경도는 초기 경도의 43.99%로 증가하였으며, 불소도포 후의 경도는 초기 경도의 51.38%로 증가하였고, 전체적으로 보면 초기 경도, 탈회 후 경도, 레이저 조사 후의 경도, 불소도포 후의 경도 및 그 백분율 사이에 모두 유의한 차이가 있었다(P<0.05). 불소군 별로 보면 3개 불소군 사이의 차이는 모두 유의하지 않았고, 백분율에서도 초기경도와 불소도포 후 경도에서 유의하지 않았으며, 각 불소군 내에서는 초기 경도, 탈회 후 경도, 레이저 조사 후의 경도, 불소도포 후의 경도 및 백분율 사이에 모두 유의한 차이가 있었다.